Hostname: page-component-7b7567c8c-7pwfn Total loading time: 0 Render date: 2026-11-17T08:35:58.420Z Has data issue: false hasContentIssue false

Horizontal tail local angle-of-attack and total pressure measurements through static pressure ports and Kiel pitot

Published online by Cambridge University Press:  16 October 2019

R. M. Granzoto*
Affiliation:
Embraer S.A., São José dos Campos, Brazil
L. A. Algodoal
Affiliation:
Embraer S.A., São José dos Campos, Brazil
G. J. Zambrano
Affiliation:
Embraer S.A., São José dos Campos, Brazil
G. G. Becker
Affiliation:
Embraer S.A., São José dos Campos, Brazil
Rights & Permissions [Opens in a new window]

Abstract

Aircraft handling qualities may be influenced by wing-tip flow separations and horizontal tail (HT) reduced efficiency caused by loss of local dynamic pressure or local tailplane flow separations in high angle-of-attack manoeuvres. From the flight tester’s perspective, provided that the test aircraft presents sufficient longitudinal control authority to overcome an uncommanded nose-up motion, this characteristic should not be a safety factor. Monitoring and measuring the local airflow in the aircraft’s HT provides information for safe flight-test envelope expansion and data for early aerodynamic knowledge and model validation. This work presents the development, installation and pre-flight calibration using computational fluid dynamics (CFD), flight-test calibration, results and benefits of differential pressure based local angle-of-attack and total pressure measurements through 20 static pressure ports and a Kiel pitot. These sensors were installed in a single-aisle, four-abreast, full fly-by-wire medium-range jet airliner with twin turbofan engines and conventional HT (low vertical position).

Information

Type
Research Article
Copyright
© Royal Aeronautical Society 2019 
Figure 0

Figure 1.Schematic system architecture of the system

Figure 1

Figure 2.HT sensors positions and installation.

Figure 2

Figure 3.Body-Horizontal-Tail mesh – with elevator two different elevator deflections.

Figure 3

Figure 4.: Example of $\alpha_{\rm{HT1}}$ as function of ${\rm C}_{\rm P}$ for some pressure taps.

Figure 4

Figure 5.Wing-Body-Pylon-Nacelle configuration CFD runs showing wing and engine effects on local virtual HT position.

Figure 5

Figure 6.Local angle-of-attack at virtual HT position as a function of span position for various aircraft angle-of-attack – Landing flaps configuration.

Figure 6

Figure 7.${\alpha}_{\rm{HT}}$ components contribution comparison during a flight-test stall manoeuvre.

Figure 7

Figure 8.Calibration flight-test results – comparison between ${\Delta{\rm I}}_{\rm{HT}}$ and ${\rm K}_{1}\Delta\alpha_{\rm{HT}}$ – Cruise Flaps Configuration.

Figure 8

Figure 9.Calibration flight-test results – comparison between ${\Delta{\rm I}}_{\rm{HT}}$ and ${\rm K}_{1}\Delta\alpha_{\rm{HT}}$ – Take-off Flaps Configuration.

Figure 9

Figure 10.Calibration flight-test results – comparison Between ${\Delta{\rm I}}_{\rm{HT}}$ and ${\rm K}_{1}\Delta\alpha_{\rm{HT}}$ – Landing Flaps Configuration.

Figure 10

Figure 11.$\alpha_{\rm{HT}}$ and $\varepsilon$ comparison between simulation based on wind tunnel data and flight-test data during a stall manoeuvre – Cruise Flaps Configuration.

Figure 11

Figure 12.Tufts flow visualisation combined with HT measurements during a high incidence flight-test manoeuvre.

Figure 12

Figure 13.Local $\alpha_{\rm{HT}}$ and downwash comparison between wind-tunnel data and flight-test data during a stall manoeuvre – Cruise Flaps Configuration.

Figure 13

Figure 14.Local $\alpha_{\rm{HT}}$ and downwash comparison between wind-tunnel data and flight-test data during a stall manoeuvre – Low Take-off Flaps Configuration.

Figure 14

Figure 15.Local $\alpha_{\rm{HT}}$ and downwash comparison between wind-tunnel data and flight-test data during a stall manoeuvre – High Take-off Flaps Configuration.

Figure 15

Figure 16.Local $\alpha_{\rm{HT}}$ and downwash comparison between wind-tunnel data and flight-test data during a stall manoeuvre – Landing Flaps Configuration.

Figure 16

Figure 17.Flight-test measurement of dynamic pressure ratio between local and global dynamic pressure $(\eta)$ – Cruise Flaps Configuration.

Figure 17

Figure 18.Flight-test measurement of dynamic pressure ratio between local and global dynamic pressure – Low Take-off Flaps Configuration.

Figure 18

Figure 19.Flight-test measurement of dynamic pressure ratio between local and global dynamic pressure $(\eta)$ – High Take-off Flaps Configuration.

Figure 19

Figure 20.Flight-test measurement of dynamic pressure ratio between local and global dynamic pressure $(\eta)$ – Landing Flaps Configuration.

Figure 20

Table 1Differences between flight-test results and estimated wind-tunnel parameters $\varepsilon_{0}$ and $\text{d}\varepsilon/\text{d}\alpha$