Hostname: page-component-7b7567c8c-fvjsw Total loading time: 0 Render date: 2026-11-17T07:35:58.442Z Has data issue: false hasContentIssue false

Reacting flow analysis of a cavity-based scramjet combustor using a Jacobian-free Newton–Krylov method

Published online by Cambridge University Press:  27 December 2018

R. Rouzbar*
Affiliation:
Middle East Technical UniversityAnkaraTurkey
S. Eyi
Affiliation:
Middle East Technical UniversityAnkaraTurkey
Rights & Permissions [Opens in a new window]

Abstract

The scramjet is a rather a new technology and there are many issues related to their operation, especially when it comes to the combustion processes. Combustion in high-speed flows causes various problems such as flame instability and poor fuel–air mixing efficiency. One of the methods used to overcome these problems is to recess a cavity in the combustor wall where a secondary flow is generated. In this study, a computational fluid dynamics (CFD) code is developed to analyse the reacting flow passing through the cavity-based scramjet combustor. The developed code is based on three-dimensional coupled Navier–Stokes and finite rate chemistry equations. An ethylene-air reduced chemical reaction model is used as a fuel–air combination. The Spalart–Allmaras model is utilised for turbulence closure. The non-dimensional form of the flow and chemical reaction equations are discretised using a finite volume method. The Jacobian-Free Newton–Krylov (JFNK) method is used to solve the coupled system of non-linear equations. The JFNK is a matrix-free solution method which improves the computational cost of Newton’s method. The parameters that affect the performance of the JFNK method are studied in the analysis of a scramjet combustor. The influence of the forcing term on the convergence of the JFNK method is studied in the analysis of scramjet combustor. Different upwind flux vector splitting methods are utilised. Various flux limiter techniques are employed for the calculations of higher order flux vectors. The effects of flux vector splitting and flux limiter methods on the convergence and accuracy of the JFNK method are evaluated. Moreover, the variations of the mixing efficiency with fuel injection angles are studied.

Information

Type
Research Article
Copyright
© Royal Aeronautical Society 2018 
Figure 0

Table 1Forward reaction rate data for reduced ethylene–air combustion(4)

Figure 1

Figure 1Schematic of the experimental scramjet(24).

Figure 2

Figure 2Two-dimensional drawing of the combustor.

Figure 3

Figure 3Upstream fuel injection configuration (top view).

Figure 4

Figure 4Convergence of JFNK method with different flux splitting methods (first-order schemes).

Figure 5

Table 2CPU times of JFNK method with different flux splitting methods (first-order schemes)

Figure 6

Figure 5Converge of JFNK method with first- and second-order schemes. (a) Steger-Warming; (b) AUSM; and (c) van Leer.

Figure 7

Table 3CPU times of JFNK method with second-order schemes

Figure 8

Figure 6Effects of limiters on convergence of JFNK method.

Figure 9

Figure 7Effects of forcing term on convergence of JFNK method. (a) First and (b) second orders.

Figure 10

Table 4Variation of CPU time for different forcing terms

Figure 11

Table 5Generated meshes with different resolutions

Figure 12

Figure 8Medium grid size generated for viscous flows.

Figure 13

Figure 9Comparison of pressure distribution with experimental and numerical data.

Figure 14

Table 6Variation of CPU time for different grid resolutions

Figure 15

Figure 10Pressure (a) and temperature (b) variations (second-order scheme).

Figure 16

Figure 11Species mass fraction variations (second-order scheme). (a) Oxygen mass fraction; (b) carbon dioxide mass fraction and (c) dihydrogen monoxide mass fraction.

Figure 17

Figure 12Cavity section of the combustor.

Figure 18

Figure 13Two-dimensional distribution of flow variables at different axial locations. Temperature at (a) x = 0.17 m; (b) x = 0.23 m; and (c) x = 0.31 m. Density at (d) x = 0.17 m; (e) x = 0.23 m; and (f) x = 0.31 m. Oxygen at (g) x = 0.17 m; (h) x = 0.23 m; and (i) x = 0.31 m. Carbon dioxide at (j) x = 0.17 m; (k) x = 0.23 m; and (l) x = 0.31 m.

Figure 19

Figure 14Comparison of first- and second-order schemes by contour. Density ((a) first and (b) second orders). Temperature ((c) first and (d) second orders). Carbon dioxide mass fraction ((e) first and (f) second orders). Oxygen mass fraction ((g) first and (h) second orders).

Figure 20

Figure 15Variation of mass flux-weighted temperature (a) and mixing efficiency (b).

Figure 21

Figure 16Mass flux weighted 1D variation of species through combustor. (a) Ethylene; (b) oxygen; (c) carbon monoxide; (d) hydrogen; (e) carbon dioxide; and (f) dihydrogen monoxide.

Figure 22

Figure 17Mixing efficiency for different fuel injection angles. (a) In flow direction and (b) against flow direction.

Figure 23

Figure 18Flow in the cavity region. (a) Velocity vectors and (b) streamlines.