This study investigates the combustion characteristics (lean blowoff (LBO), flashback, and combustion instability) of sustainable aviation fuels (SAFs) using a two-staged combustor arranged in tandem. The combustor consists of a first (main) burner with an axial swirler and a second burner (afterburner) with a V-gutter bluff-body. The main burner utilises a constant flow rate of CH4/Air as reactants, while the afterburner operates on the combustion product from the first burner, additional dilution air, and one of the six liquid test fuels (Jet-A, A-2, C-1, C-5, C-9, and JP-8/HRJ) as reactants. When test fuels with higher derived cetane number (DCN) are used in the afterburner, it is observed that LBO occurs at lower afterburner global equivalence ratios (${\phi _{af}}$). This is due to the smaller chemical time scale of those test fuels, which enables the flame to be sustained under higher flow speeds. This is consistent with the results of previous studies. Additionally, this study shows that flashback also occurs at lower equivalence ratio for test fuels with higher DCN. This is a new finding and can be explained in a similar way to LBO. As the operating conditions approach the LBO or exceed flashback limits, the reactivity of shear layer also decreases, creating favourable conditions for them to occur. Moreover, for test fuels with low DCN (C-1 and C-5), blowoff occurs instead of flashback as ${\phi _{af}}$ increases. This can be attributed to the stronger pressure perturbation resulting from combustion instability in these flames compared to others. It demonstrates a stronger correlation between the pressure perturbation and the heat release rate fluctuation for C-1 and C-5 than that of other test fuels at the same equivalence ratio. In conclusion, it was found that test fuels with higher DCN have advantages in terms of LBO and stability, however, they are more prone to flashback.

Hydrogen is a promising energy carrier to decarbonise aviation. However, many challenges regarding its storage or handling still have to be solved to successfully utilise hydrogen in aircraft and at airport infrastructures. The increasing use of hydrogen also generates opportunities for disruptive improvements, like the possibility to integrate metal hydrides (MHs) into the hydrogen powertrain and its infrastructure. Besides their ability to store hydrogen, MHs enable a wide range of potential secondary functions such as high-power thermal applications or compression. This way, MHs may contribute to achieve the goal of sustainable hydrogen-powered aviation. Hence, potential MH application options and their current state-of-the-art are presented. Based on that overview, the following seven use cases for aviation are selected for evaluation: ‘hydrogen emergency storage’, ‘cabin air-conditioning’, ‘thermal management of fuel cells’, ‘gas gap heat switches’, ‘hydrogen boil-off recovery’, ‘onboard hydrogen compression’ and ‘hydrogen safety sensors’. Four of these use cases are investigated to achieve comparable degrees of detail to avoid misevaluations in the subsequent weighted point rating. The results reveal the high potential of MHs for ‘hydrogen boil-off recovery’, ‘hydrogen safety sensors’ and ‘cabin air-conditioning’. For the three most promising use cases, outlooks to their potential future implementation are provided in order to outline the ability of MHs to empower sustainable aviation. These investigations highlight the huge potential of MHs for boil-off treatment.

Water vapour and particles in aero engine exhaust can give rise to condensation trails (contrails) in the wake of aircrafts, and recent studies suggest that persistent contrails and contrail cirrus account for circa 50% of the total aviation-derived radiative forcing (RF). The Schmidt-Appleman criterion is widely used to qualitatively predict the formation of contrails. The criterion indicates that the formation of contrails is affected by both aero engine exhaust and ambient air conditions and can therefore provide the theoretical basis to devise contrail mitigation strategies and further allows quantitative assessment of these strategies. This work focuses on water extraction from the aircraft engine exhaust for contrail mitigation. The fuel water emission index (${\rm{E}}{{\rm{I}}_{{{\rm{H}}_2}{\rm{O}}}}$) is one of the key factors that determines whether persistent contrails form or not. It indicates the amount of water produced for every kg of fuel burnt. Research has indicated that water extraction from the exhaust of the aero engine has been considered for Nitrogen oxides (NOx) reduction, but not for contrail mitigation. Assuming that water extraction is indeed possible, the emphasis of this work will therefore be on understanding how much water is needed to be extracted for contrail mitigation depending on the altitude and the relative humidity (RH), with the aim to carry out a meaningful study on the mitigation of persistent contrails and contrail cirrus to enable a fast and considerable reduction in aviation-derived RF.

This contribution focuses on the abatement with hydrogen of CO2 and non-CO2 emissions. It is agenda-setting in two respects. Firstly, it challenges the globally accepted hydrocarbon sustainable aviation fuel (SAF) pathway to sustainability and recommends that our industry accelerates along the hydrogen pathway to ‘green’ aviation. Secondly, it reports a philosophical and analytical investigation of appropriate accuracy on abatement strategies for nitrogen oxides and contrails of large hydrogen airliners. For the second contribution, a comparison is made of nitrogen oxide emissions and contrail avoidance options of two hydrogen airliners and a conventional airliner of similar passenger capacity. The hydrogen aircraft are representative of the first and second innovation waves where the main difference is the weight of the hydrogen tanks. Flights of 1000, 2000, 4000 and 8000 nautical miles are explored. Cranfield’s state of the art simulators for propulsion system integration and gas turbine performance (Orion and Turbomatch) were used for this. There are two primary contributions to knowledge. The first is a new set of questions to be asked of SAF and hydrogen decarbonising features. The second is the quantification of the benefits from hydrogen on non-CO2 emissions. For the second generation of long-range hydrogen-fuelled aircraft having gas turbine propulsion, lighter tanks (needing less thrust and lower gas temperatures) are anticipated to reduce NOx emissions by over 20%; in the case of contrails, the preliminary findings indicate that regardless of the fuel, contrails could largely be avoided with fuel-burn penalties of a few per cent. Mitigating action is only needed for a small fraction of flights. For conventional aircraft this penalty results in more CO2, while for hydrogen aircraft the additional emission is water vapour. The conclusion is that our research community should continue to consider hydrogen as the key ‘greening’ option for aviation, notwithstanding the very significant costs of transition.

The current paper is focused on the conceptual design of a thermal management system with a liquid working medium for a commuter hybrid-electric aircraft, featuring a series propulsion configuration. Regarding the system’s architecture, parametric analyses are conducted, by altering the number of heat exchangers. To clarify, a centralised and a decentralised thermal management system architecture are examined. Furthermore, a computational model calculates the temperatures during the system’s operation and the required coolant mass flows to sufficiently cool all the compartments. Subsequently, the required heat exchanger surface is determined and the weight of each compartment that comprises the thermal management system can be calculated. It is worth noting, that the compartments’ cold plate weight is integrated. The results indicate that the decentralised configuration results in lower temperature fields for all components compared to the centralised configuration. However, the latter weighs 32.2% lower at 158.22kg while the decentralised configuration weighs 233.48kg.

Hybrid-electric propulsion is a promising alternative to sustainable aviation and is mainly considered for the commuter and regional aircraft class. However, the development of hybrid-electric propulsion variants is affected by the technology readiness level of electric components. The components’ technology will determine the electrification benefit, compared to a conventional aircraft, and will suggest which is the most beneficial variant and which has a closer entry into service date. Within this work, three different dates are explored, namely 2027, 2030 and 2040, to size three Parallel and three Series hybrid-electric architecture variants using an in-house aircraft sizing tool. All variants are compared to a conventional configuration sized using technological assumptions of 2014, with the main comparison metrics being the aircraft block fuel, energy consumption, direct operating cost and holistic environmental impact. On one hand, the Parallel configurations have reduced maximum take-off mass and mission energy consumption compared to the Series, however, the latter show a greater potential for block fuel reduction and require less onboard energy for the same mission. The annual operating cost evaluation indicates that the Parallel hybrid variant of 2030 has greater operational costs than the respective Series variant; however, it has reduced capital costs compared to the latter, making it more economical to operate considering both costs. Additionally, in the case of an energy recession, both hybrid variants of 2030 show a further cost reduction, with the Series having a total reduction of 10.4% excluding capital costs, compared to the reference aircraft. Moreover, the life cycle assessment shows that the Series variants have a lower environmental impact, both compared to the reference aircraft and the Parallel variants. The former could be up to 59.7% less detrimental to the environment than the reference aircraft, whereas the latter up to 23.9%, with the integration of renewable sources for electricity production. Finally, by the year 2040, the Series variant shows outstanding performance in all comparison metrics, compared to the Parallel and the reference aircraft.

Civil aircraft that fly long ranges consume a large fraction of civil aviation fuel, injecting an important amount of aviation carbon into the atmosphere. Decarbonising solutions must consider this sector. A philosophical-analytical feasibility of an airliner family to assist in the elimination of carbon dioxide emissions from civil aviation is proposed. It comprises four models based on the integration of the body of a large two-deck airliner with the engines, wings and flight surfaces of a long-range twin widebody jet. The objective of the investigation presented here is to evaluate the impact of liquid hydrogen tank technology in terms of gravimetric efficiency. A range of hydrogen storage gravimetric efficiencies was evaluated; from a pessimistic value of 0.30 to a futuristic value of 0.85. This parameter has a profound influence on the overall fuel system weight and an impact on the integrated performance. The resulting impact is relatively small for the short-range aircraft; it increases with range and is important for the longer-range aircraft. For shorter-range aircraft variants, the tanks needed to store the hydrogen are relatively small, so the impact of tank weight is not significant. Longer range aircraft are weight constrained and the influence of tank weight is important. In the case of the longest range, the deliverable distance increases from slightly over 4,000 nautical miles, with a gravimetric efficiency of 0.3, to nearly 7,000 with a gravimetric efficiency of 0.85.

With an annual growth in travel demand of about 5% globally, managing the environmental impact is a challenge. In 2019, the International Civil Aviation Organisation (ICAO) issued emission reduction targets, including well-to-wake greenhouse gas (GHG) emissions reduced at least 50% from 2005 levels by 2050. This discusses several technologies from an aircraft design perspective that can contribute to achieving these targets. One thing is certain: aircraft will look different in the future. The Transonic Truss-Braced Wing and Flying V configurations are promising significant efficiency improvements over conventional configurations. Electric propulsion, in various architectures, is becoming a feasible option for general aviation and commuter aircraft. It will be a growing field of aviation with zero-emissions flight and opportunities for special missions. Lastly, this paper discusses methods and design processes that include all relevant disciplines to ensure that the aircraft is optimised as a complete system. While empirical methods are essential for initial design, Multidisciplinary Design Optimisation (MDO) incorporates models and simulations integrated in an optimisation environment to capture critical trade-offs. Concurrent design places domain experts in one site to facilitate collaboration, interaction, and joint decision-making, and to ensure all disciplines are equally considered. It is supported by a Collaborative Design Facility (CDF), an information technology facility with connected hardware and software tools for design analysis.

An electric propulsion model for propeller-driven aircraft is developed with the aim of minimising the power consumption for a given airspeed and thrust. Blade Element Momentum Theory (BEMT) is employed for propeller performance predictions fed with aerodynamic aerofoil data obtained from a proposed combined Computational Fluid Dynamics (CFD)–Montgomerie method, which is also validated. The Two-Dimensional (2D) aerofoil data are corrected to consider compressibility, three-dimensional, viscous and Reynolds-number effects. The BEMT model showed adequate fitting with experimental data from the University of Illinois Urbana Champaign (UIUC) database. Additionally, Goldstein optimisation via vortex theory is employed to design pitch and chord distributions minimising the induced losses of the propeller. Particle swarm optimisation is employed to find the optimal value for a wide range of geometrical and operational parameters considering some constraints. The optimisation algorithm is validated through a study case where an existing optimisation problem is approached, leading to very similar results. Some trends and insights are obtained from the study case and discussed regarding the design of an optimal propulsion system. Finally, CFD simulations of the study case are carried out, showing a slight relative error of BEMT.

An unusual philosophical approach is proposed here to decarbonise larger civil aircraft that fly long ranges and consume a large fraction of civil aviation fuel. These inject an important amount of carbon emissions into the atmosphere, and holistic decarbonising solutions must consider this sector. A philosophical–analytical investigation is reported here on the feasibility of an airliner family to fly over long ranges and assist in the elimination of carbon dioxide emissions from civil aviation.

Backed by state-of-the-art correlations and engine performance integration analytical tools, a family of large airliners is proposed based on the development and integration of the body of a very large two-deck four-engine airliner with the engines, wings and flight control surfaces of a very long-range twin widebody jet. The proposal is for a derivative design and not a retrofit. This derivative design may enable a swifter entry to service.

The main contribution of this study is a philosophical one: a carefully evaluated aircraft family that appears to have very good potential for first-generation hydrogen-fuelled airliners using gas turbine engines for propulsion. This family offers three variants: a 380-passenger aircraft with a range of 3,300nm, a 330-passenger aircraft with a range of 4,800nm and a 230-passenger aircraft with a range of 5,500nm. The latter range is crucially important because it permits travel from anywhere in the globe to anywhere else with only one stop. The jet engine of choice is a 450kN high-bypass turbofan.

The potential to recover waste heat from the exhaust gases of a turboprop engine and produce useful work through an Organic Rankine Cycle (ORC) is investigated. A thermodynamic analysis of the engine’s Brayton cycle is derived to determine the heat source available for exploitation. The aim is to use the aircraft engine fuel as the working fluid of the organic Rankine cycle in order to reduce the extra weight of the waste heat recovery system and keep the thrust-to-weight ratio as high as possible. A surrogate fuel with thermophysical properties similar to aviation gas turbine fuel is used for the ORC simulation. The evaporator design as well as the weight minimisation and safety of the suggested application are the most crucial aspects determining the feasibility of the proposed concept. The results show that there is potential in the exhaust gases to produce up to 50kW of power, corresponding to a 10.1% improvement of the overall thermal efficiency of the engine.

New alternative jet fuels have provided many advantages in the aviation industry, especially in terms of economics and environment. However, fuel–seal compatibility is one of the major issues that restricts alternative fuel advancement into the market. Thus, to help understand and solve the problem, this study examines the swelling effect of prepared and non-prepared O-rings in different fuels and aromatic species. Stress relaxation experiments were carried out to evaluate seal compatibility under compression, which mimics engine operation conditions. Seals were compressed and immersed in a variety of fuels and their blends for about 90h while maintaining a constant temperature 30°C and constant compression force of 25% seal thickness. The two types of elastomers investigated were fluorosilicone and nitrile O-rings, which are predominantly used in the aviation industry. Meanwhile, three different fuels and aromatic species were utilised as the variables in the experiments. The fuels used were Jet-A1, SPK and SHJFCS, while the aromatic species added were propyl benzene, tetralin and p-xylene. The swelling effects were determined from the P/Po value. Results indicate that Jet-A1 has the highest swelling effect, followed by SHJFCS and SPK. It was observed that the higher the percentage of aromatics in fuel, the higher the rate of swelling. Furthermore, prepared seals had a lower swelling rate than did non-prepared seals. Meanwhile, the intensity of the swelling effect in the Jet-A1-SHJFCS blends was in the order of 60/40, 85/15 and 50/50 blend. The work done in this study will aid in the selection of suitable aromatic species in future fuels. The novelty of this research lies in the determination of the appropriate amount of aromatic content as well as the selection of type of aromatic and its mixture fuel. Moreover, the various proportions of fuel blends with aromatic are investigated. The primary aim of this study is to understand the behaviour of prepared and non-prepared seals, and their compatibility with alternative fuels.

The increasing use of unmanned aerial vehicles in areas such as rescue, mapping, and transportation have made it necessary to study more accurate techniques for calculating flight time estimates. Such calculations require knowing the battery discharge profile. Simplified flight time calculation methods provide data with uncertainties as they are based solely on manufacturer datasheet information. This study presents a setup to measure the battery discharge curve using a LabVIEW interface with a low-cost acquisition system. The acquired data passes through a nonlinear optimisation algorithm to find the battery coefficients, which enables the more precise estimation of its range and endurance. The great advantage of this model is that it makes it possible to predict how the battery will discharge at different rates using just one experimental curve. The methodology was applied to three different batteries and the model was validated with different discharge rates in a controlled environment, which resulted in endurance lower than 3.0% for most conditions and voltage estimation error lower than 3.0% in operational voltage. The work also presented a methodology for estimating cruise time based on the current used during each flight stage.

Large-eddy simulations (LES) have been employed to investigate the far-field four-vortex wake vortex evolution over 10min behind an aircraft formation. In formation flight scenarios, the wake vortex behaviour was found to be much more complex, chaotic and also diverse than in the classical single aircraft case, depending very sensitively on the formation geometry, i.e. the lateral and vertical offset of the two involved aircraft. Even though the case-by-case variability of the wake vortex behaviour across the various formation flight scenarios is large, the final plume dimensions after vortex dissolution are in general substantially different from those of single aircraft scenarios. The plumes are around 170 to 250m deep and 400m to 680m broad, whereas a single A350/B777 aircraft would produce a 480m deep and 330m broad plume. Formation flight plumes are thus not as deep, yet they are broader, as the vortices do not only propagate vertically but also in span-wise direction. Two different LES models have been employed independently and show consistent results suggesting the robustness of the findings. Notably, $CO_{2}$ emissions are only one contribution to the aviation climate impact among several others like contrails and emission of water vapour and nitrogen oxides, which would be all affected by the implementation of formation flight. Thus, we also highlight the differences in ice microphysical and geometrical properties of young formation flight contrails relative to the classical single aircraft case.

This paper presents the results of an experimental campaign to measure thruster-relevant parameters for a high-power (180kW) inductive propulsion system utilising Ar, $ {\textrm{O}}_{2}$, $ \textrm{N}_{2}$, and $ \textrm{CO}_{2}$ as propellants. Results from the investigation show that inductive thrusters can make use of these propellants without the severe degradation seen in other electric propulsion systems. Furthermore, the collection of experimental data at powers greater than 100kW provides a reference of performance for the high-power electric propulsion devices intended for missions in the near future. Thrust and specific impulse in inductive systems can be improved by preferentially combining the chemical properties of atomic and molecular propellants. The maximum thrust recorded during these experiments was 7.9N, obtained using a combination of argon and oxygen (0.68 Ar + 0.32 $\textrm{O}_{2}$). The combination of argon and molecular propellants also decreased thermal losses within the discharge volume. Specific impulse can be doubled for the same input electric power by combining propellants, and future modifications to the thruster geometry and acceleration mechanism can be used to further improve the performance of such systems.

The RemoveDEBRIS mission has been the first mission to successfully demonstrate, in-orbit, a series of technologies that can be used for the active removal of space debris. The mission started late in 2014 and was sponsored by a grant from the EC that saw a consortium led by the Surrey Space Centre to develop the mission, from concept to in-orbit demonstrations, that terminated in March 2019. Technologies for the capture of large space debris, like a net and a harpoon, have been successfully tested together with hardware and software to retrieve data on non-cooperative target debris kinematics from observations carried out with on board cameras. The final demonstration consisted of the deployment of a drag-sail to increase the drag of the satellite to accelerate its demise.

This study is aimed at establishing a linear holding (LH) procedure instead of a conventional air holding stack to minimize the effects of airborne delays in terms of air traffic management and fuel consumption. This paper uses both actual flight data and the Base of Aircraft Database (BADA) model to obtain fuel consumption for level flight and descent segments, separately.

The total fuel savings obtained by using actual flight data (16%) and the BADA model (10%) indicate that the LH is found to be more advantageous compared to a conventional holding procedure. Furthermore, the recommended LH procedure could be a promising solution for keeping aircraft in a narrow area that could be considered to be an effective method for airspace usage.

Product development, especially in aerospace, has become more and more interconnected with its operational environment. In a constant changing world, the operational environment will be subjected to changes during the life cycle of the product. The operational environment will be affected by not only technical and non-technical perturbations, but also economical, managerial and regulatory decisions, thus requiring a more global product development approach. One way to try tackling such complex and intertwined problem advocates studying the envisioned product or system in the context of system of systems (SoS) engineering. SoSs are all around us, probably in any field of engineering, ranging from integrated transport systems, public infrastructure systems to modern homes equipped with sensors and smart appliances; from cities filling with autonomous vehicle to defence systems.

Since also aerospace systems are certainly affected, this work will present a holistic approach to aerospace product development that tries spanning from needs to technology assessment. The proposed approach will be presented and analysed and key enablers and future research directions will be highlighted from an interdisciplinary point of view. Consideration of the surrounding world will require to look beyond classical engineering disciplines.

One of the main challenges of future aircraft engines is to achieve low pollutant emissions while maintaining high combustion efficiencies and operability. The Flameless Combustion (FC) regime is pointed as one of the promising solutions due to its well-distributed reaction zones that yield low NOx emissions and oscillations. A dual-combustor configuration potentially facilitates the attainment of FC in the Inter-Turbine Burner (ITB). The development of such burner is dependent on knowledge regarding NOx formation and the parameters affecting it. It is known from the literature that the NOx formation mechanisms are different in FC. Therefore, in an attempt to clarify some of the mechanisms involved in NOx formation at relevant conditions, a chemical reactor network model developed to represent the ITB is explored. The role of prompt NOx was previously shown to be dominant at relatively low inlet temperatures and atmospheric pressure. In order to check these findings, five chemical reaction mechanisms were employed. All of them overpredicted NOx emissions and the overprediction is likely to be caused by the prompt NOx subset implemented in these mechanisms. Higher reactants temperatures and operational pressures were also investigated. Overall NOx emissions increased with temperature and the NOx peak moved to lower equivalence ratios. Operational pressure changed the emissions trend with global equivalence ratio. Leaner conditions had behaviour similar to that of conventional combustors (increase in NOx), while NOx dropped with further increase in equivalence ratio due to suppression of the prompt NOx production, as well as an increase in NO reburning. These trends highlight the differences between the emission behaviour of the ITB with those of a conventional combustion system.

There is a growing interest in the use of alternative fuels in gas turbine engines to reduce emissions. Testing of alternative fuels is expensive when done on a large-scale gas turbine engine. In this study, a re-commissioned small gas turbine auxiliary power unit (APU) has been used to test various blends of Jet A-1, synthetic paraffinic kerosene (SPK) and diesel with as well as eight other novel fuels. A detailed analysis of performance, gaseous emissions and particulate emissions has been presented in this study. It is observed that aromatic content in general as well as the particular chemical composition of the aromatic compound plays a vital role in particulate emissions generation. SPK fuel shows substantially lower particulate emissions with respect to Jet A. However, not all the species of aromatics negatively impact particulate emissions. Gaseous emissions measured are comparable for all the fuels tested in this study.