Hostname: page-component-7b7567c8c-2n9c9 Total loading time: 0 Render date: 2026-11-17T00:21:38.365Z Has data issue: false hasContentIssue false

NUMERICAL SIMULATIONS FOR LARGELY DEFORMED BEAMS AND RINGS ADOPTING A NONTENSILE SMOOTHED PARTICLE HYDRODYNAMICS ALGORITHM

Published online by Cambridge University Press:  15 August 2023

THIEN TRAN-DUC
Affiliation:
School of Information and Physical Sciences, The University of Newcastle, Callaghan, NSW 2308, Australia; e-mail: thien.tranduc@newcastle.edu.au, natalie.thamwattana@newcastle.edu.au
MICHAEL H. MEYLAN*
Affiliation:
School of Information and Physical Sciences, The University of Newcastle, Callaghan, NSW 2308, Australia; e-mail: thien.tranduc@newcastle.edu.au, natalie.thamwattana@newcastle.edu.au
NGAMTA THAMWATTANA
Affiliation:
School of Information and Physical Sciences, The University of Newcastle, Callaghan, NSW 2308, Australia; e-mail: thien.tranduc@newcastle.edu.au, natalie.thamwattana@newcastle.edu.au
Rights & Permissions [Opens in a new window]

Abstract

Three typical elastic problems, including beam bending, truss extension and compression, and two-rings collision are simulated with smoothed particle hydrodynamics (SPH) using Lagrangian and Eulerian algorithms. A contact-force model for elastic collisions and equation of state for pressure arising in colliding elastic bodies are also analytically derived. Numerical validations, on using the corresponding theoretical models, are carried out for the beam bending, truss extension and compression simulations. Numerical instabilities caused by largely deformed particle configurations in finite/large elastic deformations are analysed. The numerical experiments show that the algorithms handle small deformations well, but only the Lagrangian algorithm can handle large elastic deformations. The numerical results obtained from the Lagrangian algorithm also show a good agreement with the theoretical values.

Information

Type
Research Article
Creative Commons
Creative Common License - CCCreative Common License - BY
This is an Open Access article, distributed under the terms of the Creative Commons Attribution licence (https://creativecommons.org/licenses/by/4.0), which permits unrestricted re-use, distribution and reproduction, provided the original article is properly cited.
Copyright
© The Author(s), 2023. Published by Cambridge University Press on behalf of Australian Mathematical Publishing Association Inc.
Figure 0

Figure 1Demonstration for an elastic collision of two SPH particles.

Figure 1

Figure 2Bending of a cantilever beam simulated using the CCB-SPH algorithm. The beam has length $L=0.2$ m, thickness $H=2$ cm and Young’s modulus $E=20$ GPa. A vertical load $F_y=-250$ N is applied downward at its free end.

Figure 2

Figure 3Bending of a cantilever beam simulated using the CCBWAT-SPH algorithm. The beam has length $L=0.2$ m, thickness $H=2$ cm and Young’s modulus $E=20$ GPa. A vertical load $F_y=-250$ N is applied downward at its free end. The values of the parameters of the artificial stress terms are $a=1$, $\epsilon =0.3$ and $n=6$.

Figure 3

Figure 4Bending of a cantilever beam simulated using the ICB-SPH algorithm. The beam has length $L=0.2$ m, thickness $H=2$ cm and Young’s modulus $E=20$ GPa. A vertical load $F_y=-250$ N is applied downward at its free end.

Figure 4

Table 1Vertical and horizontal deflections of a bent cantilever beam ($L=0.2$ m, $H=2$ cm and ${E=20}$ GPa) under various load scenarios, from $-10$ N to $-250$ N. The values are obtained from simulations adopting the CCB-SPH, CCBWAT-SPH and ICB-SPH algorithms, and the theoretical model, equations (3.1)–(3.3), for a beam with finite deflections.

Figure 5

Table 2Numerical convergence for various spatial resolutions ($\triangle x$) for the case of cantilever beam bending. The relative errors compared with their corresponding theoretical values for the horizontal ($\delta _h$) and vertical ($\delta _v$) displacements of the free end are shown for the spatial resolution varied from $5$ mm down to $0.5$ mm.

Figure 6

Figure 5Stretch deformation of the cantilever beam ($L=0.2$ m, $H=5$ cm and $E=2$ GPa) under an axial force $F=3000$ N simulated using the CCB-SPH, CCBWAT-SPH and ICB-SPH algorithms.

Figure 7

Figure 6Stretch deformation of the cantilever beam ($L=0.2$ m, $H=5$ cm and $E=2$ GPa) under an axial force $F=7000$ N simulated using the CCB-SPH, CCBWAT-SPh and ICB-SPH algorithms.

Figure 8

Table 3Horizontal displacement of the cantilever beam ($L=0.2$ m, $H=5$ cm and $E=2$ GPa) under various tension/compression scenarios in comparison to the theoretical values obtained using equation (3.4). The simulations adopt the CCB-SPH, CCBWAT-SPH and ICB-SPH algorithms.

Figure 9

Table 4Numerical convergence for various spatial resolutions ($\triangle x$) for the beam pure stretch and compression. The relative errors compared with their corresponding theoretical values for the horizontal displacement ($\delta _h$) at the free end are presented for the spatial resolution varied from $10$ mm down to $0.5$ mm.

Figure 10

Figure 7Collision of two elastic rings, each of which has a similar diameter of $0.2$ m, thickness of $1$ cm, Young’s modulus of $20$ GPa and moves at a constant velocity $v_r=5$ m/s, are simulated using the CCB-SPH algorithm.

Figure 11

Figure 8Collision of two elastic rings, each of which has a similar diameter of $0.2$ m, thickness of $1$ cm, Young’s modulus of $20$ GPa and moves at a constant velocity $v_r=5 $ m/s, is simulated using the CCBWAT-SPH algorithm.

Figure 12

Figure 9Collision of two elastic rings, each of which has a similar diameter of $0.2$ m, thickness of $1$ cm, Young’s modulus of $20$ GPa and moves at a constant velocity $v_r=5$ m/s, is simulated using the ICB-SPH algorithm.

Figure 13

Figure 10Collision of two elastic rings, each of which has a similar diameter of $0.2$ m, thickness of $1$ cm, Young’s modulus of $20$ GPa and moves at a constant velocity $v_r=$ 8 m/s, is simulated using the ICB-SPH algorithm.