Hostname: page-component-7b7567c8c-7pwfn Total loading time: 0 Render date: 2026-11-16T19:42:26.503Z Has data issue: false hasContentIssue false

On the bead design in LFT structures: the influence of manufacturing-induced residual stresses

Published online by Cambridge University Press:  18 March 2021

Sven Revfi*
Affiliation:
IPEK – Institute of Product Engineering, Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
Marvin Mikus
Affiliation:
IPEK – Institute of Product Engineering, Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
Kamran Behdinan
Affiliation:
Department of Mechanical & Industrial Engineering, University of Toronto, Toronto, ON, Canada
Albert Albers
Affiliation:
IPEK – Institute of Product Engineering, Karlsruhe Institute of Technology (KIT), Karlsruhe, Germany
*
Corresponding author Sven Revfi sven.revfi@kit.edu
Rights & Permissions [Opens in a new window]

Abstract

In the design of long fibre reinforced thermoplastic (LFT) structures, there is a direct dependency on the manufacturing. Therefore, it is indispensable to integrate the manufacturing influences into the design process. This not only offers new opportunities for material- and load-adapted designs, but also reduces cost-intensive modifications in later stages. The goal of this contribution is to make the complexity manageable by presenting a method which couples LFT manufacturing and structural simulations in an automated optimization loop. Herein, the influence of linear-elastic, local anisotropic material properties as well as residual stresses resulting from the compression molding of LFT on the stiffness-optimized design of beaded plates is investigated. Based on the simulation studies in this contribution, it can be summarized that the resulting bead height and flank angle, considering anisotropies and residual stresses, are smaller compared to isotropic modelling. As a conclusion, the strength constraint limits the maximum bead height and the flank angle needs to be additionally chosen as a consequence of the local fibre orientations and residual stresses resulting from manufacturing. Optimized bead cross sections are only valid for a specific system under investigation, as they depend on the defined boundary conditions (load case, initial charge geometry and position, fibre orientations, etc.).

Information

Type
Research Article
Creative Commons
Creative Common License - CCCreative Common License - BY
This is an Open Access article, distributed under the terms of the Creative Commons Attribution licence (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted re-use, distribution, and reproduction in any medium, provided the original work is properly cited.
Copyright
© The Author(s), 2021. Published by Cambridge University Press
Figure 0

Figure 1.(a) Controller-based and (b) sensitivity-based bead optimization result for a one-sided clamped plate under bending load.

Figure 1

Figure 2.Bead cross section and bead parameters according to Emmrich (2004).

Figure 2

Figure 3.Coupling diagram for the optimization of manufacturing-based beads in fibre reinforced polymers considering residual stresses from the manufacturing process.

Figure 3

Figure 4.Two-stage mapping exemplary for three layers in thickness direction (Revfi, Spadinger, & Albers 2019).

Figure 4

Figure 5.(a) Design area (b) bead partitions and trajectories according to Revfi et al. (2019) (c) schematic bead generation via perpendicular nodal displacement.

Figure 5

Figure 6.Meshed plate (yellow) and initial charge (orange) (Revfi et al.2020).

Figure 6

Table 1.Additional modelling settings

Figure 7

Figure 7.Model with boundary conditions: one-sided clamped plate (Revfi et al.2020).

Figure 8

Figure 8.Residual stress-induced deformation state before the application of the external load, displacement in Z-direction (scale factor: 10).

Figure 9

Table 2.Bead parameter range

Figure 10

Table 3.Strength values

Figure 11

Table 4.Selected individuals of the isotropic optimization – optimum highlighted in bold

Figure 12

Table 5.Selected individuals of the anisotropic optimization without residual stresses – optimum highlighted in bold, further investigated individuals highlighted in italics

Figure 13

Figure 9.Fibre orientation tensor: A22 component indicating vertical fibre orientation (Y-axis). (a) 81° (optimum), (b) 79° and (c) 83°.

Figure 14

Figure 10.(a) Fibre angle dependence of the Young’s modulus according to Roos, Maile, & Seidenfuß (2017). (b) Number of elements with fibres in the angle difference to the first principal stress for three geometries with different flank angles.

Figure 15

Table 6.Selected individuals of the anisotropic optimization with residual stresses – optimum highlighted in bold

Figure 16

Figure 11.Residual stress states per flank angle (a) 76° (optimum), (b) 77°, (c) 78° and (d) 75°, and in red the element which has the highest stress in the loaded state and leads to failure at 77°.

Figure 17

Figure 12.Warpage resulting from residual stresses as displacement in Z-direction (scale factor: 10) exemplarily shown for the 76° flank angle geometry (optimum).