Hostname: page-component-7b7567c8c-jswmv Total loading time: 0 Render date: 2026-11-15T23:10:26.551Z Has data issue: false hasContentIssue false

Ultra-compact post-compressor on-shot wavefront measurement for beam correction at PHELIX

Published online by Cambridge University Press:  21 April 2022

J. B. Ohland*
Affiliation:
GSI Helmholtzzentrum für Schwerionenforschung, 64291 Darmstadt, GermanyInstitute for Applied Physics, Technische Universität Darmstadt, 64289 Darmstadt, Germany
U. Eisenbarth
Affiliation:
GSI Helmholtzzentrum für Schwerionenforschung, 64291 Darmstadt, Germany
B. Zielbauer
Affiliation:
GSI Helmholtzzentrum für Schwerionenforschung, 64291 Darmstadt, Germany
Y. Zobus
Affiliation:
GSI Helmholtzzentrum für Schwerionenforschung, 64291 Darmstadt, GermanyInstitute of Nuclear Physics, Technische Universität Darmstadt, 64289 Darmstadt, Germany
D. Posor
Affiliation:
GSI Helmholtzzentrum für Schwerionenforschung, 64291 Darmstadt, GermanyInstitute for Applied Physics, Technische Universität Darmstadt, 64289 Darmstadt, Germany
J. Hornung
Affiliation:
GSI Helmholtzzentrum für Schwerionenforschung, 64291 Darmstadt, Germany
D. Reemts
Affiliation:
GSI Helmholtzzentrum für Schwerionenforschung, 64291 Darmstadt, Germany
V. Bagnoud
Affiliation:
GSI Helmholtzzentrum für Schwerionenforschung, 64291 Darmstadt, GermanyInstitute for Applied Physics, Technische Universität Darmstadt, 64289 Darmstadt, GermanyHelmholtz-Institut Jena, 07743 Jena, Germany
*
Correspondence to: J. B. Ohland, GSI Helmholtzzentrum für Schwerionenforschung, Planckstraße 1, 64291 Darmstadt, Germany. Email: j.b.ohland@gsi.de

Abstract

In order to reach the highest intensities, modern laser systems use adaptive optics to control their beam quality. Ideally, the focal spot is optimized after the compression stage of the system in order to avoid spatio-temporal couplings. This also requires a wavefront sensor after the compressor, which should be able to measure the wavefront on-shot. At PHELIX, we have developed an ultra-compact post-compressor beam diagnostic due to strict space constraints, measuring the wavefront over the full aperture of 28 cm. This system features all-reflective imaging beam transport and a high dynamic range in order to measure the wavefront in alignment mode as well as on shot.

Information

Type
Research Article
Creative Commons
Creative Common License - CCCreative Common License - BY
This is an Open Access article, distributed under the terms of the Creative Commons Attribution licence (https://creativecommons.org/licenses/by/4.0/), which permits unrestricted re-use, distribution, and reproduction in any medium, provided the original work is properly cited.
Copyright
© The Author(s), 2022. Published by Cambridge University Press in association with Chinese Laser Press
Figure 0

Figure 1Scale sketch of the PHELIX target area before the installation of the PTAS. The DM will be placed in the compressor area to the right, while the available space for the PTAS is indicated by the ruled area on the left. The light gray region indicates the area reserved for user equipment and personnel access.

Figure 1

Figure 2Scale schematic of the PTAS. The intermediate focal diagnostic is not shown for clarity. The other main components are labeled (‘L’ for lenses) and described in the text.

Figure 2

Figure 3The NF (left) and absolute, uncorrected WF (right) at the PTAS, recorded on-shot using the largest possible aperture.

Figure 3

Figure 4An etched tungsten needle is used to mark the position of the focal spot (center). A bit of dust has stuck on its tip. The large caustics are created by backlighting, which is used in order to see the shadow of the needle.

Figure 4

Figure 5Scale schematic of the intermediate focal diagnostic in side view (left) and top view (right), observing the backwards propagating alignment beam. The needle and the diagnostic mirrors can be moved in and out of the beam, while the microscope can be moved in three axes in order to change the viewing position. The other possible states of the diagnostic are drawn as transparent overlays.

Figure 5

Figure 6Schematic of the CLAWS concept.

Figure 6

Figure 7Sketch of the target chamber area, indicating a possible configuration during the calibration routine.

Figure 7

Figure 8The unoptimized (left) and optimized (right) focal spots of a copper OAP at the target position, recorded with a 16-bit CMOS camera, installed in CLAWS. The intensity is estimated for a 100 J, 500 fs pulse.

Figure 8

Figure 9The encircled energy over the radius from the point of largest intensity, taken for the focuses shown in Figure 8.

Figure 9

Figure 10The unoptimized (left) and optimized (right) WFs corresponding to the focuses shown in Figure 8, recorded using CLAWS. The WFs are measured relative to the reference generated using the pinhole. The unoptimized WF features an RMS of 0.202$\lambda$, while it is reduced to 0.052$\lambda$ after optimization.

Figure 10

Figure 11A sketch of the PHELIX compressor, including the gratings, the DM and the directions to the compressor beam sensor (‘COS’) and the PTAS.

Figure 11

Figure 12A qualitative comparison between FFs (a) measured at the compressor exit and (b) measured at the PTAS at the same time. No beam correction was applied.

Figure 12

Figure 13Transparency of the polystyrene foil targets, plotted over their thickness. The estimated intensities are color coded, while different shot configurations are indicated by the shape of the data points. The data set displayed as triangles was taken from a previous beam time (P155).