Hostname: page-component-7b7567c8c-fvjsw Total loading time: 0 Render date: 2026-11-17T15:45:24.321Z Has data issue: false hasContentIssue false

A compact UWB antenna with dynamically switchable band-notched characteristic using broadband rectenna and DC-DC booster

Published online by Cambridge University Press:  02 February 2021

Mohammad M. Fakharian*
Affiliation:
Faculty of Engineering, University of Garmsar, Garmsar, Iran
*
Author for correspondence: Mohammad M. Fakharian, E-mail: fakharian@fmgarmsar.ac.ir
Rights & Permissions [Opens in a new window]

Abstract

In this article, a dynamically switchable ultra-wideband (UWB) planar monopole antenna employing defected ground structure (DGS) with a folded stepped impedance resonator (SIR) that can operate as either a UWB mode or the single band-notched mode is introduced. The UWB monopole antenna contains a novel whirligig-shaped radiating patch and a chambered conductor as a partial ground plane. The switchable UWB antenna uses one PIN diode as switching elements in the DGS-SIR structure without any biasing network. When the state of diode is OFF, the planar monopole antenna changes to the UWB mode, and when the diode is turned ON, a frequency notch is created at 5–6 GHz. The state of diode is set to the “ON” state dynamically in the presence of a 5–6 GHz RF signal that is detected by using a wireless power management unit (PMU) that contains a broadband rectenna and a DC-DC passive booster. The rectenna consists of a novel cypress-shaped monopole antenna as a signal receiving part and two sub-rectifiers which are connected to a 3 dB branch-line coupler with a grounded isolation port. The antenna switches from UWB to single band-notched when an RF input signal (≥8.5 dBm) in the 5.25 GHz is sensed by the RF PMU with a conversion efficiency of 26% and DC output voltage of 0.36 V, and it fades immediately in real time when the external RF signal is eliminated. In the three-tone signals, the efficiency and input signal improvements are about 10% and −5.5 dBm in the low-power levels, especially, and so develop and enhance the performance of the dynamic reconfigurability.

Information

Type
Antenna Design, Modelling and Measurements
Copyright
Copyright © The Author(s), 2021. Published by Cambridge University Press in association with the European Microwave Association
Figure 0

Table 1.Comparison of the proposed work with previous work

Figure 1

Fig. 1.(a) Configuration of the designed switchable band-notch UWB antenna. (b) The fabricated antenna prototype.

Figure 2

Fig. 2.The PIN diode-equivalent RF circuit at the OFF and ON states.

Figure 3

Fig. 3.The surface current distributions on the antenna at 5.5 GHz in the (a) “OFF” state and (b) “ON” state.

Figure 4

Fig. 4.Simulated |S11| characteristics of the band-notched UWB antenna in the OFF state with different values of (a) g, (b) La, and (c) Ws in the folded DGS-SIR.

Figure 5

Fig. 5.Simulated and measured |S11| of the designed band-notched UWB antenna in the ON and OFF states.

Figure 6

Fig. 6.Measured and simulated (a) realized gains and (b) efficiency of the proposed antenna in the OFF and ON states.

Figure 7

Fig. 7.Measured H- and E-plane radiation patterns of the antenna at the ON and OFF state at resonant frequencies of (a) 4.2 GHz and (b) 9.8 GHz.

Figure 8

Fig. 8.The configuration of the designed rectenna (unit: mm). (b) The fabricated rectenna prototype.

Figure 9

Fig. 9.Measured and simulated |S11| comparison of the receiving antenna. The scheme of fabricated antenna is shown in the inset photograph.

Figure 10

Fig. 10.The simulated and measured |S11| of the stand-alone rectifier at three input power levels from −20 to 0 dBm at 5.6 GHz with RL = 2.7 KΩ. The fabricated prototype is shown in the inset photograph.

Figure 11

Fig. 11.The simulated and measured (a) RF-dc conversion efficiency and (b) output voltage of the proposed rectifier versus input power levels at three cases for the load resistance of 2.7 kΩ.

Figure 12

Fig. 12.The simulated RF-dc conversion efficiency of the proposed rectifier versus output load at two cases for different input power levels.

Figure 13

Fig. 13.Circuit diagram of the DC-DC power booster [33]. The fabricated prototype is also shown.

Figure 14

Fig. 14.Measurement setup for dynamically reconfigurable switchable band-notched UWB antenna. The fabricated combined module is also shown.