Hostname: page-component-7b7567c8c-wxvwp Total loading time: 0 Render date: 2026-11-18T00:33:00.740Z Has data issue: false hasContentIssue false

Wideband split-ring antenna arrays based on substrate integrated waveguide for Ka-band applications

Published online by Cambridge University Press:  30 April 2021

Yunfeng Dong*
Affiliation:
Electromagnetic Systems Group, Department of Electrical Engineering, Technical University of Denmark, Oersteds Plads Building 348, 2800 Kgs., Lyngby, Denmark
Vitaliy Zhurbenko
Affiliation:
Electromagnetic Systems Group, Department of Electrical Engineering, Technical University of Denmark, Oersteds Plads Building 348, 2800 Kgs., Lyngby, Denmark
Kyriakos Kaslis
Affiliation:
Electromagnetic Systems Group, Department of Electrical Engineering, Technical University of Denmark, Oersteds Plads Building 348, 2800 Kgs., Lyngby, Denmark
Jeppe M. Bjørstorp
Affiliation:
Electromagnetic Systems Group, Department of Electrical Engineering, Technical University of Denmark, Oersteds Plads Building 348, 2800 Kgs., Lyngby, Denmark
Tom K. Johansen
Affiliation:
Electromagnetic Systems Group, Department of Electrical Engineering, Technical University of Denmark, Oersteds Plads Building 348, 2800 Kgs., Lyngby, Denmark
*
Author for correspondence: Yunfeng Dong, E-mail: yundon@elektro.dtu.dk
Rights & Permissions [Opens in a new window]

Abstract

This paper presents wideband split-ring antenna arrays based on substrate integrated waveguide (SIW) for Ka-band (26.5–40 GHz) applications. The antenna array is fed by a 2.92 mm coaxial connector (K-connector) and the power is equally distributed to each split-ring resonator. The designed coplanar waveguide (CPW), SIW, CPW-to-SIW transition, coaxial-to-CPW transition, and two-stage SIW power divider are described in detail. By using a thin Rogers 6002 substrate with silver epoxy-filled vias, a transition prototype is designed, fabricated, and tested in a back-to-back configuration. A wideband split-ring resonator is developed as a single element and four possible arrangements of antenna arrays are introduced. By combining the designed components and routing paths, two full layouts of the antenna arrays with four split-ring resonators are addressed. As a demonstrator, a 2×2 antenna array prototype in a compact format is designed, fabricated, and tested. The fabricated antenna array achieves a measured directivity of 15.0 dBi with a fractional bandwidth of 23.0% centered at 30.5 GHz.

Information

Type
Antenna Design, Modeling and Measurements
Copyright
Copyright © The Author(s), 2021. Published by Cambridge University Press in association with the European Microwave Association
Figure 0

Fig. 1.CPW based on Rogers 6002 substrate.

Figure 1

Fig. 2.SIW based on Rogers 6002 substrate.

Figure 2

Fig. 3.CPW-to-SIW transition.

Figure 3

Fig. 4.Coaxial-to-CPW transition.

Figure 4

Fig. 5.Transition prototype in a back-to-back configuration.

Figure 5

Fig. 6.Electric field distributions of the designed transition prototype at 28 and 40 GHz.

Figure 6

Fig. 7.Assembly structure and fabrication of the designed transition prototype in a back-to-back configuration.

Figure 7

Fig. 8.Simulation and measurement results of the designed transition prototype in a back-to-back configuration.

Figure 8

Fig. 9.Single-stage SIW power divider.

Figure 9

Fig. 10.Layout of the two-stage SIW power divider and its electric field distribution at 30 GHz.

Figure 10

Fig. 11.Simulation results of the two-stage SIW power divider.

Figure 11

Fig. 12.Layout of the split-ring resonator and its electric field distribution at 30 GHz.

Figure 12

Fig. 13.Radiation pattern (directivity) of the split-ring resonator at 30 GHz.

Figure 13

Fig. 14.Return loss and gain of the split-ring resonator.

Figure 14

Fig. 15.Possible arrangements of four split-ring resonators. (a) 1×4 antenna array (line), (b) 1×4 antenna array (offset), (c) 2×2 antenna array (symmetry), (d) 2×2 antenna array (cross).

Figure 15

Fig. 16.Simulated radiation patterns (directivity) of the antenna arrays with four split-ring resonators at 30 GHz.

Figure 16

Fig. 17.Simulated return losses and directivities (φ = 0°, θ = 0°) of the antenna arrays with four split-ring resonators.

Figure 17

Table 1.Simulated maximum directivities (D0) and half-power beamwidths (HPBWs) of the antenna arrays with four split-ring resonators at 30 GHz.

Figure 18

Fig. 18.Designed SIW antenna arrays with four split-ring resonators: (a) full layout of the 1×4 antenna array (line) with routing paths, (b) full layout of the 2×2 antenna array (symmetry) with routing paths, (c) electric field distribution of the 1×4 antenna array (line) with routing paths at 30 GHz, and (d) electric field distribution of the 2×2 antenna array (symmetry) with routing paths at 30 GHz.

Figure 19

Fig. 19.Full layout of the designed 2×2 antenna array prototype and its electric field distribution at 30 GHz.

Figure 20

Fig. 20.Assembly structure and fabricated 2×2 antenna array prototype.

Figure 21

Fig. 21.Simulated and measured return losses of the designed 2×2 antenna array prototype.

Figure 22

Fig. 22.DTU-ESA Spherical Near-Field Antenna Test Facility for measuring the radiation pattern (directivity) of the fabricated 2×2 antenna array prototype.

Figure 23

Fig. 23.Simulated and measured radiation patterns (directivity) of the designed 2×2 antenna array prototype at 30 GHz.

Figure 24

Fig. 24.Measured co-polarization and cross-polarization directivity components of the designed 2×2 antenna array prototype at 30 GHz.

Figure 25

Table 2.Simulated and measured grating lobe levels of the designed 2×2 antenna array prototype at 30 GHz.

Figure 26

Table 3.Comparison between this work and published SIW antenna arrays at Ka band.