Hostname: page-component-7b7567c8c-2n9c9 Total loading time: 0 Render date: 2026-11-17T09:20:46.672Z Has data issue: false hasContentIssue false

On the compound sessile drops: configuration boundaries and transitions

Published online by Cambridge University Press:  28 April 2021

Chun-Yu Zhang
Affiliation:
Department of Modern Mechanics, University of Science and Technology of China, Hefei 230027, PR China
Peng Gao
Affiliation:
Department of Modern Mechanics, University of Science and Technology of China, Hefei 230027, PR China
Er-Qiang Li
Affiliation:
Department of Modern Mechanics, University of Science and Technology of China, Hefei 230027, PR China
Hang Ding*
Affiliation:
Department of Modern Mechanics, University of Science and Technology of China, Hefei 230027, PR China
*
†Email address for correspondence: hding@ustc.edu.cn

Abstract

The geometry of compound sessile drops at equilibrium on a flat substrate can exhibit a variety of complicated morphological configurations. In this paper, we first investigate the configuration boundaries of the compound sessile drops in a wide parameter space, where a specific configuration is not stable outside its boundaries. Then, we focus on the transitions among the axisymmetric configurations, i.e. encapsulation, lens and collars. The configuration transitions result from the variation of the wettability of the substrate and the volume ratio of the two component droplets. With the help of theoretical analysis and numerical simulations, we obtain previously unidentified criteria for the onset of configuration transition, identify the irreversible and reversible configuration transitions, reveal the dynamic behaviours of configuration transitions that are not accessible to theoretical analysis, and provide a further step towards the ultimate purpose of such work, which is the controllable reconfiguration of the compound sessile drops.

Information

Type
JFM Papers
Copyright
© The Author(s), 2021. Published by Cambridge University Press
Figure 0

Figure 1.Morphological configurations of compound sessile drops resting on a flat substrate: (a) encapsulation, (b) lens, (c) collars and (d) Janus, which are also referred thereafter to as configurations $E$, $L$, $C$ and $J$, respectively. Solid lines represent the surface of the component droplet 1 (made up of fluid 1), while dashed lines represent the surface of the component droplet 2 (made up of fluid 2).

Figure 1

Figure 2.Verification of theoretical predictions of compound sessile drops at equilibrium. (a) Configuration $E$ with $\lambda =0.100$ and $\theta _{23}=70^{\circ }$. (b) Configuration $L$ with $\lambda =0.250$ and $\theta _{23}=80^{\circ }$. (c) Configuration $C$ with $\lambda =0.400$ and $\theta _{23}=70^{\circ }$. (d) Configuration $C$ with $\lambda =0.400$ and $\theta _{23}=100^{\circ }$. Solid lines are the numerical results and dashed lines are the theoretical prediction.

Figure 2

Figure 3.Geometry and configuration boundaries of configuration $C$. Panel (a) shows the general drop shape of configuration $C$ with $\theta _{23}= 80^{\circ }$ and $\lambda =0.500$. The drop shapes at the critical conditions are shown in panel (b) $\theta _{23}=70^{\circ }$ and $\lambda =0.341$ and panel (c) $\theta _{23}= 100^{\circ }$ and $\lambda =0.267$). Panel (d) shows the regime diagram with respect to $\lambda$ and $\theta _{23}$, in which the grey indicates the region where the configuration $C$ is stable. The boundaries are represented by three critical volume ratios: $\lambda _{c,1}$ (at which $r_3$ reaches a minimum value below which there is no solution for configuration $C$), $\lambda _{c,2}$ (at which $r_2$ reaches a minimum value) and $\lambda _{c,3}$ (at which $r_1=r_3$).

Figure 3

Figure 4.Saddle-point bifurcation in the solution of configuration $C$. (a) Contact line position $r_3$ (solid lines) and the rescaled system energy $E_S$ (dashed lines) at $\theta _{23}=70^{\circ }$ as a function of volume ratio $\lambda$. (b) One theoretical prediction of the drop geometry with $\lambda =0.600$ and $r_3=0.601$ (denoted by $\blacksquare$ in panel (a)). (c) The drop geometry at the onset of configuration transition at $\lambda =0.345$ and $r_3=0.233$ (denoted by $\bullet$ in panel (a)). (d) The non-physical theoretical prediction of the drop geometry with $\lambda =0.600$ and $r_3=0.601$ (denoted by $\blacktriangle$ in panel (a)). (e) Temporal evolution of the drop geometry from panel (d) to panel (b) obtained by numerical simulations. The arrow indicates the sequence of the times.

Figure 4

Figure 5.Geometry and configuration boundaries of configuration $E$. Panel (a) shows the drop geometry with $\theta _{23}= 80^{\circ }$ and $\lambda =0.100$, panels (b,c) represent the geometrical criteria for the occurrence of configuration transition, and panel (d) shows the regime diagram with respect to $\lambda$ and $\theta _{23}$, in which the grey indicates the region where the configuration $E$ is stable. The boundaries correspond to the two critical volume ratios: $\lambda _{c,1}$ (solid line) and $\lambda _{c,2}$ (dashed line), respectively.

Figure 5

Figure 6.Geometry and configuration boundaries of configuration $L$. Panel (a) shows the drop geometry with $\theta _{23}= 70^{\circ }$, $\lambda =0.300$, panels (b,c) represent the geometrical criteria for the occurrence of configuration transition at $(\theta _{23}= 70^{\circ }$, $\lambda =0.747$) and $(\theta _{23}= 110^{\circ }$, $\lambda =0.982$), respectively, and panel (d) shows the regime diagram with respect to $\lambda$ and $\theta _{23}$, in which the grey indicates the region where the configuration $L$ is stable. The boundaries correspond to the two critical volume ratios: $\lambda _{c,1}$ (solid line) and $\lambda _{c,2}$ (dashed line), respectively.

Figure 6

Figure 7.Superimposed phase diagrams of configurations $L$, $E$ and $C$ with respect $\lambda$ to $\theta _{23}$.

Figure 7

Figure 8.Geometry of compound sessile drops and transition among the three configurations at $\theta _{23}=80^{\circ }$. (a,b) Configurations $E$ and $L$ at $\lambda =0.100$, respectively; (c,d) configurations $C$ and $L$ at $\lambda =0.307$, respectively; (e,f) configurations $E$ and $L$ at $\lambda =0.497$, respectively; (g,h) configurations $L$ and $C$ at $\lambda =0.911$, respectively; (i) surface energy $E_S$ as a function of $\lambda$.

Figure 8

Figure 9.Snapshots of configuration transition at $\theta _{23}=80^{\circ }$: (a) from $E$ to $C$ at the boundary between zone $V$ and $VI$ ($\lambda =0.497$) at times $t=0$, $1$, $2$, $10$ (from left to right); (b) from $L$ to $C$ at the boundary between zone $VI$ and $VII$ ($\lambda =0.911$) at times $t=0$, $1$, $5$, $20$; and (c) from $C$ to $L$ at the boundary between zone $V$ and $II$ ($\lambda =0.307$) at times $t=0$, $5$, $12.8$, $30$.

Figure 9

Figure 10.Dynamic process of morphological transformation. (a) Snapshots of configuration transitions at the boundary between the zones $I$ and $II$ (specifically, $\theta _{23}=70^{\circ }$ and $\lambda =0.248$) at times $t=0$, $4$, $6.8$, $20$ (from left to right). (b) Snapshots of configuration transition from $C$ to $L$ with $\theta _{23}=110^{\circ }$ and $\lambda =0.360$, at times $t=0$, $2.6$, $5$, $10$. Note that in these cases the transition passes through an intermediate unstable state to reach the configuration at equilibrium.

Figure 10

Figure 11.Dynamic process of morphological transformation. (a) Snapshots of configuration transition from $E$ to $L$ at the boundary between the zones $II$ and $III$ boundary (with $\theta _{23}=110^{\circ }$ and $\lambda =0.229$) at the times $t=0$, $1$, $10$ (from left to right). (b) Snapshots of configuration transition from $L$ to $E$ at the boundary between the zones $IV$ and $VIII$ (with $\theta _{23}=110^{\circ }$ and $\lambda =0.982$) at times $t=0$, $0.2$, $10$ (from left to right). Note that the relative positions of fluid 1 and fluid 2 in the last panels of (a,b) are reversed as compared with the regular configurations in figure 1. Panels (c,d) show the results of configuration transition as predicted by the phase diagram in figure 7, with the same initial conditions as in panel (a) and panel (b), respectively.