Hostname: page-component-7b7567c8c-tnkh4 Total loading time: 0 Render date: 2026-11-16T04:53:42.453Z Has data issue: false hasContentIssue false

Reverse Marangoni surfing

Published online by Cambridge University Press:  15 December 2016

Vahid Vandadi
Affiliation:
Department of Mechanical Engineering, University of Nevada, Reno, NV 89557, USA
Saeed Jafari Kang
Affiliation:
Department of Mechanical Engineering, University of Nevada, Reno, NV 89557, USA
Hassan Masoud*
Affiliation:
Department of Mechanical Engineering, University of Nevada, Reno, NV 89557, USA
*
†Email address for correspondence: hmasoud@unr.edu

Abstract

We theoretically study the surfing motion of chemically and thermally active particles located at a flat liquid–gas interface that sits above a liquid layer of finite depth. The particles’ activity creates and maintains a surface tension gradient resulting in the auto-surfing. It is intuitively perceived that Marangoni surfers propel towards the direction with a higher surface tension. Remarkably, we find that the surfers may propel in the lower surface tension direction depending on their geometry and proximity to the bottom of the liquid layer. In particular, our analytical calculations for Stokes flow and diffusion-dominated scalar fields (i.e. chemical concentration and temperature fields) indicate that spherical particles undergo reverse Marangoni propulsion under confinement whereas disk-shaped surfers always move in the expected direction. We extend our results by proposing an approximate formula for the propulsion speed of oblate spheroidal particles based on the speeds of spheres and disks.

Information

Type
Papers
Copyright
© 2016 Cambridge University Press 
Figure 0

Figure 1.Marangoni propulsion of (a) spherical and (b) disk-shaped particles at a flat interface above a liquid layer of finite depth. The colour maps at the interfaces represent the surface tension distribution stemming either from the discharge of an insoluble agent or from the release of heat by the particle. $S_{i}$ and $l_{p}$ denote, respectively, the liquid–gas interface and three-phase contact line pinned to the particle at a $90^{\circ }$ contact angle. The translation towards the higher surface tension direction is regarded as the forward propulsion.

Figure 1

Figure 2.The normalized propulsion speed $U/U_{\infty }$ as a function of the thickness of the fluid layer $H/R$ for (a) spherical and (b) disk-shaped particles. The squares and circles represent the results for chemically and thermally active particles, respectively. The insets in (a) and (b) show the variation of $\hat{F}_{d}/\hat{F}_{d,\infty }$ (normalized Stokes drag experienced by the particle translating at an interface with no surface tension gradients) versus $H/R$ obtained from the solutions of Ganatos et al. (1980) and Davis (1991). Here, the speed and drag corresponding to a semi-infinite fluid layer ($H/R\rightarrow \infty$) are denoted, respectively, by $U_{\infty }$ and $\hat{F}_{d,\infty }$, whose values for spheres and disks are shown in figure 3. Also, the thin solid line in (a) corresponds to $U=0$.

Figure 2

Figure 3.Comparison between the exact and approximate results for oblate spheroidal particles translating at an interface above a semi-infinite layer of fluid ($H/R\rightarrow \infty$). (a) The variation of non-dimensional drag $\hat{F}_{d,\infty }/\unicode[STIX]{x1D707}\hat{U} R$ versus the particle aspect ratio $\unicode[STIX]{x1D700}$. The dimensionless propulsion speed of (b) chemically and (c) thermally active spheroids (respectively, $U_{\infty }\unicode[STIX]{x1D707}/K_{C}B_{C}$ and $U_{\infty }\unicode[STIX]{x1D707}/K_{T}B_{T}$) as a function of $\unicode[STIX]{x1D700}$. The solid lines represent exact analytical results whereas square symbols depict approximate values obtained via interpolations between the results for spheres and disks. The insets show the relative error of the approximations.

Figure 3

Figure 4.Comparison between the numerical and approximate results for oblate spheroidal particles of aspect ratio $\unicode[STIX]{x1D700}=0.4$. The squares and circles, respectively, represent the relative approximation error $e_{U}$ for the propulsion speed of chemically and thermally active particles at different distances from the wall $H/R$. The inset shows the relative error for the drag $e_{\hat{F}}$ as a function of $H/R$.