Hostname: page-component-7b7567c8c-tnkh4 Total loading time: 0 Render date: 2026-11-16T02:12:44.324Z Has data issue: false hasContentIssue false

Roughness effect in an initially laminar channel flow

Published online by Cambridge University Press:  08 April 2020

N. N. Anika
Affiliation:
School of Mechanical Engineering, The University of Newcastle, NSW 2308, Australia
L. Djenidi*
Affiliation:
School of Mechanical Engineering, The University of Newcastle, NSW 2308, Australia
S. Tardu
Affiliation:
LEGI, Université Grenoble Alpes Domaine Universitaire CS 40700, 38058, Grenoble CEDEX 9, France
*
†Email address for correspondence: lyazid.djenidi@newcastle.edu.au.

Abstract

The possibility of generating and maintaining turbulence in an initially laminar channel flow is investigated for two Reynolds numbers $Re_{b}(=u_{b}h/\unicode[STIX]{x1D708})=880$ and 2100 (based on bulk velocity, $u_{b}$ and half-height of the channel, $h$). The study is carried out through a direct numerical simulation based on the lattice Boltzmann method (LBM). The channel consists of two parallel walls separated by a distance $2h$ where the roughness elements are mounted on both walls. It was observed that when the transverse square bars span half the width of the channel and are mounted in a ‘staggered’ formation, the flow becomes fully turbulent with strong similarities to fully rough wall turbulent channel flows at much higher Reynolds number, as reported in the literature. For example, the rough wall mean velocity profile exhibits a significant downward shift when compared to the smooth wall one. Also, the turbulent kinetic energy budget is similar to its counterpart in rough wall turbulent channel flows at much higher Reynolds numbers than the present ones. It is further shown that the present velocity spectra compared very well with that obtained in a rough wall turbulent boundary layer. Finally, some elements of the possible physical mechanism allowing the generation, growth and sustainability of turbulence are proposed.

Information

Type
JFM Papers
Copyright
© The Author(s), 2020. Published by Cambridge University Press
Figure 0

Figure 1.Schematic of a segment of channel’s configuration with asymmetric rough walls of staggered elements.

Figure 1

Table 1.Channel flow conditions.

Figure 2

Figure 2.Flow visualization based on $\unicode[STIX]{x1D706}_{2}$-contour $(\unicode[STIX]{x1D706}_{2}/\unicode[STIX]{x1D706}_{2,max}=-0.02)$ on staggered rough wall at: (a) $Re_{b}=2093$, (b) $Re_{b}=880$. The section of the channel shown here is $(8\leqslant x/h\leqslant 20)$.

Figure 3

Figure 3.Flow visualization at the entrance of the non-periodic channel flow ($Re_{b}=2093$). Contours of the vorticity magnitude at several heights from the bottom wall, $y/k=0.5$ (a), 1 (b), 1.5 (c), 2, (d), 3 (e) and 4 (f). The three sections of the channel shown here cover the range $1\leqslant x/h\leqslant 19$. On each image, the flow is from left to right. The levels of the vorticity magnitude range from 0 (dark blue) to 0.03 (red).

Figure 4

Figure 4.Flow visualization (non-periodic channel flow, $Re_{b}=2093$): enstrophy contour coloured with the vertical component of the vorticity, $\unicode[STIX]{x1D714}_{y}$, for better visualization effect; the level of the $\unicode[STIX]{x1D714}_{y}$-contours range from $-0.002$ to 0.002. (a) Perspective view; (b) top view. Same range of $x/h$ as in figure 3. Flow is from left to right.

Figure 5

Figure 5.Flow visualization (non-periodic channel flow, $Re_{b}=2093$): enstrophy contour coloured with the vertical component of the vorticity, $\unicode[STIX]{x1D714}_{y}$; same as in perspective view of figure 4 but for $13\leqslant x/h\leqslant 19$.

Figure 6

Figure 6.Contours of $(\unicode[STIX]{x2202}u/\unicode[STIX]{x2202}z)\ast h/u_{b}$ shear layers at the entrance of the non-periodic channel flow ($Re_{b}=2093$). The colour code is as follows: pink, $-1.45$; blue, 1.45. The entry zone is divided into three parts; zone $A$ corresponds to the early transition zone and is delimited by $0\leqslant x/h\leqslant 10$; the zone $B$ is the intermediate transition region wherein the ensemble of transition ingredients take place ($10\leqslant x/h\leqslant 14$) and the turbulent spot appears in $C$, at $x/h\geqslant 14$. Same range of $x/h$ as in figure 3.

Figure 7

Figure 7.Contours of $-(\unicode[STIX]{x2202}w/\unicode[STIX]{x2202}x)\ast h/u_{b}$ shear layers at the entrance of the non-periodic channel flow ($Re_{b}=2093$). The colour code is as follows: pink, $-1.45$; blue, 1.45. Same range of $x/h$ as in figure 6.

Figure 8

Figure 8.Contours of local $(\unicode[STIX]{x2202}(\overline{U}+u)/\unicode[STIX]{x2202}y)\ast h/u_{b}$ shear layers at the entrance of the non-periodic channel flow. ($Re_{b}=2093$) The colour code is as follows: pink, 6.78; blue, $-6.78$. Same range of $x/h$ as in figure 6.

Figure 9

Figure 9.Contours of $\unicode[STIX]{x1D706}_{2}/\unicode[STIX]{x1D706}_{2,min}=0.0035$ at the entrance of the non-periodic channel flow ($Re_{b}=2093$). Same range of $x/h$ as in figure 6.

Figure 10

Figure 10.Contours of local $(\unicode[STIX]{x2202}v/\unicode[STIX]{x2202}z)\ast h/u_{b}$ shear layers at the entrance of the non-periodic channel flow ($Re_{b}=2093$). The colour code is as follows: pink, $-1.45$; blue, 1.45. Same range of $x/h$ as in figure 6.

Figure 11

Figure 11.Contours of $\unicode[STIX]{x1D706}_{2}/\unicode[STIX]{x1D706}_{2,max}=-0.02$ at the entrance of the periodic rough wall channel ($Re_{b}=2093$) for $k/h=0.27$.

Figure 12

Figure 12.Time-averaged flow field in the non-periodic rough wall channel. (a) Contours of $\overline{U}$ (ranging from 0 to $\overline{U}_{c}$; $c$ stands for centreline) in a vertical plane and a horizontal plane just above the roughness base plane; also shown are streamlines behind a roughness element. (b) Top view of the recirculatory motion. (c) Top view of contours of $\overline{W}$ (ranging from $-0.3\overline{U}_{c}$ to $0.3\overline{U}_{c}$) in an horizontal plane at $y/k=0.5$. The flow is from left to right. The last section of the non-periodic channel ($24\leqslant x/h\leqslant 32$) was used to carry out the averaging process.

Figure 13

Figure 13.Time-averaged flow field in the non-periodic rough wall channel. Contours of $\overline{U}$ (ranging from 0 to $\overline{U}_{c}$) in horizontal planes at $y/k=0.125$, 1, 2, 4 and 8, from far left to far right; flow on each image is from left to right. The variation of $\overline{U}$ along a white line (seen in the left image for convenience) is 100 %, 91 %, 34 %, 20 % and 14 % for $y/k=0.125$, 1, 2, 4 and 8, respectively. The last section of the non-periodic channel ($24\leqslant x/h\leqslant 32$) was used to carry out the averaging process.

Figure 14

Figure 14.Time-averaged flow field in the periodic rough wall channel and $k/h=0.27$. (a) Contours of $\overline{U}$ in a vertical plane and a horizontal plane just above the roughness base plane; also shown are streamlines behind a roughness element. (b) Top view of the recirculatory motion. (c) Top view of contours of $\overline{W}$ in an horizontal plane at $y/k=0.5$. The flow is from left to right. The ranges of the $\overline{U}$- and $\overline{W}$-contours are the same as in figure 12.

Figure 15

Figure 15.Time-averaged flow field in the periodic rough wall channel and $k/h=0.27$. Contours of $\overline{U}$ (ranging from 0 to $\overline{U}_{c}$) in horizontal planes at $y/k=0.125$, 1, 2, 3 and 3.71 from far left to far right; flow on each image is from left to right. The ranges of the $\overline{U}$-contours are the same as in figure 12.

Figure 16

Figure 16.Mean velocity profiles normalized by $u_{\unicode[STIX]{x1D70F}}$. Smooth wall, $Re_{b}=999$: – – – –, blue; transverse rough wall, $Re_{b}=1000$: –●–; staggered rough wall, $Re_{b}=880$: ——, blue and $Re_{b}=2093$: ——, black. DNS smooth wall, $Re_{h}=10\,700$: $\cdots \cdots$ (Moser et al.1999). Rough wall, $Re_{b}=4200$, $h/k=0.035$, $p/k=8$: – – – –, black (Krogstad et al.2005); $Re_{b}=4200$, $k/h=0.2$, $p/k=19$: –●– – – and $p/k=8$: –▵– (Leonardi et al.2003). The straight thin solid lines represent the log law. Inset: comparison between time- and space-averaged distribution and the ‘pseudo’ time-averaged ones for $Re_{b}=2093$; $z_{1}$ and $z_{2}$ mark the spanwise locations of the ‘pseudo’ time-averaged profiles.

Figure 17

Figure 17.Present distributions of $\overline{u_{i}^{\prime +2}}$ ($i=1,2$ and 3) for $Re_{b}=880$ (lines with solid circles), $Re_{b}=2093$ (solid lines). Solid lines: present simulations. Dashed, dotted and dash-dotted lines: DNS smooth wall (Moser et al.1999). Blue, $u_{1}^{\prime +2}$; red, $u_{2}^{\prime +2}$; black, $u_{3}^{\prime +2}$. The origin $y/h=0$ for the rough wall data is the base wall and the location $y/k$ represents the location of the roughness crest plane.

Figure 18

Figure 18.Distributions of $\overline{u^{\prime +2}}$, $\overline{v^{\prime +2}}$ and $\overline{w^{\prime +2}}$ for $Re_{b}=2093$ (solid lines). DNS rough wall data of Krogstad et al. (2005): dashed lines. Blue, $u_{1}^{\prime +2}$; red, $u_{2}^{\prime +2}$; black, $u_{3}^{\prime +2}$. The origin $y/h=0$ for the rough wall data is the base wall and the location $y/k=1$ represents the location of the roughness crest plane for the present simulation.

Figure 19

Figure 19.Distributions of $-\overline{(u^{+}v^{+})}$. Symbols: present simulation, $Re_{b}=880$ (blue) and $Re_{b}=2093$ (red). Solid line: smooth wall (Moser et al.1999). Dashed line: rough wall (Krogstad et al.2005). The origin $y/h=0$ is taken at the roughness crest plane.

Figure 20

Figure 20.Correlation coefficient $\unicode[STIX]{x1D70C}_{uv}=\overline{uv}/(u^{\prime }v^{\prime })$. Symbols same as figure 19. Line: rough wall (Krogstad et al.2005). The origin $y/h=0$ is taken at the roughness crest plane.

Figure 21

Figure 21.Turbulent kinetic energy budget, normalized by $u_{\unicode[STIX]{x1D70F}}^{3}/h$, as a function of $y/h$; $Re_{b}=880$ (a) and 2093 (b). Solid line in the top figure: balance of the budget terms in (3.6).

Figure 22

Figure 22.Reproduction of the turbulent kinetic energy budget near the rough wall of Ikeda & Durbin (2007). The budget terms are normalized by $u_{\unicode[STIX]{x1D70F}}^{4}/\unicode[STIX]{x1D708}$; see Ikeda & Durbin (2007) for details on the various symbols.

Figure 23

Figure 23.Turbulent kinetic energy budget for $Re_{b}=2093$, normalized by $u_{\unicode[STIX]{x1D70F}}^{4}/\unicode[STIX]{x1D708}$, as function of $y^{+}=yu_{\unicode[STIX]{x1D70F}}/\unicode[STIX]{x1D708}$ in the vicinity of the lower wall; $y=0$ represents the top plane of the roughness. Lines with symbols: present simulation (same as in figure 21); symbols only: simulation of Leonardi et al. (2006), $k/h=0.1$, $p/k=7$ and $Re_{b}=7000$. Inset: same as main figure but plotted as function of $y/k$.

Figure 24

Figure 24.Kolmogorov-normalized velocity spectra at the channel centreline for $Re_{\unicode[STIX]{x1D706}}\approx 63$ ($Re_{b}=2093$) and $Re_{\unicode[STIX]{x1D706}}\approx 32$ ($Re_{b}=880$). The symbols correspond to the velocity spectrum measured in a rough wall turbulent boundary layer. The asterisk represents Kolmogorov normalization, using either the isotropic expression, $\unicode[STIX]{x1D716}_{iso}$, or the actual one, $\unicode[STIX]{x1D716}_{actual}$, for calculating $\overline{\unicode[STIX]{x1D716}}$.