Hostname: page-component-7b7567c8c-fvjsw Total loading time: 0 Render date: 2026-11-17T04:10:56.804Z Has data issue: false hasContentIssue false

A simple vortex-loop-based model for unsteady rotating wings

Published online by Cambridge University Press:  18 October 2019

Juhi Chowdhury
Affiliation:
Department of Mechanical and Aerospace Engineering, University at Buffalo, The State University of New York, NY 14260, USA
Matthew J. Ringuette*
Affiliation:
Department of Mechanical and Aerospace Engineering, University at Buffalo, The State University of New York, NY 14260, USA
*
†Email address for correspondence: ringum@buffalo.edu

Abstract

An analytical model is developed for the lift force produced by unsteady rotating wings; this configuration is a simple representation of a flapping wing. Modelling this is important for the aerodynamic and control-system design for bio-inspired drones. Such efforts have often been limited to being two-dimensional, semi-empirical, sometimes computationally expensive, or quasi-steady. The current model is unsteady and three-dimensional, yet simple to implement, requiring knowledge of only the wing kinematics and geometry. Rotating wings produce a vortex loop consisting of the root vortex, leading-edge vortex, tip vortex and trailing-edge vortex, which grows with time. This is modelled as a tilted planar loop, geometrically specified by the wing size, orientation and motion. By equating the angular impulse of the vortex loop to that of the fluid volume driven by the wing, the circulatory lift force is derived. Potential flow theory gives the fluid-inertial lift. Adding these two contributions yields the total lift formula. The model shows good agreement with a range of experimental and computational cases. Also, a steady-state lift model is developed that compares well with previous work for various angles of attack.

Information

Type
JFM Papers
Copyright
© 2019 Cambridge University Press 
Figure 0

Figure 1.(a) Schematic of the model wing and its motion, including a ${\mathcal{Q}}^{\ast }=6$ isosurface (Carr et al.2015) to illustrate the real vortex loop. (b) Simplified vortex-loop geometry for the model (top view); the loop arrows give the swirl direction. (c) Experimental visualization to conceptually show the model loop angle ($\unicode[STIX]{x1D703}$).

Figure 1

Figure 2.Experimental results from Carr et al. (2015) for , $\unicode[STIX]{x1D6FC}=45^{\circ }$ and $\unicode[STIX]{x1D6F7}=84^{\circ }$ motivating $\unicode[STIX]{x1D6FC}^{\ast }$. (a) Wing-fixed $x$–$y$ plane velocity vectors at $R$ along the wing span (every other vector is given); a dashed $45^{\circ }$ line is in the near wake for reference. (b) Isosurfaces showing magnitudes of downward velocity and the vortex loop: nested black and translucent grey indicate $v/(R\unicode[STIX]{x1D6FA})=-1.0$ and $-0.9$, respectively; translucent white is ${\mathcal{Q}}^{\ast }=6$.

Figure 2

Table 1.Cases for model validation.

Figure 3

Figure 3.(a) Motion profiles; UB2, UB3 and UB4 overlap. (b) Loop angle variation.

Figure 4

Figure 4.Comparison of the lift coefficient from the $\unicode[STIX]{x1D6FC}=45^{\circ }$ experimental/numerical cases (solid lines) and the model (dashed lines): (a)  and (b) .

Figure 5

Figure 5.(a) Unsteady $C_{L}$ versus  and $\unicode[STIX]{x1D6FC}=60^{\circ }$. (b) Steady-state $C_{L}$ versus $\unicode[STIX]{x1D6FC}$: .

Figure 6

Table 2.Model error based on mean $C_{L}$.

Figure 7

Figure 6.(a) Inertial and circulatory lift coefficients (dashed and solid lines, respectively) for the , $\unicode[STIX]{x1D6FC}=45^{\circ }$ cases. (b) Loop circulation for all cases.

Figure 8

Table 3.Comparison of dimensionless $Ac$ and $A_{ss}c$ for cases with various  and $Ro$.