Hostname: page-component-7b7567c8c-7pwfn Total loading time: 0 Render date: 2026-11-16T05:27:07.437Z Has data issue: false hasContentIssue false

Start-up flow in shallow deformable microchannels

Published online by Cambridge University Press:  27 December 2019

Alejandro Martínez-Calvo*
Affiliation:
Grupo de Mecánica de Fluidos, Departamento de Ingeniería Térmica y de Fluidos, Universidad Carlos III de Madrid, Av. Universidad 30, 28911 Leganés (Madrid), Spain
Alejandro Sevilla
Affiliation:
Grupo de Mecánica de Fluidos, Departamento de Ingeniería Térmica y de Fluidos, Universidad Carlos III de Madrid, Av. Universidad 30, 28911 Leganés (Madrid), Spain
Gunnar G. Peng
Affiliation:
Department of Applied Mathematics and Theoretical Physics, University of Cambridge, Wilberforce Road, CambridgeCB3 0WA, UK
Howard A. Stone
Affiliation:
Department of Mechanical and Aerospace Engineering, Princeton University, Princeton, NJ08544, USA
*
†Email address for correspondence: amcalvo@ing.uc3m.es

Abstract

Microfluidic systems are usually fabricated with soft materials that deform due to the fluid stresses. Recent experimental and theoretical studies on the steady flow in shallow deformable microchannels have shown that the flow rate is a nonlinear function of the pressure drop due to the deformation of the upper soft wall. Here, we extend the steady theory of Christov et al. (J. Fluid Mech., vol. 841, 2018, pp. 267–286) by considering the start-up flow from rest, both in pressure-controlled and in flow-rate-controlled configurations. The characteristic scales and relevant parameters governing the transient flow are first identified, followed by the development of an unsteady lubrication theory assuming that the inertia of the fluid is negligible, and that the upper wall can be modelled as an elastic plate under pure bending satisfying the Kirchhoff–Love equation. The model is governed by two non-geometrical dimensionless numbers: a compliance parameter $\unicode[STIX]{x1D6FD}$, which compares the characteristic displacement of the upper wall with the undeformed channel height, and a parameter $\unicode[STIX]{x1D6FE}$ that compares the inertia of the solid with its flexural rigidity. In the limit of negligible solid inertia, $\unicode[STIX]{x1D6FE}\rightarrow 0$, a quasi-steady model is developed, whereby the fluid pressure satisfies a nonlinear diffusion equation, with $\unicode[STIX]{x1D6FD}$ as the only parameter, which admits a self-similar solution under pressure-controlled conditions. This simplified lubrication description is validated with coupled three-dimensional numerical simulations of the Navier equations for the elastic solid and the Navier–Stokes equations for the fluid. The agreement is very good when the hypotheses behind the model are satisfied. Unexpectedly, we find fair agreement even in cases where the solid and liquid inertia cannot be neglected.

Information

Type
JFM Papers
Copyright
© 2019 Cambridge University Press
Figure 0

Figure 1.Sketch of the flow configuration.

Figure 1

Figure 2.(a) Pressure drop as a function of flow rate extracted from the S4 experiments of Ozsun et al. (2013) (circles), the numerical simulations of Shidhore & Christov (2018) with $\unicode[STIX]{x1D707}=0.91~\text{mPa}~\text{s}$ (red squares), the present numerical simulations considering $\unicode[STIX]{x1D707}=1~\text{mPa}~\text{s}$ with either a linear strain (3.8) (blue triangles) or a nonlinear strain (3.9) (blue crosses), and the corresponding lubrication theory of Christov et al. (2018) for both values of the viscosity (solid lines). The dashed line represents the lubrication solution for rigid channels. (b) Steady 3-D numerical simulation of the S4 system of Ozsun et al. (2013) for an imposed inlet pressure of $\unicode[STIX]{x0394}p=6$ kPa, showing the liquid pressure $p$ and the vertical solid displacement $u_{y}$. All the results have been computed for the geometry described in table 2 using water as working liquid (case II).

Figure 2

Table 1.Characteristic scales used in the derivation of the unsteady lubrication model of § 4.3 (upper row), and the dimensionless parameters that govern the elasto-hydrodynamic problem, deduced in § 4.2 (bottom row).

Figure 3

Table 2.Physical parameters corresponding to the S4 experiment of Ozsun et al. (2013) for two different working liquids, namely water (II), which is the least favourable configuration, and a silicon oil of 500 cSt (I), for which the assumptions of § 4.5 are satisfied. The values of $q_{0}$ and $\unicode[STIX]{x0394}p$ ensure that $\tilde{\unicode[STIX]{x1D6FD}}=0.4$, both in the pressure-controlled case and in the flow-rate-controlled situation.

Figure 4

Figure 3.Self-similar solution for the pressure-controlled case, showing (a) the pressure $P(\unicode[STIX]{x1D701})$ and (b) the rescaled flow rate $\unicode[STIX]{x1D711}(\unicode[STIX]{x1D701})=Q\sqrt{T}$, for different values of $\tilde{\unicode[STIX]{x1D6FD}}$ indicated in the legend.

Figure 5

Figure 4.(a) Inlet flow rate $Q_{0}$ for a pressure-controlled channel and (b) inlet overpressure $P_{0}$ in a flow-rate-controlled configuration, as a function of time $T$, for several values of $\tilde{\unicode[STIX]{x1D6FD}}$ as indicated in the legend. The insets show the solution of Christov et al. (2018) reached at long time (dashed lines). The start-up time $T_{d}$ is shown for (c) a pressure-controlled configuration and for (d) a flow-rate-controlled configuration. The solid lines correspond to the quasi-steady lubrication theory given by equations (4.11)–(4.12c). The symbols correspond to the 3-D numerical simulations for two combinations of the dimensionless parameters $\unicode[STIX]{x1D716}Re$ and $\tilde{\unicode[STIX]{x1D6FE}}$ reported in table 2, and the dashed lines correspond to the asymptotic solution for $\tilde{\unicode[STIX]{x1D6FD}}\ll 1$ obtained in appendix A.

Figure 6

Figure 5.Flow rate $Q(Z,T)$, pressure field $P(Z,T)$ and maximum displacement $\unicode[STIX]{x1D6FD}U_{m}$, as functions of $Z$ for $\tilde{\unicode[STIX]{x1D6FD}}=0.4$ at different times indicated in the legend. The system is pressure driven in (a,c,e), and flow-rate controlled in (b,d,f). The dashed lines show the lubrication solution, and the solid lines the 3-D numerical simulations. Here, $\unicode[STIX]{x1D716}Re/12\simeq 1.9\times 10^{-6}$, $\unicode[STIX]{x1D716}Re/(4\tilde{\unicode[STIX]{x1D6FD}})\simeq 1.42\times 10^{-5}$ and $\tilde{\unicode[STIX]{x1D6FE}}\simeq 2.1\times 10^{-6}$, fulfilling the lubrication hypotheses (case I in table 2). The insets show the self-similar solution given by (4.13), together with the rescaled numerical solution for two different times near start-up.

Figure 7

Figure 6.Same as figure 5, but for $\unicode[STIX]{x1D716}Re/12\simeq 0.46$, $\unicode[STIX]{x1D716}Re/(4\tilde{\unicode[STIX]{x1D6FD}})\simeq 3.45$ and $\tilde{\unicode[STIX]{x1D6FE}}\simeq 0.49$, corresponding to the conditions of the S4 experiment of Ozsun et al. (2013) and case II in table 2.

Figure 8

Figure 7.Colour plot of longitudinal velocity $V_{Z}$ and vertical displacement $\unicode[STIX]{x1D6FD}U_{Y}$ in the $(X,Y)$ plane at a station $Z=0.25$ and times $T=3.5\times 10^{-3}$, $1.8\times 10^{-2}$, $5.3\times 10^{-2}$, $1.4\times 10^{-1}$, $2.8\times 10^{-1}$ and $7.0\times 10^{-1}$, in (a–f), extracted from the quasi-steady lubrication model (4.11)–(4.12c), in (g–l), extracted from 3-D numerical simulations using the linear strain (3.8) and in (m–r) using the nonlinear strain (3.9), for $\tilde{\unicode[STIX]{x1D6FD}}=4.8$ under flow-rate-controlled conditions. The values of the parameters correspond to those of figure 6(b,d,f) (case II in table 2).

Figure 9

Figure 8.Comparison of the inlet flow rate $Q_{0}(T)$ in a pressure-controlled configuration (a) and the inlet overpressure $P_{0}(T)$ in a flow-rate-controlled configuration (b), between numerical computations of (4.11)–(4.12c) and corresponding asymptotic solutions at leading order, equations (A 4a), and (A 4b).