Hostname: page-component-7b7567c8c-z4zkx Total loading time: 0 Render date: 2026-11-16T12:08:09.592Z Has data issue: false hasContentIssue false

Modeling defect cluster evolution in irradiated structural materials: Focus on comparing to high-resolution experimental characterization studies

Published online by Cambridge University Press:  02 March 2015

Brian D. Wirth*
Affiliation:
Department of Nuclear Engineering, University of Tennessee, Knoxville, Tennessee 37996-2300, USA; and Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831, USA
Xunxiang Hu
Affiliation:
Department of Nuclear Engineering, University of Tennessee, Knoxville, Tennessee 37996-2300, USA; and Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831, USA
Aaron Kohnert
Affiliation:
Department of Nuclear Engineering, University of Tennessee, Knoxville, Tennessee 37996-2300, USA
Donghua Xu
Affiliation:
Department of Nuclear Engineering, University of Tennessee, Knoxville, Tennessee 37996-2300, USA
*
a) Address all correspondence to this author. e-mail: bdwirth@utk.edu

Abstract

It is well established that exposure of metallic structural materials to irradiation environments results in significant microstructural evolution, property changes, and performance degradation, which limits the extended operation of current generation light water reactors and restricts the design of advanced fission and fusion reactors. Further, it is well recognized that these irradiation effects are a classic example of inherently multiscale phenomena and that the mix of radiation-induced features formed and the corresponding property degradation depend on a wide range of material and irradiation variables. This inherently multiscale evolution emphasizes the importance of closely integrating models with high-resolution experimental characterization of the evolving radiation-damaged microstructure. This article provides a review of recent models of the defect microstructure evolution in irradiated body-centered cubic materials, which provide good agreement with experimental measurements, and presents some outstanding challenges, which will require coordinated high-resolution characterization and modeling to resolve.

Figure 0

FIG. 1.(a) Illustration of the length and time scales (and feedback) involved in the multiscale processes responsible for microstructural changes in irradiated materials. (b) Illustration of an integrated experimental and computational science-based approach to the multiscale investigation of materials degradation due to high-energy particle irradiation, in which the light orange ellipse highlights the microstructural simulation techniques of OKMC and mean-field reaction-diffusion CD rate theory models, which are the primary focus of this article.

Figure 1

TABLE I.Optimized mobility set to describe the diffusivity (given in terms of prefactor, D0, and activation energy, Em, such that D = D0exp(−Em/kT)) for interstitial clusters/loops and single vacancy in molybdenum, where n refers to the number of interstitials in the cluster of size n.

Figure 2

FIG. 2.Experimental (a, c, and e) and model-predicted (b, d, and f) areal density of observed loops (size greater than 1.3 nm) in molybdenum foils of varying thickness, which were irradiated with 1 MeV Kr ions to a specified flux and fluence at a temperature of approximately 80 °C.

Figure 3

FIG. 3.Comparison of areal density of visible defects from OKMC (open symbols) versus the CD model (solid lines) for three different foil thicknesses at three ion flux levels, (a) 1.6 × 1011, (b) 1.6 × 1010, and (c) 1.6 × 109 ions/cm2/s.

Figure 4

TABLE II.Mobility set to describe the diffusivity (given in terms of prefactor, D0, and activation energy, Em, such that D = D0exp(−Em/kT)) for interstitial clusters and single vacancy for the modeling of neutron irradiated (nominally) pure iron.

Figure 5

FIG. 4.Volumetric density of interstitial (solid) and vacancy (dashed) clusters predicted by the CD model as a function of cluster size (n, # of point defects contained in the cluster) at (a) 60 and (b) 100 °C, as a function of neutron dose (0.01, 0.03, and 0.06 dpa as blue, green, and red, respectively).

Figure 6

FIG. 5.Comparison of modeling predictions (at 60 and 100 °C in green and red, respectively) versus experimental positron measurements of the vacancy cluster size distribution in neutron irradiated iron, as a function of dose in dpa.

Figure 7

FIG. 6.Comparison of CD modeling predictions of (a) interstitial-type dislocation loop density and (b) average size of the visible dislocation loop for four different TEM resolution limits (0.5, 1.0, 1.5, and 2.0 nm) at two different neutron irradiation temperatures for the Fe-a samples, as compared to the TEM observations of Refs. 61 and 62.

Figure 8

FIG. 7.Temperature dependence of the areal defect density as a function of radiation dose for 1 MeV Kr ion irradiation of (a) commercial alloy NF616 (Refs. 66 and 71) and (b) a model ferritic–martensitic steel with nominal composition of Fe–12Cr–0.1C, where the defect density has been normalized to the highest measured density at 50 K.67

Figure 9

FIG. 8.Predicted saturation density of visible defect clusters for 1 MeV Kr ion irradiation of ferritic–martensitic alloys from the CD model with beam activated diffusion implemented in the form of Eq. (11). The experimental data from Fig. 7 (Refs. 66, 67, and 71) are shown for comparison, as normalized to the defect density at 50 K.