Hostname: page-component-7b7567c8c-lpg2g Total loading time: 0 Render date: 2026-11-15T14:27:51.141Z Has data issue: false hasContentIssue false
  • English
  • Français

3-D Modeling of Forced-Flow Thermal-Gradient CVI for Ceramic Composite Fabrication

Published online by Cambridge University Press:  21 February 2011

Thomas L. Starr and
Arlynn W. Smith
Thomas L. Starr
Affiliation:
Georgia Tech Research Institute, Georgia Institute of Technology, Atlanta, GA 30332
Arlynn W. Smith
Affiliation:
Georgia Tech Research Institute, Georgia Institute of Technology, Atlanta, GA 30332
Get access

Abstract

Forced-flow thermal-gradient chemical vapor infiltration (FCVI) has demonstrated excellent potential for fabrication of high strength, high toughness ceramic composites. Extension of this process to large and complex shapes is facilitated by use of a computer model to optimize process conditions and hardware for rapid, uniform infiltration.

A 3-D model has been developed using a “finite volume” formulation. A steady-state solution for heat conduction and Darcy's law permeation produces temperature and gas flow distributions within the fiber preform. These are used to generated matrix deposition rates within each volume element. By “marching” through time, a complete simulation of the densification process can be obtained.

The model is demonstrated for a FCVI system with cylindrical symmetry and compared to experimental results obtained at the Oak Ridge National Laboratory. The model results suggest a self-optimizing feature of the force flow/thermal gradient CVI process that produces uniform density in the final composite over a range of infiltration conditions. This matches experimental observation where good uniformity has been achieved over a wide range of gas flows, pressure and temperature.

Information

Type
Research Article
Information
MRS Online Proceedings Library (OPL) , Volume 168 , 1989, 55
Copyright
Copyright © Materials Research Society 1990

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

1.Caputo, A. J. and Lackey, W. J., U.S. Pat. No. 4,580,524 (8 April 1986).Google Scholar
2.Caputo, A. J. and Lackey, W. J., Oak Ridge National Laboratory report, ORNL/TM-9235, October 1984.Google Scholar
3.Caputo, A. J. and Lackey, W. J., Cer. Eng. Sci. Proc. 5 (7–8), 654–67 (1984).Google Scholar
4.Caputo, A. J., Lackey, W. J., and Stinton, D. P., Cer. Eng. Sci. Proc. 6 (7–8), 694–706 (1985).Google Scholar
5.Caputo, A. J., Stinton, D. P., Lowden, R. A., and Besmann, T. M., Am. Ceram. Soc. Bull. 66 (2), 368–72 (1987).Google Scholar
6.Starr, T. L. in Proceedings of the Conference on Whisker- and Fiber-Toughened Ceramics, edited by Bradley, R. A., et al. (ASM International, Metals Park, Ohio, 1988) pp. 243–252.Google Scholar
7.Patankar, S. V., Numerical Heat Transfer and Fluid Flow (Hemisphere Publishing Corporation, New York, 1980).Google Scholar
8.Pratt, A. W. in Thermal Conductivity, edited by Tye, R. P. (Academic Press, New York, 1969) pp. 301–405.Google Scholar
9.Tawil, H., Bentsen, L. D., Baskaran, S., Hasselman, D. P. H., J. Mat. Sci. 20, 3201–3212 (1985).Google Scholar
10.Freeman, G. B., Starr, T. L. and Elston, T. C., this publication.Google Scholar
11.Satterfield, C. N. and Sherwood, T. K., The Role of Diffusion in Catalysis, (Addison-Wesley Publishing Co., Reading, Massachusetts, 1963).Google Scholar
12.Brennfleck, , Fitzer, E., Schoch, B., Dietrich, M. in Proc. of 9th Int. Conf. on Chemical Vapor Deposition, edited by Cullen, G. W. (The Electrochemical Society, Pennington, New Jersey, 1984) pp. 649–662Google Scholar
13.Lowden, R. A., et al., Oak Ridge National Laboratory report ORNL/TM-10403, May 1987.Google Scholar