Hostname: page-component-7b7567c8c-tnkh4 Total loading time: 0 Render date: 2026-11-17T01:40:00.107Z Has data issue: false hasContentIssue false

Properties and Improved Space Survivability of POSS (Polyhedral Oligomeric Silsesquioxane) Polyimides

Published online by Cambridge University Press:  01 February 2011

Sandra J. Tomczak
Affiliation:
AFRL/PRSM, Materials Applications Branch, Air Force Research Laboratory, 10 E. Saturn Blvd, Bldg. 8451, Edwards AFB, CA 93524, USA
Darrell Marchant
Affiliation:
ERC Incorporated, Materials Applications Branch, Air Force Research Laboratory, 10 East Saturn, Blvd, Bldg 8451, Edwards AFB, CA 93524, USA
Steve Svejda
Affiliation:
AFRL/PRSM, Materials Applications Branch, Air Force Research Laboratory, 10 E. Saturn Blvd, Bldg. 8451, Edwards AFB, CA 93524, USA
Timothy K. Minton
Affiliation:
Department of Chemistry and Biochemistry, Montana State University, 108 Gaines Hall, Bozeman, MT 59717, USA, tminton@montana.edu
Amy L. Brunsvold
Affiliation:
Department of Chemistry and Biochemistry, Montana State University, 108 Gaines Hall, Bozeman, MT 59717, USA, tminton@montana.edu
Irina Gouzman
Affiliation:
Space Environment Section, Soreq NRC, Yavne 81800, Israel
Eitan Grossman
Affiliation:
Space Environment Section, Soreq NRC, Yavne 81800, Israel
George C. Schatz
Affiliation:
Department of Chemistry, Northwestern University, Evanston, IL. 60208–3113 USA, schatz@chem.northwestern.edu
Diego Troya
Affiliation:
Department of Chemistry, Northwestern University, Evanston, IL. 60208–3113 USA, schatz@chem.northwestern.edu
LiPeng Sun
Affiliation:
Department of Chemistry, Northwestern University, Evanston, IL. 60208–3113 USA, schatz@chem.northwestern.edu
Get access

Abstract

Kapton polyimide (PI) is widely used on the exterior of spacecraft as a thermal insulator. Atomic oxygen (AO) in lower earth orbit (LEO) causes severe degradation in Kapton resulting in reduced spacecraft lifetimes. One solution is to coat the polymer surface with SiO2 since this coating is known to impart remarkable oxidation resistance. Imperfections in the SiO2 application process and micrometeoroid / debris impact in orbit damage the SiO2 coating, leading to erosion of Kapton.

A self passivating, self healing silica layer protecting underlying Kapton upon exposure to AO may result from the nanodispersion of silicon and oxygen within the polymer matrix. Polyhedral oligomeric silsesquioxane (POSS) is composed of an inorganic cage structure with a 2:3 Si:O ratio surrounded by tailorable organic groups and is a possible delivery system for nanodispersed silica. A POSS dianiline was copolymerized with pyromellitic dianhydride and 4, 4′-oxydianiline resulting in POSS Kapton Polyimide. The glass transition temperature (Tg) of 5 to 25 weight % POSS Polyimide was determined to be slightly lower, 5 – 10 %, than that of unmodified polyimides (414 °C). Furthermore the room temperature modulus of polyimide is unaffected by POSS, and the modulus at temperatures greater than the Tg of the polyimide is doubled by the incorporation of 20 wt % POSS.

To simulate LEO conditions, POSS PI films underwent exposure to a hyperthermal O-atom beam. Surface analysis of exposed and unexposed films conducted with X-ray photoelectron spectroscopy, atomic force microscopy, and surface profilometry support the formation of a SiO2 self healing passivation layer upon AO exposure. This is exemplified by erosion rates of 10 and 20 weight % POSS PI samples which were 3.7 and 0.98 percent, respectively, of the erosion rate for Kapton H at a fluence of 8.5 × 1020 O atoms cm-2. This data corresponds to an erosion yield for 10 wt % POSS PI of 4.8 % of Kapton H. In a separate exposure, at a fluence of 7.33 × 1020 O atoms cm-2, 25 wt % POSS Polyimide showed the erosion yield of about 1.1 % of that of Kapton H. Also, recently at a lower fluence of 2.03 × 1020 O atoms cm-2, in going from 20 to 25 wt % POSS PI the erosion was decreased by a factor of 2 with an erosion yield too minor to be measured for 25 wt % POSS PI.

Information

Type
Research Article
Copyright
Copyright © Materials Research Society 2005

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable