Hostname: page-component-74656f9884-2dmjx Total loading time: 0 Render date: 2026-11-10T06:06:24.856Z Has data issue: false hasContentIssue false
  • English
  • Français

Development of Biodegradable Polymer Scaffolds Using Co-Extrusion

Published online by Cambridge University Press:  15 March 2011

Newell R. Washburn ,
Carl G. Simon Jr. ,
Alamgir Karim  and
Eric J. Amis
Newell R. Washburn
Affiliation:
National Institute of Standards and Technology, Gaithersburg, MD 20899, USA
Carl G. Simon Jr.
Affiliation:
National Institute of Standards and Technology, Gaithersburg, MD 20899, USA
Alamgir Karim
Affiliation:
National Institute of Standards and Technology, Gaithersburg, MD 20899, USA
Eric J. Amis
Affiliation:
National Institute of Standards and Technology, Gaithersburg, MD 20899, USA
Get access

Abstract

A methodology for the preparation of porous scaffolds for tissue engineering using co-extrusion is presented. Poly(ε-caprolactone) is blended with poly(ethylene oxide) in a twin-screw extruder to form a two-phase material with micrometer-sized domains. Selective dissolution of the poly(ethylene oxide) with water results in a porous material. This method of polymer extrusion permits the preparation of scaffolds having continuous void space and controlled characteristic length scales without the use of potentially toxic organic solvents. A range of blend volume fractions results in co-continuous networks of polymer and void spaces. Annealing studies demonstrate that the characteristic pore size may be increased to larger than 100 μm. The mechanical properties of the scaffolds are characterized by a compressive modulus on the order of 1 MPa at low strains and approximately 10 MPa at higher strains. The results of osteoblast seeding suggest it is possible to use co-extrusion to prepare polymer scaffolds without the introduction of toxic contaminants.

Access options

Get access to the full version of this content by using one of the access options below. (Log in options will check for institutional or personal access. Content may require purchase if you do not have access.)

Article purchase

Temporarily unavailable

References

1. Schugens, Ch., Maquet, V., Grandfils, C., Jerome, R. and Teyssie, Ph., Polymer 37, 1027–1038 (1996).Google Scholar
2. Whang, K., Thomas, C. H., Healy, K. E. and Nuber, G., Polymer 36, 837–842 (1995).Google Scholar
3. Aubert, J. H. and Clough, R. L., Polymer 26, 2047–2055 (1985).Google Scholar
4. Schugens, Ch., Maquet, V., Grandfils, Ch., Jerome, R. and Teyssie, Ph., J. Biomed. Mater. Res. 30, 449–461 (1996).Google Scholar
5. Schugens, Ch., Grandfils, Ch., Jerome, R., Teyssie, Ph., Delree, P., Martin, D., Malgrange, B. and Moonen, G., J. Biomed. Mater. Res. 29, 1349–1362 (1995).Google Scholar
6. Maquet, V. and Jerome, R., Mater. Sci. Forum 250, 15–42 (1997).Google Scholar
7. Washburn, N. R., Simon, C. G., Tona, A., Elgendy, H. M., Karim, A. and Amis, E. J., submitted.Google Scholar
8. Certain equipment and instruments or materials are identified in the paper to adequately specify the experimental details. Such identification does not imply recommendation by the National Institute of Standards and Technology, nor does it imply the materials are necessarily the best available for the purpose.Google Scholar
9. Macosko, C. W., Rheology: principles, measurements, and applications (VCH Publishers, Inc., New York, 1994).Google Scholar
10. Attawia, M.A., Uhrich, K.E., Botchwey, E., Langer, R. and Laurencin, C. T., J. Orthop. Res. 14, 445–454 (1996).Google Scholar
11. Thomson, R. C., Yaszemski, M. J. and Mikos, A. G., in Principles of Tissue Engineering, edited by Lanza, R. P., Langer, R., and Chick, W. L. (Academic Press, San Diego, CA, 1997), pp. 263–272.Google Scholar