Hostname: page-component-7b7567c8c-wxvwp Total loading time: 0 Render date: 2026-11-16T08:11:53.785Z Has data issue: false hasContentIssue false

Impact of a droplet on a flexible lotus-leaf-like disk

Published online by Cambridge University Press:  05 March 2026

Qi Zhang
Affiliation:
School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, PR China
Heng Fu
Affiliation:
School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, PR China
Xinping Zhou*
Affiliation:
School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, PR ChinaState Key Laboratory of Intelligent Manufacturing Equipment and Technology, Huazhong University of Science and Technology, Wuhan 430074, PR China
*
Corresponding author: Xinping Zhou, xpzhou08@hust.edu.cn

Abstract

Flexible substrates are effective in suppressing splashing, but they simultaneously lead to inhibition of spreading (Howland et al. 2016 Phys. Rev. Lett. vol. 117, 184502; Vasileiou et al. 2016 Proc. Natl Acad. Sci. USA vol. 113, pp. 13307−13312). In addition, there has been limited investigation and no established scaling law for the splashing threshold in the case of flexible substrates. To address these points, this paper proposes a lotus-leaf-like disk that can effectively suppress droplet splashing without inhibiting the maximum spreading of droplets. This situation is numerically studied in this paper. Five dynamic modes of the impacting droplet are identified with various Weber numbers (defined as the inertia force relative to the surface tension force) and different disk’s stiffnesses. The threshold Weber number of splashing is developed by considering the flexibility of substrates. Finally, the results demonstrate that the proposed method not only suppresses the splashing but also maintains the maximum spreading.

Information

Type
JFM Papers
Copyright
© The Author(s), 2026. Published by Cambridge University Press
Figure 0

Figure 1.(a) Schematic of a droplet of diameter D0, density ρl and viscosity μl, impacting on a flexible lotus-leaf-like disk consisting of a rigid central circular support and a flexible circular ring with the impact velocity U0 in a downward gravity field. (b) Demonstrates the definitions of two parameters: the spreading factor β which represents the spreading diameter of a droplet on the substrate relative to the diameter of the droplet and the deflection δ at the end of the flexible substrate which represents the deflection relative to the diameter of the droplet.

Figure 1

Figure 2.Maximum spreading factor βmax for different values of We in the present simulations and the experimental results from Vasileiou et al. (2016). The key parameters of the fluids are given as: droplet radius D0 = 2.91 mm, droplet density ρl = 998 kg m−3, droplet dynamic viscosity μl = 0.001 Pa · s, air density ρg = 1.205 kg m−3, air dynamic viscosity μg = 1.825 × 10−5$\rm{Pa} \boldsymbol{\cdot} \rm{s}$ and the surface tension σgl = 0.072 N m−1. The key parameters of the flexible substrate are given as: the thickness hs = 10 μm, the length Ls = 30 mm, the natural frequency fs = 36 Hz and the effective mass ms = kb/(2πfs)2 = 9.5 mg, where kb is the bending stiffness that is directly used for the numerical calculations.

Figure 2

Figure 3.Time variations of the spreading diameter with three different maximum element sizes for We = 50 and K = 0.05.

Figure 3

Figure 4.Snapshots of the morphology of droplet impacting on the substrate for (a) We = 10 and K = 0.01, (b) We = 200 and K = 0.05, (c) We = 500 and K = 10, (d) We = 400 and K = 0.1 and (e) We = 450 and K = 0.01 representing the NSR, NRSD, SSR, SRSD and ARDS modes, respectively. The black arrows are the velocity vector of the droplet. The green arrows are the subsequent movement direction of the substrate.

Figure 4

Figure 5.Distribution of typical modes in a parameter space (K, We). Triangles and circles represent deposition and splashing, respectively. Green triangles, red triangles, blue circles, black circles and the circles (or triangles) with green borders denote the NSR, NRSD, SSR, SRSD and ARDS modes, respectively. The blue dashed line is the splashing threshold Wet,ri for the rigid substrate (Mandre & Brenner 2012). The splashing threshold for large enough K is found to be close to that (Wet,ri = 253, see the Appendix A) for the rigid substrate case (Mandre & Brenner 2012).

Figure 5

Figure 6.Spreading factor β versus the growth time $\varDelta$t for different K at We = 300.

Figure 6

Figure 7.Snapshots of the droplet impacting on the substrate with We = 400 and K = 0.01. Here, α is defined as the angle between the tangent of the substrate near the centre contact area and the horizontal direction.

Figure 7

Figure 8.Energy variation and the spreading factor β plotted against the dimensionless time t with We = 50 for (a) K = 0.05, (b) K = 0.5 and (c) K = 50. (d) The corresponding morphologies of droplets and substrates when the maximum spreading factor is reached (red points in panels a–c) with We = 50 for K = 0.05, K = 0.5 and K = 50, respectively. The grey areas represent the initial spreading stage before reaching the maximum of Ee in panels (a–c).

Figure 8

Figure 9.The time difference between the maximum value of Ee and the splashing.

Figure 9

Figure 10.The effective impact energy versus (a) the initial kinetic energy Ek0 and (b) Ek0/(1 + δmax).

Figure 10

Figure 11.Distribution of typical modes in a parameter space (K, We). The blue dashed line is the splashing threshold Wet,ri for the rigid substrate. The green dash-dotted line is the splashing threshold Wet,fl calculated by (3.3) for the flexible substrate.

Figure 11

Figure 12.Variations of the maximum spreading factor βmax with K for different We.

Figure 12

Figure 13.Variation of the spreading time $\varDelta$tβmax with (a) We for different K and (b) K for different We.

Figure 13

Figure 14.Value of $(\beta _{\textit{max}}^{2}-\beta _{\boldsymbol{v}\rightarrow 0}^{2})^{1/2}{\textit{Re}}^{-1/5}$as a function of We for different stiffnesses K. The solid line is plotted by (3.4).