Hostname: page-component-7b7567c8c-wxvwp Total loading time: 0 Render date: 2026-11-16T05:23:03.933Z Has data issue: false hasContentIssue false

Self-similar dynamics of two-phase flows injected into a confined porous layer

Published online by Cambridge University Press:  02 September 2019

Zhong Zheng*
Affiliation:
Department of Applied Mathematics and Theoretical Physics, University of Cambridge, Cambridge CB3 0WA, UKBP Institute, University of Cambridge, CambridgeCB3 0EZ, UKDepartment of Earth Sciences, University of Cambridge, Cambridge CB3 0EZ, UKSichuan Energy Internet Research Institute, Tsinghua University, Chengdu 610213, ChinaEnergy Strategy and Low-Carbon Development Research Center, Sichuan Energy Internet Research Institute, Tsinghua University, Chengdu 610213, China
Jerome A. Neufeld
Affiliation:
Department of Applied Mathematics and Theoretical Physics, University of Cambridge, Cambridge CB3 0WA, UKBP Institute, University of Cambridge, CambridgeCB3 0EZ, UKDepartment of Earth Sciences, University of Cambridge, Cambridge CB3 0EZ, UK
*
†Email address for correspondence: zzheng@alumni.princeton.edu

Abstract

We study the dynamics of two-phase flows injected into a confined porous layer. A model is derived to describe the evolution of the fluid–fluid interface, where the effective saturation of the injected fluid is zero. The flow is driven by pressure gradients due to injection, the buoyancy due to density contrasts and the interfacial tension between the injected and ambient fluids. The saturation field is then computed after the interface evolution is obtained. The results demonstrate that the flow behaviour evolves from early-time unconfined to late-time confined behaviours. In particular, at early times, the influence of capillary forces drives fluid flow and produces a new self-similar spreading behaviour in the unconfined limit that is distinct from the gravity current solution. At late times, we obtain two new similarity solutions, a modified shock solution and a compound wave solution, in addition to the rarefaction and shock solutions in the sharp-interface limit. A schematic regime diagram is also provided, which summarises all possible similarity solutions and the time transitions between them for the partially saturating flows resulting from fluid injection into a confined porous layer. Three dimensionless control parameters are identified and their influence on the fluid flow is also discussed, including the viscosity ratio, the pore-size distribution and the relative contributions of capillary and buoyancy forces. To underline the relevance of our results, we also briefly describe the implications of the two-phase flow model to the geological storage of $\text{CO}_{2}$, using representative geological parameters from the Sleipner and In Salah sites.

Information

Type
JFM Papers
Copyright
© 2019 Cambridge University Press 
Figure 0

Figure 1.Capillary pressure in (a) and relative permeability curves in (b). The symbols in (b) are representative values of relative permeabilities taken from a geological $\text{CO}_{2}$ sequestration projects (e.g. Bennion & Bachu 2005; Li & Horne 2006), and the curves represent best power-law fitting results in (2.7) with $k_{rn0}=0.116$ and $\unicode[STIX]{x1D6FC}=\unicode[STIX]{x1D6FD}=2$ (Bennion & Bachu 2005; Golding et al.2011).

Figure 1

Figure 2.Schematic of the injection of a non-wetting fluid into a confined porous layer initially saturated with a wetting fluid: (a) shows the saturation field of the injected fluid; (b) illustrates that the interface $h(x,t)$ is defined as the location where the effective saturation of the injected non-wetting fluid $s(x,z,t)=0$, and $x_{f}(t)$ denotes the location of the propagating front.

Figure 2

Table 1.Three dimensionless control parameters are identified: the modified viscosity ratio $N$, rescaled capillary length $H_{e}$ and pore-size distribution parameter $\unicode[STIX]{x1D6EC}$.

Figure 3

Figure 3.Representative calculations for the evolution of the profile shape (black curves) and the saturation field: (a) for $N=2,\unicode[STIX]{x1D6EC}=2,H_{e}=1/5$ and (b) for $N=2,\unicode[STIX]{x1D6EC}=2,H_{e}=1$. The evolution of the interface shape $H(X,T)$, obtained from numerical solutions of (3.4), indicates a transition from early-time unconfined to late-time confined flow behaviours. Once the interface shape is obtained, the saturation field is calculated based on (3.10).

Figure 4

Figure 4.Influence of $\unicode[STIX]{x1D6EC}$ and $H_{e}$ on the saturation field based on (3.10) with $H=1/2$ as an example. (a) $H_{e}=1$ and $\unicode[STIX]{x1D6EC}=\{1,2,10,100\}$ and (b) for $\unicode[STIX]{x1D6EC}=1$ and $H_{e}=\{1/100,1/10,1,2\}$. As $H_{e}\rightarrow \infty$ or $\unicode[STIX]{x1D6EC}\rightarrow 0^{+}$, the saturation field approaches the sharp-interface limit.

Figure 5

Figure 5.Early-time self-similar solutions: (a) strong capillary regime (§ 3.3.1) and (b) weak capillary regime (§ 3.3.2). The solid curves represent the numerical calculations of the similarity solutions. The dashed curves represent the asymptotic shapes near the front of the two-phase gravity current, i.e. solution (3.16) in (a) and (3.23) in (b).

Figure 6

Figure 6.The saturation field (3.19) in the early-time strong capillarity regime: (a) $\unicode[STIX]{x1D6EC}=2$ and $T/H_{e}^{3}=\{10^{-7},10^{-5},10^{-3}\}$; (b) $\unicode[STIX]{x1D6EC}=20$ and $T/H_{e}^{3}=\{10^{-7},10^{-5},10^{-3}\}$. A smaller $T/H_{e}^{3}$ corresponds to stronger capillary effects while a smaller $\unicode[STIX]{x1D6EC}$ corresponds to a more polydisperse pore-size distribution. Both the effects of capillary forces and polydisperse pore size reduce the saturation of the injected fluid, as demonstrated here.

Figure 7

Figure 7.Influence of $\unicode[STIX]{x1D6EC}$ and $H_{e}$ on the inlet height $H_{i}$ at the origin. The asymptotic solutions (3.28a) as $H_{e}\rightarrow 0^{+}$ or $\unicode[STIX]{x1D6EC}\rightarrow \infty$, and (3.28b) as $H_{e}\rightarrow \infty$ or $\unicode[STIX]{x1D6EC}\rightarrow 0^{+}$ are also shown as the dash-dotted and dotted curves, respectively.

Figure 8

Figure 8.Late-time similarity solutions for $N=1/5$: (a) shock solution (3.30) in the sharp-interface limit, and (b) modified shock solution with height $H_{s}=H_{i}\approx 0.934<1$ and front location $\unicode[STIX]{x1D701}_{s}\approx 1.30$. The saturation field is also computed according to (3.10) and shown next to the similarity solutions.

Figure 9

Figure 9.Late-time similarity solutions for $N=2$, $\unicode[STIX]{x1D6EC}=2$ and $H_{e}=\{1/5,1\}$: (a) rarefaction solution (3.32) in the sharp-interface limit, (b) compound wave solution with $H_{i}\approx 0.934$, $H_{s}\approx 0.414$ and $\unicode[STIX]{x1D701}_{s}\approx 1.59$ and (c) modified shock solution with $H_{s}=H_{i}\approx 0.731<1$ and front location $\unicode[STIX]{x1D701}_{s}\approx 3.24$. The saturation field is also computed according to (3.10) and shown next to the similarity solutions.

Figure 10

Figure 10.Representative flux functions $\unicode[STIX]{x1D701}=F(H)$, as defined in (3.34), for different $N$, $\unicode[STIX]{x1D6EC}$ and $H_{e}$. The corresponding flux functions in the sharp-interface limit, based on (3.29), are plotted as the dashed curve. (a) With $N=2$ and $\unicode[STIX]{x1D6EC}=2$, $F(H)$ is non-monotonic for $H_{e}=\{1/1000,1/5\}$ while increases monotonically for $H_{e}=1$. (b) With $N=1/2$ and $\unicode[STIX]{x1D6EC}=2$, $F(H)$ increases monotonically for all $H_{e}$. The flux functions with the same viscosity ratio $N$ in the sharp-interface limit are also plotted in both (a) and (b).

Figure 11

Figure 11.The location of the shock front is determined such that the amount of injected fluid in the shaded area satisfies the global mass constraint (3.35). Three scenarios are demonstrated here: (a) a compound wave solution for a non-monotonic flux function $F(H)$, (b) a modified shock solution from a non-monotonic $F(H)$ and (c) a modified shock solution from a monotonically increasing $F(H)$.

Figure 12

Figure 12.Influence of $N$ on the height and location of the shock front, $H_{s}$ and $\unicode[STIX]{x1D701}_{s}$, respectively. We set $H_{e}=1$ and $\unicode[STIX]{x1D6EC}=2$ in this example. Two regimes are identified for either a compound wave or modified shock solution, separated by a critical viscosity ratio $N\approx 3.32$ as the regime boundary.

Figure 13

Figure 13.Influence of $H_{e}$ on the height $H_{s}$ and location $\unicode[STIX]{x1D701}_{s}$ of the shock front. We set $N=2$ and $\unicode[STIX]{x1D6EC}=2$ in this example, and identify two regimes that correspond to either a compound wave a modified shock solution. A critical capillary length $H_{e}\approx 0.63$, which sets the regime boundary, is calculated for this example.

Figure 14

Table 2.Summary of control parameters and asymptotic behaviours for solutions to (3.4) in § 4. Here $X_{f}$ is the front location, $H_{f}$ is the vertical extent of the interface and $H_{i}$ is the time-independent inlet thickness at late times. For early-time unconfined flows, ‘C’ represents a capillarity similarity solution (§ 3.3.1) and ‘B’ represents a buoyancy similarity solution (§ 3.3.2). For late-time confined flows, ‘CW’ represents a compound wave solution (§ 3.4) and ‘MS’ represents a modified shock solution (§ 3.4).

Figure 15

Figure 14.Evolution of the front location $X_{f}(T)$ in (a) and vertical extent of the interface $H_{f}(T)$ in (b) for $N=2$, $\unicode[STIX]{x1D6EC}=2$ and $H_{e}=1/1000$. Numerical solutions are shown as dots, while the early-time and late-time self-similar solutions are shown as straight lines. The insets in (b) are the profiles at different representative times $T=\{10^{-14},10^{-4},10^{3}\}$ from the numerical solutions.

Figure 16

Figure 15.Evolution of the rescaled profile shapes with $N=2$, $\unicode[STIX]{x1D6EC}=2$ and $H_{e}=1/1000$. The PDE numerical simulation departs from the capillarity similarity solution of (3.15) in the early-time period in (a), approaches the buoyancy similarity solution (3.22) at intermediate times in (b), before eventually approaches the confined similarity solution in the late-time period in (c).

Figure 17

Figure 16.Evolution of the front location $X_{f}(T)$ in (a), vertical extent of the interface $H_{f}(T)$ in (b) and rescaled profile shapes in (c,d) for $N=2$, $\unicode[STIX]{x1D6EC}=2$ and $H_{e}=1/5$. In (a,b), the numerical solutions are shown as dots, while the early-time and late-time self-similar solutions are shown as straight lines. The insets in (b) are the profiles at different representative times $T=\{10^{-7},10^{0},10^{3}\}$ from numerical solutions. In (c,d), the numerical solutions depart from the capillarity similarity solution of (3.15) in the early-time period in (a), while they approach the confined similarity solution (compound wave) in the late-time period in (b).

Figure 18

Figure 17.Evolution of the front location $X_{f}(T)$ in (a), vertical extent of the interface $H_{f}(T)$ in (b) and profile shapes in (c,d) for $N=2$, $\unicode[STIX]{x1D6EC}=2$ and $H_{e}=1$. In (a,b), the numerical solutions are shown as dots, while the early-time and late-time self-similar solutions are shown as straight lines. The insets in (b) are the profiles at different representative times $T=\{10^{-8},10^{-1},10^{3}\}$ from numerical solutions. In (c,d), the numerical solutions depart from the capillarity similarity solution of (3.15) in the early-time period in (c), while they approach the confined similarity solution (modified shock) in the late-time period in (d).

Figure 19

Figure 18.Schematic regime diagram summarising the possible asymptotic behaviours during fluid injection into a confined porous layer. Six possible similarity solutions are identified: a capillarity solution (C) and buoyancy solution (B) for the early-time unconfined flows, and a shock solution (S), a modified shock solution (MS), a compound wave solution (CW) and a rarefaction solution (R) for the late-time confined flows. The early-time transition time $T_{t}$ is given by (3.25), while the late-time transition time $T_{t2}=T_{t2}(N,H_{e},\unicode[STIX]{x1D6EC})$.

Figure 20

Table 3.The influence of dimensionless parameters $N$, $H_{e}$ and $\unicode[STIX]{x1D6EC}$ on the similarity solutions for the interface shape $H(X,T)$ in the schematic regime diagram (figure 18). Here $N$ is the modified viscosity ratio, $H_{e}$ is the rescaled capillary length and $\unicode[STIX]{x1D6EC}$ is the pore heterogeneity parameter, as defined in table 1. The ‘universal shape’ in the late-time confined flow limit is defined as the universal functional form of $H/H_{i}$ versus $X/X_{f}$. Here ✓indicates that the parameter is relevant, while ✗ indicates that the parameter is irrelevant.

Figure 21

Table 4.Characteristic properties for the geological $\text{CO}_{2}$ sequestration projects at Sleipner and In Salah. The geophysical and two-phase flow data are taken from Bennion & Bachu (2005), Golding et al. (2011), Guo et al. (2016a), Yu et al. (2017) and Cowton et al. (2018). For the Sleipner project, the length of the horizontal well is taken from EPA (2010), while for the In Salah project, only the injection well KB-501 is considered with length 1 km (Petropoulos & Srivastava 2016). Here $S_{wi}$ is taken as the average value of four sandstone samples in Krevor et al. (2012). The capillary entry pressure is estimated as $p_{e}\approx \unicode[STIX]{x1D6FE}/k^{1/2}$, where $k$ is the permeability and $\unicode[STIX]{x1D6FE}\approx 30~\text{mN}~\text{m}^{-1}$ is the interfacial tension between supercritical $\text{CO}_{2}$ and brine (Bachu & Bennion 2009). The time and length scales ($t_{cs}$ and $x_{cs}$) in the sharp-interface model are defined in (2.11b,c), respectively, in Zheng et al. (2015a).

Figure 22

Figure 19.The distribution of supercritical $\text{CO}_{2}$ in the saline aquifer at the Sleipner site at $t=\{1,10,100\}$ yr: (a) shows simulation results based on the current model of partially saturating flows; the $\text{CO}_{2}$ front reaches $x_{f}\approx \{0.239,2.23,22.1\}~\text{km}$ and covers a total area of $A\approx \{1.99,19.5,194\}\times 10^{-3}~\text{km}^{2}$ at the corresponding times; (b) shows simulation results based on the sharp-interface model (Pegler et al.2014; Zheng et al.2015a); the $\text{CO}_{2}$ front arrives at $x_{f}\approx \{1.18,9.85,90.2\}~\text{km}$ and covers an area of $A\approx \{0.89,8.9,89\}\times 10^{-3}~\text{km}^{2}$ at identical times.

Figure 23

Figure 20.The distribution of supercritical $\text{CO}_{2}$ at the In Salah site at $t=\{1,10,100\}~\text{yr}$: (a) shows simulation results based on the current model of partially saturating flows; the $\text{CO}_{2}$ front reaches $x_{f}\approx \{1.85,18.5,185\}~\text{km}$ and covers an area of $A\approx \{21.4,211,2110\}\times 10^{-3}~\text{km}^{2}$ at the corresponding times; (b) shows simulation results based on the sharp-interface model (Pegler et al.2014; Zheng et al.2015a); the $\text{CO}_{2}$ front arrives at $x_{f}\approx \{0.716,6.86,68.4\}~\text{km}$ and covers a total area of $A\approx \{2.6,26,260\}\times 10^{-3}~\text{km}^{2}$ at identical times.

Figure 24

Table 5.Implications for geological $\text{CO}_{2}$ sequestration projects at the Sleipner and In Salah sites: predictions for the location of the spreading front ($x_{f}(t)$), the vertical extent of the interface $h_{f}(t)$ and total area covered by the $\text{CO}_{2}$ current ($A(t)$) from two different models. ‘SI’ represents the sharp-interface model (Pegler et al.2014; Zheng et al.2015a) and ‘UF’ represents the partially saturating flow model (current study).

Figure 25

Figure 21.Evolution for the front location $X_{f}(T)$ in (a) and vertical extent of the interface $H_{f}(T)$ in (b) for $N=1/2$, $\unicode[STIX]{x1D6EC}=2$ and $H_{e}=1/1000$. Numerical solutions are shown as dots, while the early-time and late-time self-similar solutions are shown as straight lines. The insets in (b) are the profiles at different representative times $T=\{10^{-14},10^{-4},10^{3}\}$ from numerical solutions.

Figure 26

Figure 22.Evolution of the rescaled shapes with $N=1/2$, $\unicode[STIX]{x1D6EC}=2$ and $H_{e}=1/1000$. The numerical simulation departs from the capillarity similarity solution of (3.15c) in the early-time period in (a), approaches the buoyancy similarity solution (3.22c) at intermediate times in (b), before eventually approaches the confined similarity solution in the late-time period in (c).

Figure 27

Figure 23.Evolution of the front location $X_{f}(T)$ in (a), vertical extent of the interface $H_{f}(T)$ in (b) and profile shapes in (c,d) for $N=1/2$, $\unicode[STIX]{x1D6EC}=2$ and $H_{e}=1/5$. In (a,b), the numerical solutions are shown as dots, while the early-time and late-time self-similar solutions are shown as straight lines. The insets in (b) are the profiles at different representative times $T=\{10^{-7},10^{-1},10^{3}\}$ from numerical solutions. In (c,d, the numerical solutions depart from the capillarity similarity solution of (3.15c) in the early-time period in (c), while they approach the confined similarity solution (modified shock) in the late-time period in (d)).