Hostname: page-component-7b7567c8c-7pwfn Total loading time: 0 Render date: 2026-11-16T21:16:28.864Z Has data issue: false hasContentIssue false

SPOD analysis of noise-generating Rossiter modes in a slat with and without a bulb seal

Published online by Cambridge University Press:  18 March 2021

Fernando H.T. Himeno*
Affiliation:
Department of Aeronautical Engineering, University of São Paulo, Av. Trabalhador São Carlense, 400, São Carlos, SP 13566-590, Brazil
Daniel S. Souza
Affiliation:
UNESP – São Paulo State University, Av. Profa. Isette Correa Fontão 505, São João da Boa Vista, São Paulo, 13876-750, Brazil
Filipe R. Amaral
Affiliation:
Department of Aeronautical Engineering, University of São Paulo, Av. Trabalhador São Carlense, 400, São Carlos, SP 13566-590, BrazilAeronautics Institute of Technology, Praça Marechal Eduardo Gomes 50, São José dos Campos, São Paulo, 12228-900, Brazil
Daniel Rodríguez
Affiliation:
ETSIAE-UPM (School of Aeronautics), Universidad Politécnica de Madrid, Plaza del Cardenal Cisneros 3, 28040 Madrid, Spain
Marcello A.F. Medeiros
Affiliation:
Department of Aeronautical Engineering, University of São Paulo, Av. Trabalhador São Carlense, 400, São Carlos, SP 13566-590, Brazil
*
†Email address for correspondence: fernando.himeno@usp.br

Abstract

The slat represents an important airframe noise source as it extends over almost the entire aircraft wingspan. Most studies of slat noise consider idealized geometries. However, for practical applications, several elements are installed on its cove, such as bulb seals to avoid direct contact with the main wing surface. Previous investigations of an unswept and untapered MD30P30N airfoil reported that the flow dynamics and the corresponding acoustic noise are very sensitive to the presence and location of the bulb seal. For certain locations a second recirculation bubble is created inside the slat cove and the acoustic narrowband peaks are intensified. The present paper shows that the two-bubble topology promotes the recirculation of turbulence within the slat cove. Spectral proper orthogonal decomposition analysis based on the radiated pressure intensity is used to identify the flow structures responsible for sound generation. Even though the recirculating turbulence is mostly incoherent, it interacts with the coherent Kelvin–Helmholtz vortices in the initial part of the mixing layer. Then, vortex merging and straining lead to the formation of complex vortex clusters. Our results show that the origin and evolution of these clusters are consistent with Rossiter's mechanism responsible for the narrowband peaks. The enhanced recirculation accelerates the cluster evolution leading to wider clusters and lower-frequency Rossiter modes.

Information

Type
JFM Papers
Copyright
© The Author(s), 2021. Published by Cambridge University Press
Figure 0

Figure 1.Scheme of slat flow. (a) Evolution of K–H vortices along the mixing layer and (b) scheme of the slat noise spectrum (PSD, power spectral density).

Figure 1

Figure 2.Scheme of cove flow observed for a bulb-sealed slat showing two recirculating regions.

Figure 2

Figure 3.The MD30P30N high-lift airfoil and slat geometry details.

Figure 3

Table 1.Geometrical parameters of MD30P30N as percentages of airfoil chord $c_{stowed}$.

Figure 4

Figure 4.Computational domain and refinement region details. (a) The seven refinement levels for the whole domain and (b) the refinement at the slat region with and without the bulb seal with a zoomed view closer to the seal edge showing the mesh points of this region.

Figure 5

Figure 5.(a) Root mean square of the dynamic pressure at a distance of $10 \times c_s$ from the origin for both cases and (b) line where the pressure is integrated for the far-field SPOD metric.

Figure 6

Figure 6.Streamlines and resolved TKE for the (a) baseline and (b) bulb-sealed cases, respectively one- and two-bubble reference topologies. Lines indicate the () mixing layer and the () return path separating the two bubbles. The white crosses indicate the position of maximum TKE.

Figure 7

Figure 7.Average spanwise vorticity for the cases of (a) one-bubble and (b) two-bubble topologies. Lines indicate the () mixing layer and the () return path between bubbles.

Figure 8

Figure 8.(a) Scheme showing segments of constant velocity-potential lines ($\eta$) along stages of the mixing-layer path ($s_{ML}$). Distribution of (b) TKE and (c) time-averaged spanwise vorticity over the $\eta$ segments.

Figure 9

Figure 9.Far-field noise spectra for one- and two-bubble topologies. Dotted lines represent the Rossiter mode frequencies ($St_n$) obtained using (4.1), with values summarized in table 2.

Figure 10

Figure 10.Typical snapshots of streamwise velocity fluctuations for (a) single-bubble and (b) two-bubble topologies.

Figure 11

Figure 11.The PSD of the streamwise velocity along the mixing-layer path for (a) single-bubble and (b) two-bubble topologies. Vertical dashed lines correspond to the Rossiter modes estimated using (4.1).

Figure 12

Table 2.Estimated Rossiter mode Strouhal numbers and frequencies based on (4.1) proposed by Souza et al. (2019).

Figure 13

Figure 12.The POD eigenvalues for (a) single-bubble and (b) two-bubble topologies.

Figure 14

Figure 13.Real part of the first SPOD mode for (a) one-bubble (baseline) and (b) two-bubble cases at selected frequencies. Dashed lines indicate the mixing layers of both cases and the return path of the two-bubble case.

Figure 15

Figure 14.Magnitude of the first SPOD mode for (a) one-bubble and (b) two-bubble cases. Dashed lines indicate the mixing layers of both cases and the return path of the two-bubble case.

Figure 16

Figure 15.Magnitude of modes $R_5$ and $R_2$ from cases of (a) one-bubble and (b) two-bubble topologies (see figure 14) indicating the () convective paths of the structures and their respective () acoustic paths. For reference, the mixing layers and return path are also shown as yellow continuous and dotted lines, respectively.

Figure 17

Figure 16.Convective velocity ($V_c$) along the convective paths indicated in figure 15.

Figure 18

Figure 17.Instantaneous spanwise vorticity inside the slat cove along 10 frames spaced by $1.42 \times 10^{-4}\ {\rm s}$ which covers a time period corresponding to Strouhal number $1.72$ ($782$ Hz) for (a) one-bubble and (b) two-bubble cases. Dashed lines indicate the mixing layers of both cases and the return path of the two-bubble case.

Figure 19

Figure 18.Instantaneous spanwise vorticity of frame 10 from the one-bubble case (figure 17) and mesh composed of the intersection points between the streamlines and equipotential lines, $\varPsi _i$ and $\varPhi _j$, shown both in their original coordinates and also in orthogonal axes.

Figure 20

Figure 19.Instantaneous spanwise vorticity for (a) one-bubble and (b) two-bubble slat cove flow cases along a time interval of $3.84 \times 10^{-3}$ s, which corresponds to a Strouhal number of $0.57$ ($260.6$ Hz). The contours are plotted along a mesh composed of transformed streamlines and equipotential lines (see figure 8a). Results shown in figure 17 correspond to frames 10 to 19 of this figure. The colourbar is the same as that of figures 17 and 18.