Hostname: page-component-7b7567c8c-7pwfn Total loading time: 0 Render date: 2026-11-16T08:53:51.416Z Has data issue: false hasContentIssue false

Jet and progeny formation in the Rayleigh breakup of a charged viscous drop

Published online by Cambridge University Press:  13 December 2019

Neha Gawande
Affiliation:
Department of Chemical Engineering, Indian Institute of Technology Bombay, Mumbai 400076, India
Y. S. Mayya
Affiliation:
Department of Chemical Engineering, Indian Institute of Technology Bombay, Mumbai 400076, India
Rochish Thaokar*
Affiliation:
Department of Chemical Engineering, Indian Institute of Technology Bombay, Mumbai 400076, India
*
†Email address for correspondence: rochish@che.iitb.ac.in

Abstract

Past experimental studies have indicated that the Rayleigh fission of a charged drop occurs via the formation of a jet followed by emission of progeny droplets. In order to understand this process, we model the evolution of a drop using an axisymmetric boundary element method in the viscous limit. In this work, the electrostatic model of a charged viscous liquid drop is modified by including surface charge dynamics. This model accounts for the finite charge relaxation time scales over which the drop surface is charged as well as the convection of charges by the interfacial flow. It is observed that, as the drop deforms with time, the generally applied assumption of an equipotential surface becomes invalid near the conical ends that experience singularly fast dynamics and the associated surface charge dynamics gives rise to tangential electric stresses. These tangential electric stresses exert an axial momentum on the fluid and are responsible for the formation of a jet and progeny droplets. Further, the progeny droplets are found to follow an inverse power-law scaling with the conductivity of the liquid and the smaller sized progenies carry a charge close to its Rayleigh limit.

Information

Type
JFM Papers
Copyright
© 2019 Cambridge University Press
Figure 0

Figure 1.Comparison of the temporal evolution of the drop shapes for the two cases of PC (dotted line) ($Sa=0$ and $\unicode[STIX]{x1D706}=30$) and FC (solid line) drop models (for $S=30$, $Sa=0.55$ and $\unicode[STIX]{x1D706}=30$). The inset at the right bottom corner is the experimental image of drop breakup presented by Duft et al. (2003) (reprinted with permission).

Figure 1

Figure 2.Comparison of the temporal evolution of curvature and charge density at the tip of the drop for the two cases of PC (filled symbols) and FC (open symbols) drop models (for $S=30$, $Sa=0.55$ and $\unicode[STIX]{x1D706}=30$).

Figure 2

Figure 3.Distribution of electric potential inside and outside the drop various times (a) $t=23$, (b) $t=23.5$ and (c) $t=23.8$ in the case of the finite conductor drop model.

Figure 3

Figure 4.The distribution of charge density ($q$) on the drop surface as a function of normalized arclength ($s$) at various times and drop shapes indicating point of maximum charge density (red dot) for the corresponding times in case of (a) PC and (b) FC drop models (for $S=30$, $Sa=0.55$ and $\unicode[STIX]{x1D706}=30$). The figures are magnified near the north pole for better clarity. Note that the abscissa is transformed using a relation $s^{\prime }=2(s-1)$, where $s$ is the normalized arclength of the drop and the data are shown for a half-drop due to perfect up–down symmetry across the equatorial plane.

Figure 4

Figure 5.Curvature of the drop as a function of normalized arclength for various times for (a) PC drop and (b) FC drop (for $S=30$, $Sa=0.55$ and $\unicode[STIX]{x1D706}=30$). The abscissa is transformed similar to figure 4.

Figure 5

Figure 6.Electric stress distribution (a,c) and velocity profiles (b,d) in the case of PC and FC drop model, respectively at time $t=23.8$. The electric stress is purely normal in the case of the PC drop model with maximum stress acting on the tip of the drop while the stress distribution is modified due to the presence of weak tangential stresses in the case of the FC drop model. The velocity profiles show the flow reversal due to modification of the stress distribution in the FC drop model (for $S=30$, $Sa=0.55$ and $\unicode[STIX]{x1D706}=30$).

Figure 6

Figure 7.Pressure distribution inside and outside the drop surface in the case of a finitely conducting liquid drop at (a) $t=23$, (b) $t=23.5$, (c) $t=23.8$ and (d) the blown tip of the drop at $t=23.8$ indicating the gradient formed inside the jet. A high pressure region is created below the flattened end which restricts the flow to the tip and forms a neck.

Figure 7

Figure 8.Effect of $Sa$ on the drop shapes formed before breakup in the FC drop case (for $S=30$ and $\unicode[STIX]{x1D706}=30$). (a) Size of the progeny, (b) length of the jet, (c) the ratio of charge carried by the progeny droplet to its Rayleigh limit and (d) deformed drop shapes as a function of $Sa$ at the onset of progeny detachment.

Figure 8

Figure 9.(a) Drop shapes at the onset of end pinch off for various values of viscosity ratio ($\unicode[STIX]{x1D706}$) (inset shows the blown up tips of the drop) and (b) scaling of progeny size and jet length with respect to viscosity ratio. Parameters used are $S=30$, $Sa=0.55$.

Figure 9

Figure 10.(a) Effect of nodes on the total surface charge without renormalization. The change in the total charge ($\unicode[STIX]{x1D6FF}Q$) with time is indicated as a percentage of the initial charge ($Q=8.1\unicode[STIX]{x03C0}$). (b) Effect of nodes on the shape of the drop near breakup to check the convergence of the results with mesh refinement. (Parameters used are $S=30$, $Sa=15$, $\unicode[STIX]{x1D706}=30$.)