Hostname: page-component-7b7567c8c-wxvwp Total loading time: 0 Render date: 2026-11-16T11:19:43.358Z Has data issue: false hasContentIssue false

A numerical investigation of acceleration-skewed oscillatory flows

Published online by Cambridge University Press:  04 November 2016

Pietro Scandura*
Affiliation:
Department of Civil Engineering and Architecture, University of Catania, Via Santa Sofia 64, 95123 Catania, Italy
Carla Faraci
Affiliation:
Department of Engineering, University of Messina, Contrada Di Dio (S. Agata), 98166 Messina, Italy
Enrico Foti
Affiliation:
Department of Civil Engineering and Architecture, University of Catania, Via Santa Sofia 64, 95123 Catania, Italy
*
†Email address for correspondence: pscandu@dica.unict.it

Abstract

Numerical simulations of wall-bounded acceleration-skewed oscillatory flows are here presented. The relevance of this type of boundary layer arises in connection with coastal hydrodynamics and sediment transport, as it is generated at the bottom of sea waves in shallow water. Because of the acceleration skewness, the bed shear stress during the onshore half-cycle is larger than in the offshore half-cycle. The asymmetry in the bed shear stress increases with increasing acceleration skewness, while an increase of the Reynolds number from the laminar regime causes the asymmetry first to decrease and then increase. Low- and high-speed streaks of fluid elongated in the streamwise direction emerge near the wall, shortly after the beginning of each half-cycle, at a phase that depends on the flow parameters. Such flow structures strengthen during the first part of the accelerating phase, without causing a significant deviation of the streamwise wall shear stress from the laminar values. Before the occurrence of the peak of the free stream velocity, the low-speed streaks break down into small turbulent structures causing a large increase in wall shear stress. The ratio of the root-mean-square (r.m.s.) of the fluctuations to the mean value (relative intensity) of the wall shear stress is approximately 0.4 throughout a relatively wide interval of the flow cycle that begins when breaking down of the streaks has occurred in the entire fluid domain. The acceleration skewness and the Reynolds number determine the phase at which this time interval begins. Both the skewness and the flatness coefficients of the streamwise wall shear stress are large when elongated streaks are present, while values of approximately 1.1 and 5.4 respectively occur just after breaking has occurred. The trend of both the relative intensity and the flatness of the spanwise wall shear stress are qualitatively similar to those of the wall shear in the streamwise direction. As a result of the acceleration skewness, the period-averaged Reynolds stress does not vanish. Consequently, an offshore directed steady streaming is generated which persists into the irrotational region.

Information

Type
Papers
Copyright
© 2016 Cambridge University Press 
Figure 0

Figure 1.Comparison between the wall shear stress measured in test 7 of Jensen et al. (1989) (markers) and that computed by means of the present numerical code (continuous line) for $\unicode[STIX]{x1D6FD}=0.5$ and $R_{\unicode[STIX]{x1D6FF}}=1120$ (a); comparison between the wall shear stress computed by means of (2.7) (continuous line) and the wall shear stress computed by means of the present numerical approach (markers) for $\unicode[STIX]{x1D6FD}=0.75$ and $R_{\unicode[STIX]{x1D6FF}}=500$ (b).

Figure 1

Figure 2.(a) Free stream velocity and acceleration for three different values of $\unicode[STIX]{x1D6FD}$. The maximum dimensionless velocity has been fixed to 1 in all the cases; thin lines: velocity; thick lines: acceleration; (b) time development of the streamwise velocity component $u$, in a position in the $y=0.42$ plane. For $R_{\unicode[STIX]{x1D6FF}}=1414$ the trends are offset by $-$1.

Figure 2

Figure 3.Time development of the ensemble-averaged wall shear stress during a cycle. (a) $R_{\unicode[STIX]{x1D6FF}}=1100$, (b) $R_{\unicode[STIX]{x1D6FF}}=1414$. Thin lines: laminar flow; thick lines: turbulent flow.

Figure 3

Table 1.Asymmetry parameters $A_{\unicode[STIX]{x1D70F}_{0}}$ and $\unicode[STIX]{x1D6E4}_{\unicode[STIX]{x1D70F}_{0}}$ of the bottom shear stress.

Figure 4

Figure 4.Asymmetry parameters $A_{\unicode[STIX]{x1D70F}_{0}}$ and $\unicode[STIX]{x1D6E4}_{\unicode[STIX]{x1D70F}_{0}}$ as functions of the Reynolds number (a); ensemble-averaged wall shear stress (b). $\unicode[STIX]{x1D6FD}=0.75$.

Figure 5

Figure 5.Ensemble-averaged velocity profiles at different phases during the period (a) $\unicode[STIX]{x1D6FD}=0.6$, (b) $\unicode[STIX]{x1D6FD}=0.75$, (c) $\unicode[STIX]{x1D6FD}=0.85$. Continuous line: $R_{\unicode[STIX]{x1D6FF}}=1100$; dashed line: $R_{\unicode[STIX]{x1D6FF}}=1414$.

Figure 6

Figure 6.Amplitudes $|\langle u\rangle _{1}|$, $|\langle u\rangle _{2}|$ and $|\langle u\rangle _{3}|$ (a,c,e) and phases $\unicode[STIX]{x1D719}_{1}$, $\unicode[STIX]{x1D719}_{2}$ and $\unicode[STIX]{x1D719}_{3}$ (b,d,f) of the first three harmonic components of the ensemble-averaged velocity profiles for $R_{\unicode[STIX]{x1D6FF}}=1100$.

Figure 7

Table 2.Distances from the wall $y_{max}$ and $y_{min}$ of the maximum and of the minimum velocity respectively during the cycle. According to the present scaling, in laminar flow $y_{max}$ and $y_{min}$ do not depend on the Reynolds number.

Figure 8

Figure 7.Ensemble-averaged velocity profiles in semi-log plot during the period for $R_{\unicode[STIX]{x1D6FF}}=1100$. Thin dashed line: $\langle u\rangle ^{+}=\log (y^{+})/0.41+5$.

Figure 9

Figure 8.Ensemble-averaged velocity profiles in semi-log plot during the period for $R_{\unicode[STIX]{x1D6FF}}=1414$. Thin dashed line: $\langle u\rangle ^{+}=\log (y^{+})/0.41+5$.

Figure 10

Figure 9.Low-speed streaks for $R_{\unicode[STIX]{x1D6FF}}=1100$ in the plane $y=0.16$. Darker areas denote the low-speed streaks. (a–d) $\unicode[STIX]{x1D6FD}=0.60$; (e–h) $\unicode[STIX]{x1D6FD}=0.75$; (i–l) $\unicode[STIX]{x1D6FD}=0.85$.

Figure 11

Figure 10.Evolution of the low-speed streaks and of the vortex structures during the first half-cycle for $R_{\unicode[STIX]{x1D6FF}}=1100$ and $\unicode[STIX]{x1D6FD}=0.75$. Darker regions denote the low-speed streaks; grey regions are the isosurfaces of second eigenvalue $\unicode[STIX]{x1D706}_{2}$ and denote the vortex cores; (a–e): $\unicode[STIX]{x1D706}_{2}=-0.007$, $u^{\prime }=-0.08$; (f) $\unicode[STIX]{x1D706}_{2}=-0.04$, $u^{\prime }=-0.16$; (a) $3\unicode[STIX]{x03C0}/64$, (b) $5\unicode[STIX]{x03C0}/64$, (c) $\unicode[STIX]{x03C0}/8$ (d) $3\unicode[STIX]{x03C0}/16$, (e) $13\unicode[STIX]{x03C0}/64$, (f) $\unicode[STIX]{x03C0}/4$.

Figure 12

Figure 11.(a) Low- and high-speed streaks in the range $12; darker areas denote low-speed streaks: see figure 9 for the contour map legend. (b) Trend of the velocity fluctuations along the spanwise direction at $x=12.5$ and $y=0.16$. $R_{\unicode[STIX]{x1D6FF}}=1100$, $\unicode[STIX]{x1D6FD}=0.75$, $t=\unicode[STIX]{x03C0}/8$.

Figure 13

Figure 12.Mean spacing between two low-speed streaks during the period. (a) $R_{\unicode[STIX]{x1D6FF}}=1100$; (b) $R_{\unicode[STIX]{x1D6FF}}=1414$.

Figure 14

Figure 13.Turbulent kinetic energy $k$ as a function of the time $t$ and of the $y$ coordinate. Contour interval: $10^{-3}$. (a,c,e) $R_{\unicode[STIX]{x1D6FF}}=1100$; (b,d,f) $R_{\unicode[STIX]{x1D6FF}}=1414$; (a,b) $\unicode[STIX]{x1D6FD}=0.60$; (c,d) $\unicode[STIX]{x1D6FD}=0.75$; (e,f) $\unicode[STIX]{x1D6FD}=0.85$.

Figure 15

Figure 14.Terms of the turbulent kinetic energy budget at 16 phases during the wave cycle for $\unicode[STIX]{x1D6FD}=0.75$ and $R_{\unicode[STIX]{x1D6FF}}=1100$.

Figure 16

Figure 15.(a,c) $R_{\unicode[STIX]{x1D6FF}}=1100$, (b,d) $R_{\unicode[STIX]{x1D6FF}}=1414$. (a,b) Production and dissipation of turbulent kinetic energy integrated along the $y$ direction. Here $I_{p}$ and $I_{\unicode[STIX]{x1D716}}$ denote the integral of production and dissipation respectively. (c,d) The lines denote $I_{p}+I_{\unicode[STIX]{x1D716}}$ while the markers denote the time derivative of the turbulent kinetic energy integrated along the $y$ direction $\unicode[STIX]{x2202}I_{k}/\unicode[STIX]{x2202}t$.

Figure 17

Figure 16.Energy spectra along the streamwise direction at six phases during the positive half-cycle for $R_{\unicode[STIX]{x1D6FF}}=1414$ and $\unicode[STIX]{x1D6FD}=0.75$. The straight lines are described by (3.4).

Figure 18

Figure 17.Reynolds stress $\langle u^{\prime }v^{\prime }\rangle$ as a function of the time $t$ and of the $y$ coordinate. Black lines: positive values, grey lines: negative values. Contour interval: $2\times 10^{-4}$. (a,c,e) $R_{\unicode[STIX]{x1D6FF}}=1100$; (b,d,f) $R_{\unicode[STIX]{x1D6FF}}=1414$; (a,b) $\unicode[STIX]{x1D6FD}=0.60$; (c,d) $\unicode[STIX]{x1D6FD}=0.75$; (e,f) $\unicode[STIX]{x1D6FD}=0.85$.

Figure 19

Figure 18.(a–c) Period average of the Reynolds stress $\overline{\langle u^{\prime }v^{\prime }\rangle }$; (d–f) period average of the ensemble-averaged streamwise velocity $\overline{\langle u\rangle }$.

Figure 20

Figure 19.Wall shear stress fluctuations for $R_{\unicode[STIX]{x1D6FF}}=1100$ and $\unicode[STIX]{x1D6FD}=0.75$. (a,e) $t=3\unicode[STIX]{x03C0}/16$; (b,f) $t=13\unicode[STIX]{x03C0}/64$; (c,g) $t=\unicode[STIX]{x03C0}/4$; (d,h) $t=9\unicode[STIX]{x03C0}/32$. Streamwise wall shear stress fluctuations $\unicode[STIX]{x1D70F}_{x}^{\prime }:$ (a) (min, max) $=$ ($-$0.0012, 0.0042); (b) ($-$0.0015, 0.0097); (c) ($-$0.0027, 0.0156); (d) ($-$0.0033, 0.0125). Spanwise wall shear stress $\unicode[STIX]{x1D70F}_{z}$: (e) (min, max) $=$ ($-$0.002, 0.0019); (f) ($-$0.0045, 0.0068); (g) ($-$0.0058, 0.0041); (h) ($-$0.0074, 0.0074). Black lines: positive values; grey lines: negative values. Contour interval: $5\times 10^{-4}$. The fluid oscillates along the $x$ direction.

Figure 21

Figure 20.Relative intensity $R_{x}=\unicode[STIX]{x1D70E}_{\unicode[STIX]{x1D70F}_{x}}/\unicode[STIX]{x1D70F}_{0}$ of the wall shear stress along the $x$ direction during the wave period. (a) $R_{\unicode[STIX]{x1D6FF}}=1100$, (b) $R_{\unicode[STIX]{x1D6FF}}=1414$.

Figure 22

Figure 21.Relative intensity $R_{z}=\unicode[STIX]{x1D70E}_{\unicode[STIX]{x1D70F}_{z}}/\unicode[STIX]{x1D70F}_{0}$ of the wall shear stress along the $z$ direction during the wave period. (a) $R_{\unicode[STIX]{x1D6FF}}=1100$, (b) $R_{\unicode[STIX]{x1D6FF}}=1414$.

Figure 23

Figure 22.Skewness coefficient $S_{x}$ of the wall shear stress along the $x$ direction during a wave period. (a) $R_{\unicode[STIX]{x1D6FF}}=1100$, (b) $R_{\unicode[STIX]{x1D6FF}}=1414$.

Figure 24

Figure 23.Flatness coefficient $F_{x}$ of the wall shear stress along the $x$ direction during a wave period. (a) $R_{\unicode[STIX]{x1D6FF}}=1100$, (b) $R_{\unicode[STIX]{x1D6FF}}=1414$.

Figure 25

Figure 24.Flatness coefficient $F_{z}$ of the wall shear stress along the $z$ direction during a wave period. (a) $R_{\unicode[STIX]{x1D6FF}}=1100$, (b) $R_{\unicode[STIX]{x1D6FF}}=1414$.

Figure 26

Figure 25.Probability density functions (p.d.f.) of the wall shear stress fluctuations along the $x$ direction, $\unicode[STIX]{x1D70F}_{x}^{\prime }/\unicode[STIX]{x1D70E}_{\unicode[STIX]{x1D70F}_{x}}$, at 16 phases during the cycle for $R_{\unicode[STIX]{x1D6FF}}=1100$ and $\unicode[STIX]{x1D6FD}=0.75$. Continuous lines show the numerical results while dashed lines show the log-normal probability density function that best fits to the numerical results.

Figure 27

Figure 26.Probability density functions (p.d.f.) of the wall shear stress $\unicode[STIX]{x1D70F}_{z}/\unicode[STIX]{x1D70E}_{\unicode[STIX]{x1D70F}_{z}}$ along the $z$ direction at 16 phases during the cycle for $R_{\unicode[STIX]{x1D6FF}}=1100$ and $\unicode[STIX]{x1D6FD}=0.75$. Continuous lines show the numerical results while dashed lines show the Pearson distribution type VII (3.9) that best fits to the numerical results. The curves denoted by dots at the phases $\unicode[STIX]{x03C0}/4$ and $3\unicode[STIX]{x03C0}/2$ are described by (3.10).

Figure 28

Figure 27.Trend of the functions $\unicode[STIX]{x1D713}_{1}$ and $\unicode[STIX]{x1D713}_{2}$ (see (3.11)–(3.13)) at 16 phases during the cycle for $R_{\unicode[STIX]{x1D6FF}}=1100$ and $\unicode[STIX]{x1D6FD}=0.75$; continuous lines: $\unicode[STIX]{x1D713}_{1}$; dashed lines: $\unicode[STIX]{x1D713}_{2}$.