Hostname: page-component-7b7567c8c-jvr6b Total loading time: 0 Render date: 2026-11-15T23:26:53.089Z Has data issue: false hasContentIssue false

Linear stability analysis and direct numerical simulation of two-layer channel flow

Published online by Cambridge University Press:  13 June 2016

Kirti Chandra Sahu
Affiliation:
Department of Chemical Engineering, Indian Institute of Technology Hyderabad, Sangareddy 502 285, Telangana, India
Rama Govindarajan*
Affiliation:
TIFR Centre for Interdisciplinary Sciences, Tata Institute of Fundamental Research, Narsingi, Hyderabad 500 075, India
*
†Email address for correspondence: rama@tifrh.res.in

Abstract

We study the stability of two-fluid flow through a plane channel at Reynolds numbers of 100–1000 in the linear and nonlinear regimes. The two fluids have the same density but different viscosities. The fluids, when miscible, are separated from each other by a mixed layer of small but finite thickness, across which the viscosity changes from that of one fluid to that of the other. When immiscible, the interface is sharp. Our study spans a range of Schmidt numbers, viscosity ratios and locations and thicknesses of the mixed layer. A region of instability distinct from that of the Tollmien–Schlichting mode is obtained at moderate Reynolds numbers. We show that the overlap of the layer of viscosity-stratification with the critical layer of the dominant disturbance provides a mechanism for this instability. At very low values of diffusivity, the miscible flow behaves exactly like the immiscible one in terms of stability characteristics. High levels of miscibility make the flow more stable. At intermediate levels of diffusivity however, in both linear and nonlinear regimes, miscible flow can be more unstable than the corresponding immiscible flow without surface tension. This difference is greater when the thickness of the mixed layer is decreased, since the thinner the layer of viscosity stratification, the more unstable the miscible flow. In direct numerical simulations, disturbance growth occurs at much earlier times in the miscible flow, and also the miscible flow breaks spanwise symmetry more readily to go into three-dimensionality. The following observations hold for both miscible and immiscible flows without surface tension. The stability of the flow is moderately sensitive to the location of the interface between the two fluids. The response is non-monotonic, with the least stable location of the layer being mid-way between the wall and the centreline. As expected, flow at higher Reynolds numbers is more unstable.

Information

Type
Papers
Copyright
© 2016 Cambridge University Press 
Figure 0

Figure 1.Schematic of the flows. (a) Miscible case: fluids ‘2’ and ‘1’ occupy the bottom ($0\leqslant y\leqslant h-q/2$) and top ($h+q/2\leqslant y\leqslant H$) layers, respectively. The two fluids are separated by a mixed layer of uniform thickness $q$. (b) The corresponding immiscible case.

Figure 1

Figure 2.Typical base steady-state profiles of (a) ${\it\mu}_{0}$ and (b) $U^{\prime \prime }$ for different values of $R_{s}$. The other parameters are chosen as $h=0.25$ and $q=0.1$.

Figure 2

Figure 3.Growth rates, ${\it\omega}_{i}$, of the most unstable disturbances as functions of the wavenumber, ${\it\alpha}$, for different values of the Reynolds number $\mathit{Re}$ for $\mathit{Sc}=10$, $q=0.02$, $R_{s}=1$ and $h=0.15$. The solid lines represent miscible flow, and the red dotted lines represent the result for immiscible two-fluid flow, with the interface placed at the same value of $h$, and with the same $R_{s}$. The symbols for a given Reynolds number are the same for miscible and immiscible flows.

Figure 3

Figure 4.The dispersion curves (${\it\omega}_{i}$ versus ${\it\alpha}$) for different values of (a) $\mathit{Sc}$ for $q=0.02$, and (b) $q$ for $\mathit{Sc}=10$. The rest of the parameter values are $\mathit{Re}=500$, $R_{s}=1$ and $h=0.15$. The dotted lines represent the results for the immiscible case.

Figure 4

Figure 5.Dispersion curves (${\it\omega}_{i}$ versus ${\it\alpha}$) for different values of (a) $h$ for $R_{s}=1$, (b) $R_{s}$ for $h=0.3$. The rest of the parameter values are $\mathit{Re}=500$, $\mathit{Sc}=100$ and $q=0.01$. The red dotted lines show the corresponding growth rates in the case of immiscible flow.

Figure 5

Figure 6.Neutral stability curves for different values of (a) $\mathit{Sc}$ for $h=0.8$, and (b) $h$ for $\mathit{Sc}=1000$. The rest of the parameter values are $R_{s}=0.6$ and $q=0.05$. For the boundaries which appear as closed curves, the region contained within is unstable, and the outside is stable. For the open curves, the region to the right is unstable, and that to the left is stable. The curves at high Reynolds number (of approximately 10 000, where ${\it\alpha}\sim 2$) correspond to the Tollmien–Schlichting mode of instability, whereas the other curves correspond to the overlap mode, as defined in Govindarajan (2004).

Figure 6

Figure 7.(a) Neutral stability curves, (b) $y_{cr}-h$ versus $\mathit{Re}$ along the lower limb of the neutral stability curves (shown in (a)). Without symbols: $\mathit{Sc}=0.01$, with symbols: $\mathit{Sc}=1$. The rest of the parameter values are $R_{s}=1$, $h=0.2$ and $q=0.05$. The regions contained within the red lines correspond to an order of magnitude estimate of the critical layer thickness $\pm (U_{cr}^{\prime }\mathit{Re}{\it\alpha})^{-1/3}/2$. Here $y_{cr}$ is the location of the critical layer, i.e. the $y$ at which $U=c_{r}$.

Figure 7

Figure 8.Variation of (a) kinetic energy $E$, (b) dissipation rate. The negative ($-D$) is shown to help viewing. (c) Production rate $P$ and (d) $P-D$ of the most dangerous disturbance mode (${\it\alpha}=4$) in the wall-normal direction for $\mathit{Re}=500$. The rest of the parameters are the same as those used to generate figure 3. The values of ${\mathcal{P}}$, ${\mathcal{D}}$ and $I$ normalised with ${\mathcal{E}}$ for the immiscible case are 0.8458, $-1.0745$ and 1.1326, respectively; ${\it\omega}_{i,max}=0.2159$. For the miscible case, the values of ${\mathcal{P}}$ and $\mathscr{D}$ normalised with ${\mathcal{E}}$ are 4.5379 and $-1.9227$, respectively; ${\it\omega}_{i,max}=0.3269$.

Figure 8

Figure 9.Comparison of the temporal evolution of the vertical perturbation obtained from linear stability analysis (solid lines) and direct numerical simulations (dashed lines). Miscible flow: symbols; immiscible flow: no symbols. The rest of the parameter values are $\mathit{Re}=500$, $\mathit{Sc}=100$, $R_{s}=2$, $h=0.3$ and $q=0.01$.

Figure 9

Figure 10.Temporal evolution of (a,c,d,g,h) $s=0.5$ contour for miscible flow with $q=0.05$, $\mathit{Sc}=100$; (b,e,f,i,j) interface for the immiscible case. (a,b) $t=4$, (c–f) 6 and (g–j) 10. The rest of the parameter values are $h=0.3$, $\mathit{Re}=500$ and $R_{s}=2$. The flow is along the positive $x$ direction. The side panels at $t=6$ are the cross-sectional views in the $x$–$z$ plane at $y=1$, and those at $t=10$ are the cross-sectional views in the $y$–$z$ plane at $x=3$.

Figure 10

Figure 11.Temporal evolution of (a,c,e,f,i) $s=0.5$ contour for miscible flow with $q=0.01$, $\mathit{Sc}=100$; (b,d,g,h,j) interface for the immiscible case. (a,b) $t=3$, (c,d) 5, (e–h) 7 and (i,j) 9. The rest of the parameter values are $h=0.4$, $\mathit{Re}=500$ and $R_{s}=2$. The flow is along the positive $x$ direction. The insets at $t=7$ represent cross-sectional views in the $x$–$z$ plane.

Figure 11

Figure 12.(a) $S_{0}$ profile, (b) the dispersion curve (${\it\omega}_{i}$ versus ${\it\alpha}$) obtained using the present base state and an error function profile. The other parameters are chosen as $\mathit{Re}=500$, $\mathit{Sc}=10$, $R_{s}=1$, $h=0.3$ and $q=0.1$.