Hostname: page-component-7b7567c8c-7pwfn Total loading time: 0 Render date: 2026-11-16T06:29:36.044Z Has data issue: false hasContentIssue false

Characteristic path analysis of confinement influence on steady two-dimensional detonation propagation

Published online by Cambridge University Press:  29 January 2019

Carlos Chiquete
Affiliation:
Los Alamos National Laboratory, Los Alamos, New Mexico, NM 87545, USA
Mark Short*
Affiliation:
Los Alamos National Laboratory, Los Alamos, New Mexico, NM 87545, USA
*
†Email address for correspondence: short1@lanl.gov

Abstract

Steady detonation in multi-dimensional flow is controlled by the chemical energy release that occurs in a subsonic elliptic flow region known as the detonation driving zone (DDZ). It is the region encompassing the detonation shock and sonic flow locus (in the frame of the detonation shock). A detonation that is strongly confined by material surrounding the explosive has the shock and sonic locus separated at the material interface. Information about the material boundary is traditionally believed to influence the DDZ structure via the subsonic flow on the boundary ahead of the sonic locus. A detonation that is weakly confined has the detonation shock and sonic locus intersecting at the material boundary. The sonic nature of the flow at the intersection point on the boundary is believed to isolate the DDZ structure from the material properties of the confinement. In this study, we examine the paths of characteristics propagating information about the confinement through the supersonic hyperbolic flow region that exists beyond the sonic locus, and determine whether these paths may impinge on the sonic locus and consequently influence the DDZ structure. Our configuration consists of a solid wall boundary deflected through a specified angle on detonation shock arrival, so that the streamline turning angle of the wall at the explosive edge is unambiguously defined. By varying the wall deflection angle from small through large values, we can systematically capture the evolution of the DDZ structure and the characteristic flow regions that influence its structure for strongly to weakly confined detonations. In all strong and weak confinement cases examined, we find that a subset of characteristics from the supersonic flow regions always impinge on the sonic locus. Limiting characteristics are identified that define the boundary between characteristics that impinge on the sonic surface and those that propagate information downstream of the sonic surface. In combination with an oblique-shock polar analysis, we show that the effects on the DDZ of characteristic impingement can be significant.

JFM classification

Information

Type
JFM Papers
Copyright
© 2019 Cambridge University Press 
Figure 0

Figure 1.Schematic of (a) strong and (b) weak confinement flow structures.

Figure 1

Figure 2.Schematic of $C^{+}$ characteristics for weak confinement originating from the expansion fan centred at the intersection of the detonation shock and sonic locus and impinging on the sonic locus. Based on a schematic shown in Bdzil (1981).

Figure 2

Figure 3.(a) Schematic of axial detonation propagation in either a 2D planar geometry ($\unicode[STIX]{x1D6FD}=T/2$) or axisymmetric 2D cylindrical geometry ($\unicode[STIX]{x1D6FD}=R$), in which a solid wall HE boundary is deflected through an angle $\unicode[STIX]{x1D703}$ upon detonation arrival. For computational purposes, the laboratory-frame $(r,z)$ geometry in (a) is mapped to the shock- and deflected wall-boundary-fitted frame $(\unicode[STIX]{x1D709},\unicode[STIX]{x1D702})$ shown in (b).

Figure 3

Figure 4.Shock polar analysis for (a) strong confinement and (b) weak confinement configurations.

Figure 4

Figure 5.Oblique wave polar solutions for the phase speeds $D_{0}$ indicated. The circles (SP) represent the post-shock sonic flow state. The PM fan solutions which originate out of the sonic flow state, and along which the flow is increasingly supersonic, are indicated by the dashed lines.

Figure 5

Figure 6.Variation of axial detonation phase speed $D_{0}$ with wall deflection angle $\unicode[STIX]{x1D703}$ for $T=20$. The green line represents the flow streamline angle $\unicode[STIX]{x1D703}_{s}$, independent of $D_{0}$, at which the flow behind the detonation shock is sonic, as determined from the shock polar analysis. Also shown is a multi-material calculation (MM) for $T=20$ confined by a weak low-density impedance confiner (LIC) material.

Figure 6

Figure 7.(a) Evolution of the DDZ with $\unicode[STIX]{x1D703},$ enclosed by the detonation shock (solid lines) and sonic locus (dashed lines), for $T=20$ and a range of $\unicode[STIX]{x1D703}$ from $\unicode[STIX]{x1D703}=17$ to $\unicode[STIX]{x1D703}=23.75$. Also shown is a multi-material calculation (MM) for $T=20$ for weak (LIC) confinement. (b) The transition region from strongly confining to weakly confining wall deflection angles. In (a) and (b), the DDZ structure for each $\unicode[STIX]{x1D703}$ has been offset such that the shock locus on $r=0$ is set to $z=0.$

Figure 7

Figure 8.The $C^{+}$ and $C^{-}$ characteristic paths in the supersonic flow region beyond the DDZ for $T=20$ and (a) $\unicode[STIX]{x1D703}=15.25,$ (b) $\unicode[STIX]{x1D703}=19.9,$ (c) $\unicode[STIX]{x1D703}=20.6$ and (d) $\unicode[STIX]{x1D703}=20.7.$ A selection of streamlines beyond the DDZ are also shown. The circles mark the end point of each characteristic path. The $C^{+}$ limiting characteristics shown terminate at the sonic point on the symmetry axis where $\text{d}z/\text{d}r=0$.

Figure 8

Figure 9.As for figure 8, but with (a) $\unicode[STIX]{x1D703}=21,$ (b) $\unicode[STIX]{x1D703}=21.75,$ (c) $\unicode[STIX]{x1D703}=23.75$ and (d) $\unicode[STIX]{x1D703}=25.75.$

Figure 9

Figure 10.(a) Comparison of the paths of three sets of $C^{+}$ characteristics that lie within the $C^{+}$ limiting characteristic and impinge on the sonic locus for $\unicode[STIX]{x1D703}=23.75$ and $\unicode[STIX]{x1D703}=25.75.$ The three end locations of the paths are designated points on the sonic locus. (b) The pressure along each characteristic path shown in (a).

Figure 10

Figure 11.Pressure variation along (a) the shock front and (b) the deflected wall for various $\unicode[STIX]{x1D703}$ for $T=20.$ The circles show the polar analysis predicted shock and wall pressure at the explosive edge for each angle.

Figure 11

Figure 12.Variation of axial detonation phase speed $D_{0}$ with wall deflection angle $\unicode[STIX]{x1D703}$ for $T=100$. The green line represents the flow streamline angle $\unicode[STIX]{x1D703}_{s}$, independent of $D_{0}$, at which the flow behind the detonation shock is sonic, as determined from the shock polar analysis. Also shown is a multi-material calculation (MM) for $T=100$ confined by a weak (LIC) material.

Figure 12

Figure 13.(a) Evolution of the DDZ with $\unicode[STIX]{x1D703},$ enclosed by the detonation shock (solid lines) and sonic locus (dashed lines), for $T=100$ and a range of $\unicode[STIX]{x1D703}$ from $\unicode[STIX]{x1D703}=10$ to $\unicode[STIX]{x1D703}=25.75$. Also shown is a multi-material calculation (MM) for $T=100$ for weak (LIC) confinement. The DDZ structure for each $\unicode[STIX]{x1D703}$ has been offset such that the shock locus on $r=0$ is set to $z=0.$ (b) A magnification of the DDZ structure near the deflected wall boundary.

Figure 13

Figure 14.The $C^{+}$ and $C^{-}$ characteristic paths in the supersonic flow region beyond the DDZ for $T=100$ and (a) $\unicode[STIX]{x1D703}=19.8,$ (b) $\unicode[STIX]{x1D703}=21$ and (c) $\unicode[STIX]{x1D703}=25.75.$ A selection of streamlines beyond the DDZ are also shown. The circles mark the end point of each characteristic path. The limiting $C^{+}$ characteristic is shown as the blue dashed line, while the limiting $C^{-}$ characteristic is shown as the red dashed line

Figure 14

Figure 15.As for figure 11, but with $T=100.$

Figure 15

Figure 16.Variation of axial detonation phase speed $D_{0}$ with wall deflection angle $\unicode[STIX]{x1D703}$ for $R=20$. The green line represents the fixed flow streamline angle $\unicode[STIX]{x1D703}_{s}$, independent of $D_{0}$, at which the flow behind the detonation shock is sonic, as determined from the shock polar analysis. Also shown is a multi-material calculation (MM) for $R=20$ confined by a weak (LIC) material.

Figure 16

Figure 17.(a) Evolution of the DDZ with $\unicode[STIX]{x1D703},$ enclosed by the detonation shock (solid lines) and sonic locus (dashed lines), for $R=20$ and a range of $\unicode[STIX]{x1D703}$ from $\unicode[STIX]{x1D703}=14.5$ to $\unicode[STIX]{x1D703}=22.5$. Also shown is a multi-material calculation (MM) for $R=20$ for weak (LIC) confinement. The DDZ structure for each $\unicode[STIX]{x1D703}$ has been offset such that the shock locus on $r=0$ is set to $z=0.$ (b) A magnification of the DDZ structure near the deflected wall boundary.

Figure 17

Figure 18.The $C^{+}$ and $C^{-}$ characteristic paths in the supersonic flow region beyond the DDZ for $R=20$ and (a) $\unicode[STIX]{x1D703}=14.5,$ (b) $\unicode[STIX]{x1D703}=19.8,$ (c) $\unicode[STIX]{x1D703}=21$ and (d) $\unicode[STIX]{x1D703}=22.5$. A selection of streamlines beyond the DDZ are also shown. The circles mark the end point of each characteristic path. The limiting $C^{+}$ characteristic is shown as the dashed blue line, while the limiting $C^{-}$ characteristic is shown as the dashed red line

Figure 18

Figure 19.As for figure 11, but with $R=20.$