Hostname: page-component-7b7567c8c-z4zkx Total loading time: 0 Render date: 2026-11-17T00:20:18.985Z Has data issue: false hasContentIssue false

Flow instabilities and impact of ramp–isolator junction on shock–boundary-layer interactions in a supersonic intake

Published online by Cambridge University Press:  09 December 2022

Nikhil Khobragade*
Affiliation:
Department of Mechanical Engineering, FAMU-FSU College of Engineering, Florida Center for Advanced Aero-Propulsion, FL 32310 USA
S. Unnikrishnan
Affiliation:
Department of Mechanical Engineering, FAMU-FSU College of Engineering, Florida Center for Advanced Aero-Propulsion, FL 32310 USA
Rajan Kumar
Affiliation:
Department of Mechanical Engineering, FAMU-FSU College of Engineering, Florida Center for Advanced Aero-Propulsion, FL 32310 USA
*
†Email address for correspondence: nk17b@fsu.edu

Abstract

Boundary layer instabilities and shock–boundary-layer interactions (SBLIs) critically affect the performance and safe operation of mixed-compression air intakes. We present a computational study anchored in companion experiments, to evaluate the multimodal mechanisms driving the dynamics of the external compression ramp flow and the cowl SBLI in a Mach $3$ intake. Boundary layer transition over the external ramp is first analysed through a global linear analysis, and the linear estimates are further validated through direct numerical simulations. The separation bubble over the ramp harbours three-dimensional stationary instabilities that induce transition, under the influence of secondary instabilities driven by the shear layer modes of the bubble. The interaction of the resulting turbulized boundary layer with the cowl shock at the ramp–isolator junction and its control through geometrical modification constitutes the second part of the study. We tested a faceted (baseline) and a notched (modified) junction design to evaluate its impact on the low-, mid- and high-frequency scales generated at the cowl SBLI region. In relation to the baseline case, the notched geometry effectively locks the separation point of the bubble, thus attenuating the upstream low-frequency breathing motion. The notch also energizes the midfrequency content through vortex shedding in a well-developed shear layer, which persists into the isolator, thus assisting in an efficient compression process through cross-stream mixing of near-wall flow. The isolator boundary layer in the notched design exhibits relatively lower static pressures and higher velocity fluctuations, which are conducive to improving the flow stability, unstart margin and efficiency of high-speed propulsion systems.

Information

Type
JFM Papers
Copyright
© The Author(s), 2022. Published by Cambridge University Press
Figure 0

Figure 1.(a) Schematic of a mixed-compression intake. (b) Details of the baseline (faceted) junction. (c) Details of the modified BFS (notched) junction. Here $A_{T}$ is the throat area.

Figure 1

Figure 2.Schematic of a mixed-compression intake model. Bottom wall pressure ports and total pressure rake are also indicated. The inset shows a cross-section of the rake measurement plane.

Figure 2

Figure 3.Ramp-only configurations of the (a) faceted and (c) notched junction designs. Cowl-side wall included in the (b) faceted and (d) notched junction designs. The junction geometries are magnified for clarity in the insets in (a,c). The vertical arrows in (b,d) mark the no-slip adiabatic wall simulated on the cowl-side.

Figure 3

Figure 4.Laminar flow field over the compression ramp utilized for stability analysis. Streamwise velocity contours are shown along with the dividing streamline that delineates the separation bubble.

Figure 4

Figure 5.Instability modes over the compression ramp. (a) Two-dimensional shear layer mode identified using contours of streamwise velocity. (b) Three-dimensional stationary mode identified using isolevels of streamwise velocity. The U0 surface in panel (b) is the spanwise-extruded surface corresponding to the dividing streamline shown in panel (a). Here (a) $St \sim 1.8$, ${\rm GR}\sim -0.1$; (b) $St = 0$, ${\rm GR}\sim 0.07$.

Figure 5

Figure 6.Flow structures in the compression ramp boundary layer identified using isolevel of Q-criterion, coloured with u-velocity. The inset shows a magnified flow field within the indicated regions of interest.

Figure 6

Figure 7.Streamwise velocity contours from the time-averaged DNS over the compression ramp. The evolution of velocity profiles along the ramp is also shown.

Figure 7

Figure 8.(a) Tangential velocity profile at the ramp-end at $x = 8.5$, plotted using wall units. Reference curves for the viscous sublayer and log-layer are also included. (b) One-dimensional energy spectra calculated from streamwise velocity fluctuations at $x = 8.5 \times {St}^{-5/3}$ and ${St}^{-7}$ lines are also indicated.

Figure 8

Figure 9.Wall-pressure spectra (log–PSD) of the compression ramp flow. Separation, reattachment, transition locations and KH mode frequency band are indicated.

Figure 9

Figure 10.The DMD modes extracted over the ramp from the DNS. (a,b) Pressure modes on the midspan plane. (c) Pressure mode on the wall-parallel surface. (d) The u-velocity mode on the wall-parallel surface. (e) Spanwise distribution of streamwise velocity of ‘$St \sim 0.036$’ dynamic mode decomposition (DMD) mode. (f) Wall-parallel slice of the stationary mode from linear analysis. The dashed lines indicate reattachment locations in panels (c,d). Dividing streamlines are indicated in the midspan contours. Here (a) $St \sim 1.75$ (p); (b) $St \sim 0.037$ (p); (c) $St \sim 1.81$ (p); (d) $St \sim 0.036$ (u); (e) $St \sim 0.036$ (u) at $x \sim 6.5$; (f) $St = 0.0$ (u-MFP).

Figure 10

Figure 11.Numerical shadowgraph of the full flow field with the cowl SBLI at the faceted junction.

Figure 11

Figure 12.Flow structures identified using isolevel of Q-criterion, coloured with u-velocity: (a) ROC and (b) cowl SBLI for the faceted geometry. Panels (c,d) are the corresponding results for the notched geometry. Impinging and reflected shocks in the interaction region are visualized using density gradient magnitude ($\| \boldsymbol {\nabla } \rho \|$) in (b,d).

Figure 12

Figure 13.The ${\boldsymbol {u}\boldsymbol {\cdot }\boldsymbol {\nabla } p}$ fields of all four cases: (a) ROC and (b) cowl SBLI for the faceted geometry. Panels (c,d) are the corresponding results for the notched geometry. Streamlines are also indicated, including the dividing streamlines for the SBLI cases. Important flow features are marked with numbers for SBLI cases.

Figure 13

Figure 14.Comparison of Experimental and DNS shadowgraphs of SBLI flow fields: (a,b) faceted junction and (c,d) notched junction.

Figure 14

Figure 15.Comparison of experimental and DNS wall pressures: (a) faceted junction and (b) notched junction. Corresponding Euler and RANS simulations are also included.

Figure 15

Figure 16.Wall pressure spectra (log–PSD) of the ramp, junction and isolator flow fields: (a) faceted ramp only; (b) faceted ramp SBLI; (c) notched ramp only; and (d) notched ramp SBLI. The red dashed lines indicate the transition to turbulence.

Figure 16

Figure 17.Wall pressure spectra (log–PSD) of junction SBLI: (a) Faceted and (b) Notched. Corresponding numerical shadowgraphs are also included for reference. The dotted line indicates the low-frequency peak in the faceted junction spectra. The dashed lines mark the reattachment locations. The dot-dashed lines mark the isolator start.

Figure 17

Figure 18.The r.m.s. pressures of the ramp–isolator junction flow fields: (a) faceted; (b) notched; (c) comparison along the domain centreline. The red line indicates probe points for comparison.

Figure 18

Figure 19.The r.m.s. pressures along the traces of (a) faceted and (b) notched junction. The ${\boldsymbol {u}\boldsymbol {\cdot }\boldsymbol {\nabla } p}$ fields aligned with the corresponding r.m.s. pressure distributions are also shown.

Figure 19

Figure 20.Contours of the low-frequency DMD modes in the (a–d) faceted and (e–h) notched junctions shown at equally spaced phase-intervals. The modes correspond to $St_L = 0.041$ and $St_L = 0.081$ for the faceted and notched cases, respectively. The mean flow field is added to the fluctuations. Here (a) $\phi =0$; (b) $\phi ={\rm \pi} /2$; (c) $\phi ={\rm \pi}$; (d) $\phi =3{\rm \pi} /2$; (e) $\phi =0$; (f) $\phi ={\rm \pi} /2$; (g) $\phi ={\rm \pi}$; (h) $\phi =3{\rm \pi} /2$.

Figure 20

Figure 21.Contours of the midfrequency DMD modes in the (a–d) faceted and (e–h) notched junctions shown at equally spaced phase-intervals. The modes correspond to $St_L = 0.526$ and $St_L = 0.395$ for the faceted and notched cases, respectively. The mean states of the corresponding cowl shocks and dividing streamlines are also indicated. Here (a) $\phi =0$; (b) $\phi ={\rm \pi} /2$; (c) $\phi ={\rm \pi}$; (d) $\phi =3{\rm \pi} /2$; (e) $\phi =0$; (f) $\phi ={\rm \pi} /2$, (g) $\phi ={\rm \pi}$; (h) $\phi =3{\rm \pi} /2$.

Figure 21

Figure 22.Contours of the high-frequency DMD modes in the (a–d) faceted and (e–h) notched junctions shown at equally spaced phase-intervals. The modes correspond to $St_L = 2.03$ and $St_L = 1.95$ for the faceted and notched cases, respectively. The mean states of the corresponding cowl shocks and dividing streamlines are also indicated. Here (a) $\phi =0$; (b) $\phi ={\rm \pi} /2$; (c) $\phi ={\rm \pi}$; (d) $\phi =3{\rm \pi} /2$; (e) $\phi =0$; (f) $\phi ={\rm \pi} /2$; (g) $\phi ={\rm \pi}$; (h) $\phi =3{\rm \pi} /2$.

Figure 22

Figure 23.Comparison of streamwise oscillations of (a) separation point and (b) reattachment point caused by various bands of frequencies in the faceted and notched junctions.

Figure 23

Figure 24.(a) The $\boldsymbol {u}\boldsymbol {\cdot }\boldsymbol {\nabla } P$ field with the probe points in the isolator. (b) Mean velocity profiles in inner scaling. (c) Static pressure profiles. (d) Stagnation pressure profiles. (e) Mach profiles.

Figure 24

Figure 25.(a) The r.m.s. velocity fluctuation intensities and (b) turbulent kinetic energy distribution across the isolator boundary layer.

Figure 25

Figure 26.The Y-velocity spectra (log–PSD) of isolator boundary layer: (a) faceted and (b) notched.

Figure 26

Figure 27.(a) Mach number and (b) total pressure recovery measured in the experiments at the end of the isolator.