Hostname: page-component-7b7567c8c-z4zkx Total loading time: 0 Render date: 2026-11-16T08:29:05.507Z Has data issue: false hasContentIssue false

Transient wave-induced pore-water-pressure and soil responses in a shallow unsaturated poroelastic seabed

Published online by Cambridge University Press:  18 March 2022

Linlong Tong
Affiliation:
Key Laboratory of Ministry of Education for Coastal Disaster and Protection, Hohai University, Nanjing 210098, PR ChinaDepartment of Civil and Environmental Engineering, National University of Singapore, 117576, Republic of SingaporeCollege of Harbor, Coastal and Offshore Engineering, Hohai University, Nanjing 210098, PR China
Philip L.-F. Liu*
Affiliation:
Department of Civil and Environmental Engineering, National University of Singapore, 117576, Republic of SingaporeInstitute of Hydrological and Oceanic Sciences, National Central University, Jhongli, Taoyuan 320, Taiwan, ROCSchool of Civil and Environmental Engineering, Cornell University, Ithaca, NY 14850, USADepartment of Hydraulic and Ocean Engineering, National Cheng Kung University, Tainan, 10701 Taiwan, ROC
*
†Email address for correspondence: philip.liu@nus.edu.sg

Abstract

An analytical solution is developed for studying transient water wave-induced responses inside an unsaturated poroelastic seabed of finite thickness. The soil skeleton and the pore fluid are compressible and the constitutive relationship of the soil skeleton is described by Hooke's law. Assuming that the horizontal length scale of wave motion is much larger than the seabed thickness, the leading-order analytical solutions for the seabed responses, including pore fluid pressure and soil skeleton motion, are obtained. The present solutions are suitable for general transient wave loading and for the shear modulus of the soil skeleton being of the same order of magnitude as the effective bulk modulus of elasticity of the pore fluid. The present theory is first validated by checking the solutions with the experimental data for the pore pressure induced by periodic-wave loading. The present analytical solutions are then used to investigate the seabed responses under transient waves, including linear periodic wave, a solitary wave and a bore. The effects of the wave-induced effective stresses on the bed failure potential are further analysed. The results show that the shear failure potential and its duration are highly dependent on the soil properties, such as saturation degree, shear modulus and permeability. Sensitivity analyses are presented.

Information

Type
JFM Papers
Copyright
© The Author(s), 2022. Published by Cambridge University Press
Figure 0

Figure 1.Sketch of a transient wave propagating over a seabed of finite thickness.

Figure 1

Table 1.Summary of physical conditions in the water–soil column experiments and wave–seabed interaction experiments.

Figure 2

Figure 2.Vertical profiles of the maximum wave-induced pore pressure in case I of Liu & Jeng (2013) and case II of Liu et al. (2015). Circles, experimental results; solid lines, the present solution at leading order; and dashed lines, the previous solution without considering the deformation of the soil skeleton (Liu et al.2007). Physical parameters are given in table 1.

Figure 3

Figure 3.Experimental set-up and instrument layout in Anderson et al. (2017): (a) beach profile and sand pit; (b) illustration of the instrument configuration (including the acoustic Doppler velocimeters (ADVs), the conductivity concentration profilers (CCPs) and the pore-pressure transducer array (PPTA)), looking towards the beach; (c) the spanwise view of the PPTA and CCP in the sandy bed; and (d) the onshore view of sensor proximities.

Figure 4

Figure 4.Time histories of (a) free-surface elevation at the offshore edge of the sandbar, (b) wave-induced pore-pressure gradient in the horizontal direction at 0.9 cm below the water–seabed interface, and (c) wave-induced pore-pressure gradient in the vertical direction. Grey dots, phase-averaged experimental results; error bars, standard deviation; black line, the present solutions with the physical parameters listed in table 1.

Figure 5

Figure 5.Time histories of wave-induced pressure gradients at 0.9 cm below the water–seabed interface: (a) the horizontal gradient and (b) the vertical gradient. Green line, $G=1\times 10^4$ Pa; blue line, $G=1\times 10^5$ Pa; red line, $G=1\times 10^6$ Pa; and black line, $G=1\times 10^7$ Pa. The other parameters used for calculation are listed in table 1.

Figure 6

Figure 6.Time histories of wave-induced pressure gradients at 0.9 cm below the water–seabed interface: (a) the horizontal gradient and (b) the vertical gradient. Black line, $S_r=0.99$; red line, $S_r=0.98$; and blue line, $S_r=0.97$. The other parameters used for calculation are listed in table 1.

Figure 7

Figure 7.Time histories of the linear periodic-wave-induced dimensionless pore pressure within an unsaturated poroelastic seabed at three different elevations: (a) $Z=1$ on the seabed–water interface, (b) $Z=0.5$ at mid-depth of the seabed, and (c) $Z=0$ on the seabed bottom. Black solid lines, the present solution (3.12); and red dashed lines, the solution of Liu et al. (2007) for rigid soil skeleton. The following parameters are used for calculation: $n=0.45$, $\nu =0.33$, $G=K=2\times {10^7}$ Pa, $k_s=1\times {10}^{-10}~\textrm {m}^2$, $\rho _f=1\times 10^3~\textrm {kg}~\textrm {m}^{-3}$, $v_f=1\times {10}^{-6}~\textrm {m}^2~\textrm {s}^{-1}$, $d^\prime =10~\textrm {m}$, $h^\prime =30~\textrm {m}$, $T^\prime =15~\textrm {s}$ and ${a^\prime _0}/{h^\prime }=0.1$.

Figure 8

Figure 8.Contours of pore pressure and effective stresses inside a seabed: (a) the time history of the linear wave-induced dynamic water pressure at the water–seabed interface; (b) contours of the pore pressure $p$; (c) contours of the horizontal effective stress $\tau _{xx}$; (d) contours of the vertical effective stress $\tau _{zz}$; and (e) contours of the shear stress $\tau _{xz}$. The physical parameters used in the calculation are given in the caption of figure 7.

Figure 9

Figure 9.Time histories of linear wave-induced dimensionless velocity components at three different elevations, (a,b) $Z=1$, (c,d) $Z=0.5$ and (e, f) $Z=0$, within an unsaturated poroelastic seabed. Black solid lines, the pore fluid velocity components; blue solid lines, the soil skeleton velocity components;red solid lines, the velocity difference of the pore fluid and soil skeleton calculated by the present solutions; and red dashed lines, the velocity difference of the pore fluid and soil skeleton calculated by Liu et al. (2007) for a rigid soil skeleton. The physical parameters used in the calculation are given in the caption of figure 7.

Figure 10

Figure 10.Vertical profiles of the dimensionless velocity components of the pore fluid, the soil skeleton and the seepage flow at four different phases: (a) the time history of the dynamic water pressure at the water–seabed interface; (b–e) the vertical profiles of the horizontal velocity components at $\varphi _1=-0.75$, $\varphi _2=-0.50$, $\varphi _3=-0.25$ and $\varphi _4=0$, respectively; and ( f–i) the vertical profiles of the vertical velocity components at $\varphi _1=-0.75$, $\varphi _2=-0.50$, $\varphi _3=-0.25$ and $\varphi _4=0$, respectively. Black solid lines, the pore fluid velocity components; blue solid lines, the soil skeleton velocity components; red solid lines, the differences of the pore fluid and soil skeleton velocities calculated by the present solutions; and red dashed lines, the difference of the pore fluid and soil skeleton velocities calculated by Liu et al. (2007). The physical parameters used in the calculation are given in the caption of figure 7.

Figure 11

Figure 11.Time histories of the solitary-wave-induced dimensionless pore pressure within an unsaturated poroelastic seabed at three different elevations: (a) $Z=1$ on the seabed–water interface; (b) $Z=0.5$ at mid-depth of the seabed; and (c) $Z=0$ on the seabed bottom. Black solid lines, the present solution (3.12); and red dashed lines, the solution of Liu et al. (2007) for a rigid soil skeleton. The following parameters are used for calculation: $\alpha =2.79$, $\beta =0.36$, $\kappa _1=3.33\kappa _2$ and $\tilde {\nu }=0.25$. These correspond to the physical conditions: $n=0.45$, $\nu =0.33$, $G=K=2\times {10^7}$ Pa, $k_s=1\times {10}^{-10}~\textrm {m}^2$, $\rho _f=1\times 10^3~\textrm {kg}~\textrm {m}^{-3}$, $v_f=1\times {10}^{-6}~\textrm {m}^2~\textrm {s}^{-1}$, $d^\prime =10~\textrm {m}$, $h^\prime =30$ m and ${a^\prime _0}/{h^\prime }=0.2$.

Figure 12

Figure 12.Contours of pore pressure and effective stresses inside a seabed: (a) the time history of the solitary-wave-induced dynamic water pressure at the water–seabed interface; (b) contours of the pore pressure $p$; (c) contours of the horizontal effective stress $\tau _{xx}$; (d) contours of the vertical effective stress $\tau _{zz}$; and (e) contours of the shear stress $\tau _{xz}$. The physical parameters used in the calculation are given in the caption of figure 11.

Figure 13

Figure 13.Time histories of solitary-wave-induced dimensionless velocity components at three different elevations, (a,b) $Z=1$, (c,d) $Z=0.5$ and (e, f) $Z=0$, within an unsaturated poroelastic seabed. Black solid lines, the pore fluid velocity components; blue solid lines, the soil skeleton velocity components; red solid lines, the velocity difference of the pore fluid and soil skeleton calculated by the present solutions; and red dashed lines, the velocity difference of the pore fluid and soil skeleton calculated by Liu et al. (2007) for a rigid soil skeleton. The physical parameters used in the calculation are given in the caption of figure 11.

Figure 14

Figure 14.Vertical profiles of the dimensionless velocity components of the pore fluid, the soil skeleton and the seepage flow at five different phases: (a) the time history of the dynamic water pressure at the water–seabed interface; (b–f) the vertical profiles of the horizontal velocity components at $\varphi _1=-2$, $\varphi _2=-1$, $\varphi _3=0$, $\varphi _4=1$ and $\varphi _5=2$, respectively; and (g–k) the vertical profiles of the vertical velocity components at $\varphi _1=-2$, $\varphi _2=-1$, $\varphi _3=0$, $\varphi _4=1$ and $\varphi _5=2$, respectively. Black solid lines, the pore fluid velocity components; blue solid lines, the soil skeleton velocity components; red solid lines, the differences of the pore fluid and soil skeleton velocities calculated by the present solutions; and red dashed lines, the difference of the pore fluid and soil skeleton velocities calculated by Liu et al. (2007). The physical parameters used in the calculation are given in the caption of figure 11.

Figure 15

Figure 15.Time histories of the bore-induced dimensionless pore pressure at three different elevations inside the seabed: (a) $Z=1$, (b) $Z=0.5$ and (c) $Z=0$.Black solid lines, the present solution; and red dashed lines, the solution of Liu et al. (2007). The physical parameters used in the calculation are given in the caption of figure 11.

Figure 16

Figure 16.Contours of the pore pressure and effective stresses under a bore: (a) the time history of the dynamic water pressure at the water–seabed interface; (b) contours of the pore pressure $p$; (c) contours of the horizontal effective stress $\tau _{xx}$; (d) contours of the vertical effective stress $\tau _{zz}$; and (e) contours of the shear stress $\tau _{xz}$. The physical parameters used in the calculation are given in the caption of figure 11.

Figure 17

Figure 17.Time histories of the bore-induced dimensionless velocity components for the pore fluid and soil skeleton at three different elevations: (a,b) $Z=1$, (c,d) $Z=0.5$ and (e, f) $Z=0$. Black solid lines, the pore fluid velocity components; blue solid lines, the soil skeleton velocity components; red solid lines, the relative velocity between pore fluid and soil skeleton calculated by the present solutions; and red dashed lines, the relative velocity between pore fluid and soil skeleton calculated by Liu et al. (2007). The physical parameters used in the calculation are given in the caption of figure 11.

Figure 18

Figure 18.Vertical profiles of the dimensionless velocity components of the pore fluid and the soil skeleton in the seabed at five different phases: (a) the time history of the dynamic water pressure at the water–seabed interface; (b–f) the vertical profiles of the horizontal velocity components at $\varphi _1=-2$, $\varphi _2=-1$, $\varphi _3=0$, $\varphi _4=1$ and $\varphi _5=2$, respectively; and (g–k) the vertical profiles of the vertical velocity components at $\varphi _1=-2$, $\varphi _2=-1$, $\varphi _3=0$, $\varphi _4=1$ and $\varphi _5=2$, respectively. Black solid lines, the pore fluid velocity components; blue solid lines, the soil skeleton velocity components; red solid lines, the relative velocity between pore fluid and soil skeleton calculated by the present solutions; and red dashed lines, the relative velocity between pore fluid and soil skeleton calculated by Liu et al. (2007). The physical parameters used in the calculation are given in the caption of figure 11.

Figure 19

Figure 19.(a) Time history of the phase-averaged dynamic water pressure at the water–seabed interface measured by Anderson et al. (2017). (b) The contour map of the stress angle inside the seabed. The stress angle achieves its maximum, $29.8^\circ$, at the seabed bottom when $t=0.525$. The physical parameters are given in table 1.

Figure 20

Figure 20.(a) The time history of the dynamic water pressure at the water–seabed interface under a linear wave with $T^\prime =15~\textrm {s}$, $h^\prime =30$ m and $a_0^\prime /h^\prime =0.10$. (b) The colour map of the stress angle inside the seabed during linear wave propagation. The stress angle achieves the maximum, $31.6^\circ$, at the water–seabed interface in the deceleration phase, and the red line indicates the contour of $\phi =\phi _c$. The physical parameters used in the calculation are given in the caption of figure 7.

Figure 21

Figure 21.(a) The time history of the dynamic water pressure at the water–seabed interface under a solitary wave with $a_0^\prime /h^\prime =0.2$ and $h^\prime =30$ m. (b) The colour map of the stress angle inside the seabed under a solitary wave. The stress angle achieves the maximum, $20.7^\circ$, at the water–seabed interface when $\varphi =-0.94$. The physical parameters used in the calculation are given in the caption of figure 11.

Figure 22

Figure 22.(a) The time history of the dynamic water pressure at the water–seabed interface under a solitary wave with $a^\prime _0/h^\prime =0.4$ and $h^\prime =30~\textrm {m}$. (b) The colour map of the stress angle inside the seabed. The red line indicates the contour of $\phi =\phi _c$, and the black line indicates the contour of $\phi =90^\circ$. The other parameters used in the calculation are consistent with those given in the caption of figure 11.

Figure 23

Figure 23.(a) History of the dynamic water pressure at the water–seabed interface under a bore. $(b)$ Contours of the stress angle inside the seabed under a bore. The stress angle reaches the maximum $19.98^\circ$ at the bottom of the seabed when $\varphi =0.04$. The physical parameters used in the calculation are given in the caption of figure 11.

Figure 24

Figure 24.The contour map of the maximum stress angle $\phi _{{max}}(S_r,Z)$ induced by a solitary wave with $a_0^\prime /h^\prime =0.4$ and $h^\prime =30$ m (the red line indicates the contour of $\phi _{{max}}(S_{r},Z)=\phi _c$). Shear failure occurs when $S_r\leq {0.9943}$. The physical parameters used in the calculation are given in the caption of figure 11.

Figure 25

Figure 25.(a) The time history of the dynamic water pressure at the water–seabed interface under a solitary wave with $a^\prime _0/h^\prime =0.4$ and $h^\prime =30$ m. (b) The interface between the shear failure zone and the stable zone under the conditions of $S_r=0.96$, 0.98, 0.99 and 0.993. The parameters used in the calculation are given in the caption of figure 11.

Figure 26

Figure 26.The contour map of the maximum stress angle, $\phi _{{max}}(\tilde {G},Z)$, induced by a solitary wave with $a^\prime _0/h^\prime =0.4$ and $h^\prime =30$ m. The red line indicates the contour of $\phi _{{max}}(\tilde {G},Z)=\phi _c$, and shear failure occurs when $\tilde {G} \geq 0.068$. In the calculation, the shear modulus varies between $2\times {10^6}$ Pa and $4.4\times {10^8}$ Pa, and the other physical parameters used in the calculation are given in the caption of figure 11.

Figure 27

Figure 27.(a) The time history of the dynamic water pressure at the water–seabed interface under a solitary wave with $a^\prime _0/h^\prime =0.4$ and $h^\prime =30$ m (b) The interface between the shear failure zone and the stable zone under the conditions of $\tilde {G}=0.1$, 0.3, 1.0 and 10. The other parameters used in the calculation are given in the caption of figure 11.

Figure 28

Figure 28.The contour map of the maximum stress angle, $\phi _{{max}}(\kappa _2^2,Z)$, induced by a solitary wave with $a_0^\prime /h^\prime =0.4$ and $h^\prime =30$ m; the red line indicates the contour of $\phi _{\textrm {max}}(\kappa _2^2,Z)=\phi _c$. In the calculation, the soil permeability varies from $10^{-11}~\textrm {m}^2$ to $10^{-9}~\textrm {m}^2$, and the other physical parameters used in the calculation are given in the caption of figure 11.

Figure 29

Figure 29.(a) The time history of the dynamic water pressure at the water–seabed interface under a solitary wave with $a^\prime _0/h^\prime =0.4$ and $h^\prime =30$ m. (b) The interface between the shear failure zone and the stable zone under soil permeability conditions of $\kappa _2^2=2\times {10^{-3}}$, $7\times {10^{-3}}$ and $2\times {10^{-2}}$. The parameters used in the calculation are given in the caption of figure 11.