Introduction

More than 50 years ago, Markov and Zheleznykh proposed using gigatons of transparent material underground as a detector of cosmic neutrinos (see Markov and Zheleznykh, 1986, and references therein). The IceCube Neutrino Observatory completed in December 2010 (IceCube Collaboration, 2006) and its predecessor, AMANDA (Antarctic Muon and Neutrino Detector Array; AMANDA Collaboration, 2001), have applied this concept in the deep ice at the South Pole to study fundamental questions in physics and astrophysics. These telescopes use large volumes of ice to observe the subatomic charged particles produced by energetic neutrinos, that have fortuitously interacted via the weak force with nucleons in the ice near the detector. Muons, hadronic cascades and electromagnetic cascades generated by the neutrinos can be tracked via charged-particle Cherenkov radiation at ultraviolet and visible wavelengths with an embedded matrix of sensitive photo-multipliers. The density of sensors and size of the instrumented volume determine the threshold, resolution and practicably attainable upper limit of detected neutrino energies. Since the spectrum of cosmic neutrinos is presumed to roughly follow that of cosmic rays and fall steeply with energy, IceCube was designed at the kilometer scale to detect small fluxes of neutrinos in the 1 TeV to 1 PeV energy range over the lifetime of the experiment.

The buried component of IceCube consists of 5160 photomultiplier tubes, frozen into 86 boreholes and arrayed over 1 km³ from 1450 m to 2450 m depth (IceCube Collaboration, 2009). IceCube and AMANDA rely on the extreme clarity of Antarctic ice, at sufficient depths that all residual air bubbles originally trapped in surface snow have converted to hydrates. Air clathrate hydrate crystals have almost exactly the same refractive index as ice (Δn/n ≈ 4 × 10⁻³; Reference Uchida, Shimada, Hondoh, Mae and BarkovUchida and others, 1995) and so are essentially transparent. The first detector, AMANDA-A deployed in 1994, was installed at depths between 800 and 1000 m in the expectation that all bubbles had converted at those depths. Barkov and Lipenkov had carried out a painstaking analysis of fresh Vostok ice-core samples, crucially, within a few weeks of coring and before the hydrates could revert back to air bubbles upon relaxation at the surface. Their work (Barkov and Lipenkov, 1985) presaged our discovery that South Pole ice is still bubbly at depths shallower than 1300 m. Bubble scattering prevented accurate directional reconstruction, and AMANDA-A was mainly effective as a subatomic particle calorimeter (Reference AskebjerAskebjer and others, 1995) but not as a telescope. Bubbles decrease in size with depth but persist until at least ∼1350 m at South Pole, and to comparable or greater depths at every location we have studied in the interiors of Antarctica and Greenland.

IceCube construction depended critically on the drilling team and the 5 MW Enhanced Hot-Water Drill (EHWD), capable of boring 20 holes, each 2500 m deep and 60 cm in diameter, in a 2 month season. This massive ice-drilling project has enabled us to investigate South Pole ice and create synergies with other disciplines. Our studies to date include precision measurements of optical properties (Reference Woschnagg and PriceWoschnagg and Price, 2001; Reference AckermannAckermann and others, 2006; IceCube Collaboration, 2013); acoustic properties (IceCube Collaboration, 2010, 2011); glaciological properties such as flow, shear and temperature (Reference PricePrice and others, 2002); and paleoclimatology, including a reconstruction of surface roughness as a proxy for cyclonic activity (Reference Bay, Rohde, Price and BramallBay and others, 2010).

A principal aspect of calibrating the IceCube detector has been to map scattering and absorption of light in the deep ice. Bubble-free Antarctic ice is the purest natural solid on Earth, and the most transparent at ultraviolet to visible wavelengths. Photons with wavelengths shorter than ∼200 nm are strongly attenuated by electronic absorption in water; for wavelengths longer than ∼600 nm, molecular absorption dominates. Between 200 and 600 nm, transmission in ice is limited by trace impurities (Reference He and PriceHe and Price, 1998). To model the response of the detector, we must account for impurity variations in three dimensions, particularly due to climatic and glaciological changes in continental mineral dust and volcanic ash inclusions with depth (Reference AckermannAckermann and others, 2006; IceCube Collaboration, 2013). The concentration and character of deposited particulates in the ice vary due to glacial flow and past climate changes, with higher concentrations corresponding to periods of greater abundance of dust available from source regions, and possibly longer-range transport due to changes in atmospheric circulation or precipitation (Reference Legrand and MayewskiLegrand and Mayewski, 1997; Reference Li, Ramaswamy, Ginoux, Broccoli, Delworth and ZengLi and others, 2010). The mineral dust found in Antarctic ice is thought to originate primarily in Patagonia, with uncertain and possibly variable contributions from Australia, New Zealand and Africa (Reference DelmonteDelmonte and others, 2008; Reference Li, Ginoux and RamaswamyLi and others, 2008; Reference GabrielliGabrielli and others, 2010). The ice in which IceCube is instrumented accumulated during the last glacial period, with climate changes manifest as variations in optical clarity of nearly an order of magnitude. Bulk absorption length ranges from 30 to >200 m, in ice from colder versus warmer periods respectively. Effective scattering length varies between about 5 and 70 m. Volcanic ash layers, particularly those deposited by local circum-Antarctic volcanoes, can severely degrade optical transparency on the centimeter scale.

AMANDA and IceCube used various light sources embedded in the ice with the detector to make optical measurements at ∼10 m resolution (Ackermann and others, 2007; IceCube Collaboration, 2013). In addition, we deployed laser dust loggers (Reference Bramall, Bay, Woschnagg, Rohde and PriceBramall and others, 2005) in eight IceCube boreholes. The logger can often produce a more stratigraphically coherent environmental record than can be obtained from ice-core measurements, which must make do with mere ∼0.001 m² sections of the horizon. In holes drilled mechanically using non-freezing fluid to retrieve a core, optical logging data can be degraded by scarring of the borehole wall (Reference Bramall, Bay, Woschnagg, Rohde and PriceBramall and others, 2005; Reference Fudge and SmithFudge and Smith, 2010), fluid contamination and refractive mismatch with the ice. The IceCube hot water holes, however, provided almost ideal conditions for imaging dust and volcanic particulate horizons at millimeter depth resolution (Reference Bramall, Bay, Woschnagg, Rohde and PriceBramall and others, 2005).

Here we develop a detailed South Pole climate record by correlating our measurements to the EDC99 ice core taken at Dome C, East Antarctica, by the EPICA Collaboration (European Project for Ice Coring in Antarctica; Reference ParreninParrenin and others, 2007a; Reference Lambert, Bigler, Steffensen, Hutterli and FischerLambert and others, 2012) together with the laser borehole log we made there in January 2010. The South Pole record is unbroken to 100 ka bp at the IceCube location. Extrapolation indicates that South Pole ice should include the Eemian period, the last interglacial ∼120 ka bp with a climate analogous to but several degrees warmer than the present day (Reference Sime, Wolff, Oliver and TindallSime and others, 2009). Although the South Pole is one of the most studied locations in Antarctica, no ice core deeper than a few hundred meters has ever been retrieved from the site. Partly based on the AMANDA and IceCube datasets, including results shown here, South Pole has been designated as the site of the next major US ice-coring mission.

Methods

Optical and photonic logging instruments deployed in glacial boreholes can provide a wealth of information, without retrieval or destruction of core samples. The dust logger (Reference Bay, Price, Clow and GowBay and others, 2001) grew out of years of AMANDA experience in using emitters and receivers embedded in ice to measure optical properties. The ∼1 m-long logger (Fig. 1) shines light into the ice surrounding a borehole; photons scatter off bubbles and impurities to be eventually absorbed; a small fraction (10⁻¹⁰ to 10⁻⁶) of photons return to be detected. Annular black nylon brush baffles sweep ice crystals and debris from the source beam and intercept stray light, to ensure that all detected photons have exited and reentered the borehole after interacting with the target layer.

Fig. 1.

Ruggedized laser dust logger deployed in IceCube. The 404 nm diode laser is focused into a fan beam to probe 60° of the horizon in one pass. Brush baffles block photons which circumvented the ice through the borehole, and clear away detritus in the hole that could obstruct the image. IceCube hot-water boreholes were larger and less uniform than depicted in the diagram.

The intrinsic depth resolution of the logger is determined by the thickness of the laser line and not the distance of the receiver from the source, which we have confirmed using Monte Carlo simulations (Reference Bay, Price, Clow and GowBay and others, 2001) and other logger geometries we have tested (Reference BayBay and others, 2006). The signal is dominated by first encounters of the laser with particulates in the coherence plane of the beam, which probes approximately one effective scattering length into the ice. The further the source beam penetrates horizontally the greater the coherence with the target dust layer, up to the scale of stratigraphic undulations or tilt. At depths where scattering is bubble-dominated, the ice is diffusively illuminated by scattered light and the logger signal tracks impurity levels through absorption, responding markedly to thin volcanic ash layers. In deep clear ice, the back-scattering signal is a nearly direct tracer of ash and continental mineral dust.

In 2004 we designed and built a new dust logger for use during IceCube commissioning (Reference Bramall, Bay, Woschnagg, Rohde and PriceBramall and others, 2005). We improved upon previous designs by using a temperature-regulated diode laser at 404 nm wavelength near the absorption minimum for glacial ice (Reference AskebjerAskebjer and others, 1997a), a photon-counting detector (Hamamatsu HC135), onboard computer control (Rabbit RCM3720) and DSL (digital subscriber line, Patton Electronics Co., Gaithersburg, MD, USA) telemetry to the surface.

While more ideal optics could scan an entire 360° with adjustable azimuthal integration, we compromised on a ruggedized design that could survive many rapid redeployments by restricting the focus of the laser plane to span a fixed 60° of the horizon. The pressure vessel was constructed from hardened stainless steel and synthetic sapphire optical components. The brush baffles extended to 18 in (∼46 cm) in diameter, not enough to completely seal the annulus of the holes, which typically varied from 45 to 75 cm diameter. Raw photon counts were corrected for pileup at high light levels and normalized to the intensity of the laser. Depth was reconstructed to an absolute accuracy of 1–2 m from Bourdon tube pressure sensors (Paroscientific, Redmond, WA, USA). The reconstruction incorporated winch payout, surface surveys, well depth measured with a laser rangefinder, and corrections for water column compressibility and cable stretch.

The first two loggers were permanently attached to the bottoms of detector strings and took data as the strings were deployed. Beginning with the 2006/07 season, we used a small winch to deploy and recover the instrument at a nominal logging speed of ∼25 cm s⁻¹. Each borehole was logged in one ∼6 hour round trip, immediately after drilling, to leave time for installation of the detector string in the refreezing hole.

In January 2010, we deployed the laser dust logger at the EPICA Dome C ice-core (EDC99) site in East Antarctica (75°06′ S, 123°21′ E), to obtain the particulate history which dates to 800 ka there (Reference JouzelJouzel and others, 2007). The laser data from the EDC99 borehole were somewhat obscured by turbidity from drill fluid contaminants, but were effective for finding many additional candidate ash layers beyond those previously investigated in the core (Reference Narcisi, Petit, Delmonte, Basile-Doelsch and MaggiNarcisi and others, 2005).

Reference Bigler, Röthlisberger, Lambert, Stocker and WagenbachBigler and others (2006) performed continuous flow analysis (CFA) on melted EDC99 core samples, including laser-absorption particle sensing of total insoluble dust, fluorescence spectroscopy of Ca²⁺ and absorption spectroscopy of Na²⁺. Reference Lambert, Bigler, Steffensen, Hutterli and FischerLambert and others (2012) derived a record of Dome C calcium ions excluding those due to Ca-rich sea salt, i.e. non-sea-salt calcium (nssCa²⁺), which is a proxy for continental silicate mineral dust.

Laser borehole logging and core measurements complement other methods for measuring atmospheric particulate variations as preserved in ice. The logging signal is a relative measure of scattering and absorption due to impurities and bubbles. The logger captures high-definition images of the optical effects of particulates averaged over an area of order m² of the horizon. This method is often less susceptible than a core sample to the depositional noise, redistribution and erosion that degrade continuity of the preserved climate record. The logger signal amplitude can be affected by hole light leakage and a varying distance to the target dust, particularly in the large boreholes of IceCube, and exhibits some smoothing from pre-imaging and post-imaging spillover at depths near strong optical features. Ice-core CFA systems make measurements with millimeter spatial resolution, which is well below the scale of homogeneity of the cores. Core samples comprise only a few cm² area of the horizon, and measurements need to be averaged over a finite depth interval to meaningfully represent the strati-graphic record. Core records may miss thin deposition events and contain gaps, depth registration errors, inter-sample mixing and particle loss intrinsic to CFA.

By identifying common features precisely, we can synchronize our laser profiles and combine them into a full-resolution average South Pole particulate history. Similarly, though generally at lower resolution, we are able to map common distinct features between histories that were measured with different techniques or at different locations. To match records, we used both manual visual inspection and an automated feature alignment algorithm. The laser logger recorded a measurement every 2–3 mm, and our South Pole stratigraphic record includes meaningful, repeatable structure at the sub-centimeter depth scale. The analysis of millions of measurements with minimal information loss required the use of a fully automated synchronization scheme. We developed a procedure based on dynamic time warping and internal consistency error suppression (Reference Bay, Rohde, Price and BramallBay and others, 2010).

The matching engine optimized for our South Pole laser dust logs did not perform as well when used to align sequences from different measurement techniques or sites. To match South Pole logger and EDC99 ice-core data with the algorithm, we smoothed the core data with a mild spline and used our Dome C optical log to corroborate feature matches at the centimeter scale. We verified and corrected a select subset of automated matching results by visual inspection for determining the primary age scale. Over some intervals, particularly in bubbly ice, only manual matching was effective. To aid visual inspection we used the MatchMaker MATLAB ice-core analysis utility (Reference RasmussenRasmussen, 2006). At the South Pole, termination of the Last Glacial Maximum (LGM) into the Holocene epoch coincides with the bubble–hydrate transition at about 800–1150 m where the optical signal amplitude changes by orders of magnitude. Definitive feature identification was challenging over this interval, and we required additional evidence below for stratigraphic control.

Results

Logger profiles made in IceCube boreholes 21, 50, 66, 52, 10, 2, 86 and 14 between 2004 and 2011 (Fig. 2a) include some of the best-resolved records of Antarctic particulate stratigraphy available from the last glacial period. Figure 2b shows the locations of the eight holes across IceCube. These laser profiles served as reference points to model layer undulations throughout the array, with isochrons depicted as topographic gradients in Figure 3a, and as layer contours in Figure 3b–f. At interstitial positions within the convex hull (smallest envelope) defined by logged holes, layering can be interpolated with standard gridding methods (natural neighbor, kriging). For stability and to extrapolate locations outside the hull, we used a modified ridge estimator in the MATLAB shareware program gridfit (Reference D’ErricoD’Errico, 2005). Extrapolations outside reference data should of course be treated with caution. Since the first hole 21 log only reached 2113 m due to an instrument failure, the deepest ∼350 m in the southeast corner of the array must also be extrapolated. Inside the hull, the ridge estimator and natural-neighbor tessellation methods typically agreed within the 1–2 m absolute depth accuracy.

Fig. 2.

(a) Borehole laser logging resolved sub-centimeter particulate features in repeated measurements. The early stages of the LGM are toward the left edge of the plot. The log of hole 21 stopped near ∼2100 m due to an instrument failure. (b) IceCube surface map and logged boreholes marked with solid color-coded circles. The y-axis points to Greenwich, UK, and as of 2011 the origin of the IceCube coordinate system was 509 m north and 982 m west of the South Pole (11 06 m along 63°W).

Fig. 3.

Aerial view of dust layer tilt across IceCube at five depths, which shows the influence of basal topography likely increasing toward bedrock. (a) Arrows depict downhill direction and relative tilt magnitude of modeled isochrons. Layering outside convex hulls (polygons) defined by reference logging data is extrapolated and poorly constrained. Surface ice flow velocity is 10.1 m a⁻¹ along 320° based on IceCube survey data. (b–f) Modeled dust isochrons at each depth, with contours indicating every 2 m change in elevation and lower levels shaded darker. Absolute depth accuracy of reference logs is 1–2 m and modeled layers do not necessarily intersect every control point.

Figure 4 compares our borehole laser measurements with a record made from the Dome C ice core using a state-of-the-art CFA system. A linear scaling of logger photon counts gives good agreement with EDC99 nssCa²⁺. The roughly linear instrumental response is shown in Figure 5, which compares IceCube laser logging profiles to EDC99 and EPICA Dronning Maud Land (EDML) (Reference FischerFischer and others, 2007) core dust. For the EDML comparison, we synchronized to core dust at only ∼1 m resolution.

Fig. 4.

Comparison between borehole laser records at South Pole (upper traces) and non-sea-salt calcium from continuous flow chemistry in Dome C EDC99 (lower traces; Reference Lambert, Bigler, Steffensen, Hutterli and FischerLambert and others, 2012) over a 70 ka interval on the EDC3 timescale. The light gray curve is the laser profile for hole 86 only; the violet curve is a composite average of all profiles. EDC99 non-sea-salt calcium measurements are plotted before (black) and after spline smoothing (blue). Marine isotope stage 4 and select Antarctic isotope maxima are labeled for context.

Fig. 5.

The response of the logger in clear ice is approximately proportional to dust content. Signal amplitude for IceCube logging runs compared with synchronized core nssCa²⁺ from EDC99 (a) and EPICA Dronning Maud Land (b; 75°S, 0.067° E; Reference FischerFischer and others, 2007). Normalized logger signal counts have been raised to the power 3/2 to relate scattering cross section (particle dimension squared) to mass (particle dimension cubed).

The most prominent dust feature at IceCube instrumented depths is marine isotope stage 4 (MIS4), a large peak between about 1950 and 2100 m, corresponding to about 60–70 ka, which strongly affects detector response to particle physics events. Like the LGM at ∼25 ka, this cold interval and concomitant peak in dust are believed to result principally from a 41 ka period minimum in the obliquity of the ecliptic (Reference BergerBerger, 1978) according to Milankovitch theories (Reference Hays, Imbrie and ShackletonHays and others, 1976; Reference Huybers and WunschHuybers and Wunsch, 2005) as well as extraterrestrial accretion theories (Reference Muller and MacDonaldMuller and MacDonald, 1997) of orbitally controlled climate.

The EHWD provided a smooth transparent window through which we could make precision scans of in situ particulates, from clean water-filled boreholes with refractive index matching the ice (Δn/n ≈ 1.5% at 404 nm; Reference GrayGray, 1972; Reference Price and WoschnaggPrice and Woschnagg, 2001). Scattering by residual air bubbles in the ice reduced the contrast of particulate scattering and made unambiguous identification of horizons increasingly difficult in layers shallower than the LGM around ∼1100 to 1250 m. Between 1200 and 1350 m, we suppressed the contribution from bubble scattering with an ad hoc amplitude correction of 0.37% per meter of depth, which forced the logger signal profile to conform to the core dust profiles.

We have refined our South Pole age scale (AMANDA Collaboration, 1995; Reference Price, Woschnagg and ChirkinPrice and others, 2000) for 90% of the ice depth and at multiple points traversing an area of order one ice-sheet thickness in lateral extent (Figs 6–8). We used common features to link South Pole and Dome C and adopted the EDC3 timescale of Reference ParreninParrenin and others (2007a). At shallow and intermediate depths in bubbly ice, ash and dust features matched layers detected in our Dome C dust log. We have also referred to early AMANDA measurements of absorption which indicated the falling edge of the LGM dust peak near ∼900 m, with an absorption length comparable to the cleanest IceCube depths (Reference AskebjerAskebjer and others, 1997b). In the deep clear ice, we tied our laser profiles to nssCa²⁺ measurements in the Dome C ice core (Reference Lambert, Bigler, Steffensen, Hutterli and FischerLambert and others, 2012). We manually verified a subset of algorithmic matches for the hole 86 log near the array center, to use for primary age. Figure 7 shows a comparison between manual and automated age curves. The primary age curve also includes a control point from aerial radar extrapolated from Titan Dome, located ∼100 km south-southeast of South Pole, taken to be 165 ka at 2850 m (Reference Siegert and HodgkinsSiegert and Hodgkins, 2000). After applying a simple two-parameter quadratic (forced through the origin) transformation of Dome C depth

EDC3 age tracks our South Pole curve. Figure 7 compares the new age-versus-depth scale with earlier AMANDA versions which were based on limited control data.

Fig. 6.

(a) South Pole age versus depth, constructed by aligning laser profiles with corresponding ash and dust features at Dome C, on the EDC3 timescale. The red curve is a two-parameter quadratic depth transformation of Dome C age, which closely matches that of South Pole. An increase in accumulation rate is evident in the Dome C analog during the Eemian period, which is likely also represented at South Pole. A bedrock control point extrapolated from Titan Dome is taken to be 165 ka at 2850 m (Reference Siegert and HodgkinsSiegert and Hodgkins, 2000). (b) Borehole laser dust logger signal, overlaid with spline-smoothed Dome C nssCa²⁺ manually synchronized with South Pole. Above ∼1000 m depth the logger signal is dominated by scattering from bubbles and absorption by volcanic ash.

Fig. 7.

(a) South Pole age versus depth presented here (solid), compared with previous versions (dotted, dashed) from AMANDA (AMANDA Collaboration, 1995; Reference Price, Woschnagg and ChirkinPrice and others, 2000). (b) Primary South Pole age for hole 86 determined by manual inspection (black) compared with a spline-smoothed curve using the algorithm (red), and age discrepancy between the two methods (blue). The automated matching engine consistently mismatches the leading edge of MIS4 near ∼70 ka.

Fig. 8.

(a) Internal variation of IceCube feature elevations across the kilometer array, relative to the central hole 86, used as control points for layer modeling in Figure 3. (b) South Pole age curves from automated synchronization of each log with EDC99 nssCa²⁺.

Decades of work with shallow South Pole cores have shown that the depths of recent historical volcanic events can vary by several meters within just a few lateral kilometers. Reference HamiltonHamilton (2004) attributed this to topographically controlled micro-local accumulation variability. Ice-Cube was surveyed every season, and depths are referenced to a fixed elevation, which is the floor of the drilling tower for the first hole, No. 21. Figure 8a shows elevation variability of common features over the full depth range. Isochron tilting exceeds 70 m across the kilometer of IceCube for deeper features, probably as bedrock topography increasingly protrudes into the ice layering. Figure 8b shows age–depth relationships from automated synchronization of the eight laser logs with EDC99 nssCa²⁺.

Figure 9 shows annual-layer thicknesses derived from the age–depth relationships in Figure 8. Variations in accumulation rate generally track climate changes, and the variations in our layer thicknesses are roughly consistent with dating-constrained flow models of the Dome C and Dome Fuji cores (Reference ParreninParrenin and others, 2007b).

Fig. 9.

(a) South Pole annual-layer thickness derived from the eight age curves in Figure 8, spline-smoothed (gray) and 300 year average (black). Variations track layer thicknesses from East Antarctic flow models of Dome C (b) and Dome Fuji (c) (Reference ParreninParrenin and others, 2007b).

For age control in the Holocene, we used the volcanic ash horizons detailed in Table 1, in which the ascribed eruptions deposited detectable ash at both sites. Ash layers are the most prominent optical features available for this period and are apparent in the raw signal in Figure 6b. Most layers could be detected easily in every laser profile we made. The two near ∼800 m were clear after comparison with Dome C data using MatchMaker, and roughly agree with two echoes seen with surface radar (Besson and Kravchenko, 2013). Although discrete opaque layers that were isolated optically could also be the fallout from extraterrestrial sources or intense dust storms, for the purposes of reconstructing chronologies the strata need only be unambiguously matched between sites. Four of the layers were abundant enough in ice cores to have been micro-chemically investigated and traced to extra-Antarctic volcanoes of the South Sandwich Islands (Reference Narcisi, Petit, Delmonte, Basile-Doelsch and MaggiNarcisi and others, 2005) and South America (Reference Narcisi, Petit, Delmonte, Basile-Doelsch and MaggiNarcisi and others, 2005; Reference KurbatovKurbatov and others, 2006). These ashfalls appear to have been widespread over much of the continent including West Antarctica (Reference BayBay and others, 2006), as well as the Southern Ocean (Reference Nielsen, Hodell, Kamenov, Guilderson and PerfitNielsen and others, 2007), making them valuable horizons for dating.

Table 1.

Opaque thin layers, presumed to be volcanic ash, used for age control in the shallow bubbly portion of the ice sheet. Four of the layers have been examined in the EDC99 core and were consistent with volcanoes of the South Sandwich Islands (SSI), Southern Andes (SA) and Marie Byrd Land (MBL) (Reference Narcisi, Petit, Delmonte, Basile-Doelsch and MaggiNarcisi and others, 2005). The layer near ∼710 m dates the same as a layer in the Siple Dome core deemed to originate from a South American (sA) eruption (Reference KurbatovKurbatov and others, 2006). The South Pole layers near ∼800 m and ∼810 m were not clearly identifiable in all logs and were matched as part of this study

Many eruptions, particularly the more powerful silicic variety, may be badly estimated (Reference Toohey, Kruger and TimmreckToohey and others, 2013) or missed using core acidic volatiles and detectable only via tephra layers (Reference CoulterCoulter and others, 2012). The Toba super-eruption in Sumatra, Indonesia, occurred ∼74 ka bp and is one of the most powerful eruptions known, possibly the largest volcanic event of the last 2 Ma (Reference Rose and ChesnerRose and Chesner, 1990). Toba has been implicated as the trigger for a volcanic winter and millennial-scale cold phase, and even a human population bottleneck detected in genomic studies (Reference Rampino and SelfRampino and Self, 1992; Reference AmbroseAmbrose, 1998). Yet Toba has never been conclusively identified in any Antarctic or Greenland ice core (Reference SvenssonSvensson and others, 2013). Recently, Reference Storey, Roberts and SaidinStorey and others (2012) used an astronomically calibrated ⁴⁰Ar/³⁹Ar Toba age to place the eruption between Antarctic isotope maxima 19 and 20. We plot this period in our optical logging data in Figure 10, which does include several upward spikes in signal likely indicating the presence of thin layers of volcanic ash. Heavier ashfalls tend to be the products of relatively nearby eruptions of modest intensity, which partly explains why Toba has so far eluded investigators.

Fig. 10.

South Pole laser logs over the interval now known to bracket Toba, the enigmatic supereruption which has never been found in an ice core. The five traces have been aligned to hole 86 depths using the automated matching algorithm. Thin spikes like that near 2146 m are most likely ash deposits, though heavier ashfalls tend to be products of nearby circum-Antarctic volcanoes.

Discussion

In addition to mineral grains and volcanic ash, natural ice impurities include salts, acids and soot (Reference He and PriceHe and Price, 1998). The particulate absorption and scattering that are sensed with optical methods are the result of varying particle number densities, sizes, shapes and albedos. Although impurity deposition over the continent is remarkably uniform, the particulate records at different Antarctic sites are not perfect analogs of each other but depend on location, elevation, accumulation and atmospheric circulation patterns. The composition, scattering efficiency and absorption efficiency of impurities likely also vary in time with climate (e.g. because of a changing contribution of dust from Australia relative to South America (Reference Lambert, Bigler, Steffensen, Hutterli and FischerLambert and others, 2011)). Some of the nonlinearity in Figure 5 could reflect a lower average dust albedo at high concentrations, or local variations. In extremely pure ice, backscattered light is a good tracer of mineral dust content, though the linearity can be expected to eventually break down at high enough number densities.

Although the intrinsic resolution of the logger is ∼2–3 mm, the fixed 60° fan spanned by the laser line source produces an average over depositional noise (surface roughness) embedded in the stratigraphic record. The logger could be made more effective with laser imaging techniques like those employed in scanning lidar systems. By sweeping the beam through 360° of the horizon and preserving azimuthal information, future designs could help disentangle and extract surface roughness information for an improved dust record.

Snow accumulation at South Pole is unusually high, considering its elevation and mean annual temperature, because of frequent inland penetration by low-pressure systems from the Weddell Sea as well as the Pacific sector. Apart from accumulation rate, the glaciology of South Pole has much in common with the Vostok (East Antarctica) ice-core site. Both locations are relatively cold, flat ‘flank’ sites far from an ice divide or dome. Horizontal flow at both sites is substantial (3 m a⁻¹ at Vostok and 10 m a⁻¹ at South Pole) and may involve converging ice streams. Intervals of the Vostok core show a strong girdle fabric (Reference Lipenkov, Barkov, Duval and PimientaLipenkov and others, 1989; Reference Obbard and BakerObbard and Baker, 2007) in which the ice is subjected to pure shear and crystal c-axes fall in a vertical plane perpendicular to the direction of flow. Studies of aerial radar have suggested a disrupted South Pole stratigraphy (Reference Bingham, Siegert, Young and BlankenshipBingham and others, 2007) and the possibility that tributaries of nearby ice streams have migrated through an area where flow velocities have varied over time (personal communication from D. Blankenship, 2011). Knowledge of the South Pole area is incomplete, based on limited radar and satellite surface velocity measurements south of 87°S. New aerogeophysical surveys would allow us to fit our maps into the larger context, and comparison with our stratigraphy could provide new insights for understanding englacial radar attenuation and interpreting radargrams.

Conclusions

IceCube logged eight hot-water boreholes using a high-resolution laser dust logger, permitting detailed glaciological reconstructions without local core samples. Optical back-scattering in clear ice matches EDC99 ice-core non-sea-salt calcium, over a last glacial climate record which is intact back to at least 100 ka at South Pole. We see no stratigraphic folding to 87% depth to bedrock across IceCube, although we found undulations of internal layering of order ∼10% (0.1 km elevation change over 1 km) in the cross-flow direction, which are consistent with radargrams. South Pole annual-layer history is consistent with accumulation variability in East Antarctic ice cores. Several volcanic ash layers match across the continent and we examined the interval around Toba for candidate tephra deposits.

Together with hot-water or mechanical fast access drilling, optical logging can be used to determine age, stratigraphic integrity and scientific potential of a site before devoting the resources of a coring mission. A detailed particulate depth profile can be used to immediately date any site on the continent precisely and confidently. A primary goal of the International Partnerships in Ice Core Sciences is to obtain a core reaching back >1.5 Ma, in ice likely to be found in the deep East Antarctic ice sheet (Reference JonesJones, 2007). Such a project will require a substantial reconnaissance effort to determine optimal sites for drilling before a deep-coring drill is fielded. Aerial radar is not always reliable for absolute age determination, especially in the deepest parts of an ice sheet where radar echo layers can be missing or difficult to interpret (Reference DrewsDrews and others, 2009). An expeditionary campaign which combines rapid access drilling and borehole logging may be indispensable for prospecting purposes.

The USA has maintained a presence at South Pole since 1956, culminating in the modern year-round research station. Efforts are underway to develop an intermediate coring drill and recover a ∼1500 m South Pole ice core, aimed at sampling atmospheric gases of the last ∼40 ka (personal communication from E. Saltzmann, 2011). If drilled to bedrock a core would likely obtain ice from the Eemian period, although we cannot exclude stratigraphic disturbance in the bottom few hundred meters. An ice core offers potential synergies with IceCube and other South Pole physics projects such as the Askaryan Radio Array, a prototype ultra-high-energy neutrino detector. Core samples could be of particular interest to radio experiments for characterizing the soluble ionic impurities, ice fabric, density, etc., that affect radio clarity (Reference Kravchenko, Besson, Ramos and RemmersKravchenko and others, 2011). South Pole core samples can be stored on site and could in principle be drilled during winter. A number of shallow South Pole cores have already been retrieved, the longest 361 m (Reference Palais, Mosley-Thompson and ThomasPalais and others, 1987) and a few thousand years in age, and the new core need not be far removed from South Pole Station to avoid anthropogenic contamination. If the main core is drilled near the astrophysics arrays, the remnant borehole could serve as an access point for optical and radio calibration beacons.