Hostname: page-component-7b7567c8c-z4zkx Total loading time: 0 Render date: 2026-11-17T08:30:51.242Z Has data issue: false hasContentIssue false

The motion of a layer of yield-stress material on an oscillating plate

Published online by Cambridge University Press:  22 March 2023

Edward M. Hinton
Affiliation:
School of Mathematics and Statistics, The University of Melbourne, Victoria 3010 Australia
Jesse F. Collis
Affiliation:
School of Mathematics and Statistics, The University of Melbourne, Victoria 3010 Australia
John E. Sader*
Affiliation:
Graduate Aerospace Laboratories, California Institute of Technology, Pasadena, CA 91125 USA
*
†Email address for correspondence: jsader@caltech.edu

Abstract

The motion of a finite layer of Bingham material on a solid plate that executes in-plane oscillations was reported previously by Balmforth et al. (J. Non-Newtonian Fluid Mech., vol. 158, issue 1–3, 2009, pp. 46–53). There, it was suggested that multiple yielded regions may arise within the material; this contrasts to start-up flow of the same material for which only one yielded region is generated. Here, we explore quantitatively the fluid physics of this oscillatory flow problem through analytical approximations and further numerical computation. Four new key topological properties concerning the generation and termination of the yielded regions are reported. It is shown that the existence of multiple yielded regions is equivalent to the layer never becoming entirely rigid during the periodic motion. For small inertia, the flow is approximately time-reversible with only a single yielded region generated at the plate. For large inertia, shear stress in the material decays rapidly as a function of distance from the plate. A thin zone of yielded material detaches periodically from the plate, and subsequently terminates within the layer. At high oscillation frequency, there can be any number $N$ of distinct rigid regions, satisfying $N= \lfloor 1- {\rm \pi}^{-1} \log B \rfloor$ where $B$ is the Bingham number. It is also shown that for $B>0.5370$, there are at most one yielded region and one rigid region throughout the motion. These theoretical results can be used as a basis for oscillatory rheometry, allowing for measurement of the yield stress using existing apparatus.

Information

Type
JFM Papers
Copyright
© The Author(s), 2023. Published by Cambridge University Press
Figure 0

Table 1.Key findings and formulas for the oscillatory motion of a layer of Bingham material.

Figure 1

Figure 1.Schematic of the flow problem and example velocity profiles for (a) Newtonian fluid, (b) Bingham material with low-frequency plate oscillations relative to the time scale for momentum diffusion, and (c) Bingham material with higher-frequency oscillations.

Figure 2

Figure 2.Velocity field (colour scales) and yield surfaces (black lines) of the periodic flow for nine pairs $(\alpha,B)$ obtained using the arbitrary-$B$ numerical solution. The yield surfaces separate rigid and yielded regions as labelled in (d); similar labelling of the other panels is implied.

Figure 3

Figure 3.Schematic illustration showing qualitative behaviour of the yield surfaces; not calculated using the arbitrary-$B$ numerical solution. (a) Case of at most one yield surface. (b) Case of two or more yield surfaces co-existing, an example of which is indicated by the vertical red dashed line. On the boundary of the first yielded region, the propagation direction of the yield surfaces is indicated by arrows, emanations by red circles, and collisions by open red squares.

Figure 4

Figure 4.Free-surface velocity $u = u_R$ (solid coloured lines), and the plate velocity $u=\cos t$ (solid black line) for (a) $B=0.6$, and (b) $B=0.8$, for two values of the oscillatory Reynolds number $\alpha$. The straight green dashed line gives the fastest (or slowest) possible motion of the rigid region, as per (3.14). (c,d) Corresponding plots of the yield surface. The vertical dashed lines are at the yield times $t_y=\sin ^{-1} B$ and $t=t_y +{\rm \pi}$, from (3.5).

Figure 5

Figure 5.Yield surfaces for $\alpha =0.05$ and three values of $B$. The arbitrary-$B$ numerical solution (black line) is compared to the asymptotic solution for small $\alpha$, (4.3) (red dashed line).

Figure 6

Figure 6.Maximum height of the uppermost yield surface for $B=0.05$. The black crosses are the arbitrary-$B$ numerical solution, the red line is (4.9) for small and moderate $\alpha$, and the blue line is (4.29a,b) for large $\alpha$.

Figure 7

Figure 7.Relationship between the phase shift $\sigma$ of the uppermost yield surface and the oscillation frequency $\alpha$, according to (4.8).

Figure 8

Figure 8.Yield surface for small Bingham number, $B=0.1$. (a–c) Smaller frequency values. The arbitrary-$B$ numerical solution (black line) is compared to the asymptotic solution (4.7) (red dashed line). (d–f) Larger frequency values. The yield surface does not come close to the free surface, and (4.3) is not valid (its solution is not shown). The red circles represent the times from (4.14) when yield surfaces are predicted to emanate from the plate.

Figure 9

Figure 9.Yield surfaces for $B=0.001$ with (a) $\alpha =25$, (b) $\alpha =100$. Straight lines are the yield surfaces according to (4.21). Red circles are the times in (4.14) when yield surfaces emanate from the plate. In (a), the red dashed lines are (4.7).

Figure 10

Figure 10.Relationship between the phase shift $\gamma$ of the yield surface collision/emanation at the plate and the oscillation frequency $\alpha$, according to (4.13).

Figure 11

Figure 11.Phase diagram showing the number of yield surfaces as a function of the oscillation frequency $\alpha$ and Bingham number $B$, calculated using the arbitrary-$B$ numerical solution (black line) and the approximation in (4.19) (red dot-dashed line).

Figure 12

Figure 12.Yield surfaces for $B=0.05$ and $\alpha =400$ (black lines are the arbitrary-$B$ numerical solution). The blue dot-dashed line is (4.28). The prediction for the second yield surface (red dashed line) is given by (4.35), and the third yield surface (green dotted line) is given by (4.39).

Figure 13

Figure 13.(a) Yield surfaces for $\alpha =200$ and four values of $B$ (only one yield surface in the time evolution is shown). (b) Yield surfaces for $B=0.4$ and $\alpha =50, 100, 200, 400$, rescaled to demonstrate that $Y \sim 1/\sqrt {\alpha }$ for $\alpha \gg 1$.

Figure 14

Figure 14.Shear stress at the plate, corresponding to figure 2. The horizontal dotted lines correspond to the yield stress, $\tau = \pm B$.

Figure 15

Figure 15.(a) Velocity $u(y,t)$ at $t=0, {\rm \pi}/8, 2{\rm \pi} /8, 3{\rm \pi} /8, 4{\rm \pi} /8, 5{\rm \pi} /8, 6{\rm \pi} /8, 7{\rm \pi} /8$ for $\alpha =1$ and $B=0.5$. (b) Location of the yield surface for $\alpha =1$ and $B=0.9$, $0.7$ and $0.5$. The red dashed lines show the asymptotic prediction (C14). (c) Difference between the velocity of the plate and the free surface for $\alpha =1$ and $B=0.5$ and $0.7$. The red dashed lines show the asymptotic prediction (C15).

Figure 16

Figure 16.Yield surface for $\alpha =10$ and $B=0.6$ calculated using the arbitrary-$B$ numerical solution (black curve). The asymptotic solutions of Appendix D, for emanation and collision of the yield surface, are shown as red curves. The collision time is $t_c = 3.09$ (calculated using the arbitrary-$B$ numerical solution), from which we find $\eta _Y =1.70$.