Hostname: page-component-7b7567c8c-wxvwp Total loading time: 0 Render date: 2026-11-16T23:58:42.106Z Has data issue: false hasContentIssue false

Falling film on an anisotropic porous medium

Published online by Cambridge University Press:  25 August 2022

Sanghasri Mukhopadhyay
Affiliation:
Université Savoie Mont Blanc, CNRS, LOCIE, 73000 Chambéry, France
Nicolas Cellier
Affiliation:
Université Savoie Mont Blanc, CNRS, LOCIE, 73000 Chambéry, France
Usha R
Affiliation:
Department of Mathematics, IIT Madras, Chennai, 600036 Tamil Nadu, India
Marx Chhay
Affiliation:
Université Savoie Mont Blanc, CNRS, LOCIE, 73000 Chambéry, France
Christian Ruyer-Quil*
Affiliation:
Université Savoie Mont Blanc, CNRS, LOCIE, 73000 Chambéry, France
*
†Email address for correspondence: christian.ruyer-quil@univ-smb.fr

Abstract

The stability and dynamics of a falling liquid film over an anisotropic porous medium are studied using a one-domain approach. Our stability analysis shows a significant departure from the effective no-slip boundary condition in the isotropic case. Anisotropy does not affect the threshold of linear instability. However, a non-trivial dual effect of anisotropy on the film stability is observed depending on the permeability of the porous medium. This dual effect results from the net balance of the enhancement of viscous diffusion at the top Brinkman sublayer and the mitigation of viscous damping in the core Darcy sublayer. Three-equation models have been derived from the lubrication theory approximation in terms of the exact mass balance and averaged momentum balances in the porous and liquid layers. In the nonlinear regime, anisotropy has a dual effect by damping capillary waves at large permeabilities and enhancing them at low permeabilities. Anisotropy also affects wave speeds and shapes, modifies travelling-wave branches of solutions, affects the development of a time-periodic wavetrain by inlet forcing and alters the noise-driven dynamics of the flow. These effects result from the mitigation of mass exchange at the liquid–porous interface and the contribution of the cross-stream permeability in the Brinkman top sublayer to the viscous diffusion.

Information

Type
JFM Papers
Copyright
© The Author(s), 2022. Published by Cambridge University Press
Figure 0

Figure 1.Schematic diagram of a falling film over an anisotropic saturated porous medium.

Figure 1

Figure 2.Base-flow velocity profiles $U_B(y)$ and approximated base-flow velocity profiles $\widetilde {U}(y)$ as functions of the cross-stream coordinate $y$ for different permeabilities, when $\varepsilon _H = 0.78$, $\varDelta = 0.001$, and (a) $\delta = 0.5$ and (b) $\delta = 0.1$.

Figure 2

Figure 3.Marginal stability curves corresponding to the Orr–Sommerfeld eigenvalue problem for different permeabilities and different anisotropy parameters, when $\varepsilon _H = 0.78$, $\delta = 0.5$, $\varDelta = 0.001$, $\theta = 4.6^{\circ }$ and ${Ka = 769.8}$: (a) $Da = 0.001$ and (b) $Da = 0.01$.

Figure 3

Figure 4.Spatial growth rate for different permeabilities and different anisotropy parameters, when $\varepsilon _H = 0.78$, $\delta = 0.5$, $\varDelta = 0.001$, $\theta = 4.6^{\circ }$, $Ka = 769.8$ and $Re = 50$: (a) $Da = 0.001$ and (b) $Da = 0.01$.

Figure 4

Figure 5.Marginal stability curves for different thicknesses of an anisotropic porous layer for different Darcy values and different $\xi$ values: dimensional cut-off frequency $f_c$ versus dimensional flow rate $q_N$, for $\varepsilon _H = 0.78$, $\varDelta = 0.001$, $\theta = 4.6^{\circ }$ and (a) $\delta = 0.5$, $\xi = 1$, (b) $\delta = 0.5$, $\xi = 1000$, (c) $\delta = 0.1$, $\xi = 1$ and (d) $\delta = 0.1$, ${\xi = 1000}$. ‘OS solid’ refers to an impermeable no-slip boundary.

Figure 5

Figure 6.Comparisons of the marginal stability curves for the two-equation full (4.2), (4.14), three-equation full (4.2), (4.10), and approximate model (4.17), (4.16), with the Orr–Sommerfeld analysis. All the curves are plotted with the parameter set $\varepsilon _H = 0.78$, $\delta = 0.5$, $\varDelta = 0.001$, $Ka = 769.8$ and $\theta = 4.6 ^{\circ }$: (a) $Da = 0.01$, $\xi = 1000$; and (b) $Da = 0.001$, $\xi = 1000$.

Figure 6

Figure 7.Bifurcation diagrams of the TW solutions to the three-equation full model (4.2), (4.10) in the plane of velocity $c$ versus dimensional frequency $f$. The Reynolds number $R = q_N/\nu$ based on the flow rate at the inlet is: (a) $Re = 33.8\ (R = 15)$, (b) $Re = 36\ (R = 16)$, (c) $Re = 42.8\ (R = 19)$ and (d) $Re = 45.5\ (R = 20.2)$. Parameters are $Da = 0.01$, $\varepsilon _H = 0.78$, $\delta = 0.5$, $\varDelta = 0.001$, $\theta = 4^\circ$, $Ka = 2340$ and $\nu = 2.3\times 10^{-6}\ \textrm {m}^2\ \textrm {s}^{-1}$.

Figure 7

Figure 8.Wave profiles of the TW solutions to the three-equation full model (4.2), (4.10) corresponding to the different wave families indicated in figure 7(d): the (a) $\gamma _2$, (b) $\gamma _1$, (c) $\gamma _1'$ and (d) $\gamma _1''$ wave families. Here $\lambda$ corresponds to the period. Parameters are $Da = 0.01$, $\varepsilon _H = 0.78$, $\delta = 0.5$, $\varDelta = 0.001$, $\theta = 4^\circ$, $Ka = 2340$, $Re = 45.5\ (R = 20.2)$, frequency $f=1$ Hz and $\nu = 2.3\times 10^{-6}\ \textrm {m}^2\ \textrm {s}^{-1}$.

Figure 8

Figure 9.The same as figure 7 except for $Da = 0.001$: (a) $Re = 42.8\ (R = 19)$ and (b) $Re = 45.5\ (R = 20.2)$.

Figure 9

Figure 10.Bifurcation diagrams of the TW solutions to the three-equation approximate model (4.17), (4.16) at $Re=42.8$: (a) $Da=0.01$ and (b) $Da=0.001$. The other parameters are identical to those in figure 7.

Figure 10

Figure 11.Nonlinear TWs for the two-equation full (4.2), (4.14), and three-equation full (4.2), (4.10), and approximate (4.17), (4.16) models, and for the no-slip model (4.17), (4.19) (impermeable wall at $y = \delta -\delta _B$), when $\varepsilon _H = 0.78$, $\delta = 0.5$, $\varDelta = 0.01$, $Ka = 769.8$, $\theta = 4.6 ^{\circ }$ and $\lambda = 200$. Here $H$ indicates the thickness of the entire layer (porous and liquid). (a) $Da = 0.01$, $\xi = 1$; (b) $Da = 0.01$, $\xi = 1$; (c) $Da = 0.01$, $\xi = 1000$; and (d) $Da = 0.01$, $\xi = 1000$.

Figure 11

Figure 12.Simulations of a wave-train generated by a periodic inlet forcing using the no-slip model (4.17), (4.19), and the three-equation full and approximate models (4.2), (4.10), and (4.17), (4.16). Parameters correspond to an experiment conducted by Liu & Gollub (1994): $Re=47.3$, $f=4.5$ Hz, $\theta = 6.4^\circ$, ${\nu =6.27}\times 10^{-6}\ \textrm {m}^2\ \textrm {s}^{-1}$ and $Ka=526$.

Figure 12

Figure 13.Simulations of a wave-train generated by a periodic inlet forcing using the three-equation full model (4.2), (4.10) and the no-slip model (4.17), (4.19) for different Darcy numbers. Parameters correspond to an experiment conducted by Liu & Gollub (1994): $Re=47.3$, $f=1.5$ Hz, $\theta = 6.4^\circ$, $\nu =6.27\times 10^{-6}\ \textrm {m}^2\ \textrm {s}^{-1}$ and $Ka=526$. (a) $Da = 0.001$ and (b) $Da = 0.01$.

Figure 13

Figure 14.Simulations of the response of the film to noise at the inlet based on the three-equation full model (4.2), (4.10) and the no-slip model (4.17), (4.19). Panels ($a$) and ($b$) are snapshots of the free-surface elevation and flow rates in the liquid and porous region at the end of the simulation. Parameters are $Da = 0.01$, ${\varepsilon _H = 0.78}$, $\delta = 0.5$, $\varDelta = 0.001$, $Ka = 769.8$ and $\theta = 4.6^{\circ }$.