Hostname: page-component-7b7567c8c-wxvwp Total loading time: 0 Render date: 2026-11-16T05:52:59.292Z Has data issue: false hasContentIssue false

Nonlinear wave attenuation in strongly confined falling liquid films sheared by a laminar counter-current gas flow

Published online by Cambridge University Press:  03 January 2023

Sophie Mergui*
Affiliation:
Université Paris-Saclay, CNRS, FAST, 91405 Orsay, FranceSorbonne Université, UFR 919, 4 place Jussieu, F-75252 Paris CEDEX 05, France
Gianluca Lavalle
Affiliation:
Mines Saint-Etienne, Université Lyon, CNRS, UMR 5307 LGF, Centre SPIN, F-42023 Saint-Etienne, France
Yiqin Li
Affiliation:
Université Paris-Saclay, CNRS, FAST, 91405 Orsay, France
Nicolas Grenier
Affiliation:
Université Paris-Saclay, CNRS, LISN, 91405 Orsay, France
Georg F. Dietze
Affiliation:
Université Paris-Saclay, CNRS, FAST, 91405 Orsay, France
*
†Email address for correspondence: sophie.mergui@sorbonne-universite.fr

Abstract

Experiments are conducted in water films falling along the bottom wall of a weakly inclined rectangular channel of height $5$ mm in the presence of a laminar counter-current air flow. Boundary conditions have been specifically designed to avoid flooding at the liquid outlet, thus allowing us to focus on the wave dynamics in the core of the channel. Surface waves are excited via coherent inlet forcing before they come into contact with the air flow. The effect of the air flow on the height, shape and speed of two-dimensional travelling nonlinear waves is investigated and contrasted with experiments of Kofman, Mergui & Ruyer-Quil (Intl J. Multiphase Flow, vol. 95, 2017, pp. 22–34), which were performed in a weakly confined channel. We observe a striking difference between these two cases. In our strongly confined configuration, a monotonic stabilizing effect or a non-monotonic trend (i.e. the wave height first increases and then diminishes upon increasing the gas flow rate) is observed, in contrast to the weakly confined configuration where the gas flow is always destabilizing. This stabilizing effect implies the possibility of attenuating waves via the gas flow and it confirms recent numerical results obtained by Lavalle et al. (J. Fluid Mech., vol. 919, 2021, R2) in a superconfined channel.

Information

Type
JFM Papers
Copyright
© The Author(s), 2023. Published by Cambridge University Press
Figure 0

Figure 1.Sketch of the experimental set-up. The liquid loop appears in blue and the gas path is highlighted by a red arrows in the channel gap.

Figure 1

Figure 2.Sketch of the channel cross-section.

Figure 2

Figure 3.Film thickness time trace measured with the CCI technique. Here $\textit {Re}_l=35$, $f=2.8$ Hz, $\eta _0=11.1$, without counter-current gas flow. (a) The blue line corresponds to the time-averaged film thickness over the duration of the signal. Open and filled circles correspond to the minimal and maximal height of each wave in the signal, respectively. (b) Enlargement of the signal presented in (a). Squares and downward triangles mark the maximum positive free-surface slope magnitude, located at the back of the first capillary wave and at the main wave tail. Upward triangles mark the maximum negative free-surface slope magnitude, located at the main wavefront.

Figure 3

Figure 4.Typical experiment: $\textit {Re}_l=35$, $f=2.8$ Hz, $\eta _0=11.1$, without counter-current gas flow (aerostatic case). (a) Visualization of the gas–liquid interface over the entire test section. The white arrow marks the length over which spatiotemporal diagrams are constructed. The filled white circle marks the location for the CCI measurements ($x=60$ cm). (b) Spatiotemporal diagram obtained using a linear camera located in the midplane ($z=13.5$ cm).

Figure 4

Figure 5.Streamwise evolution of the time-averaged film thickness, $h_m$, along the central axis of the channel, in the aerostatic case ($\textit {Re}_g=0$, empty circles) and with counter-current gas flow ($\textit {Re}_g=942$ ($u_g=3.05\ {\rm m}\ {\rm s}^{-1}$), filled circles). The horizontal dashed-line indicates the Nusselt thickness (flat-surface film thickness without gas flow) associated with the prescribed liquid Reynolds number. The opening slot through which ambient air is sucked spans from $x=39$ cm to $x=42$ cm (highlighted by vertical dot-dash lines). Here $\textit {Re}_l=35$, $f=2.8$ Hz, $\eta _0=11$.

Figure 5

Figure 6.(a,c,e) Shadowgraphs of the gas–liquid interface over the entire test section for three different gas velocities, (b,d, f) associated spatiotemporal diagrams. Here (a,b) $u_g=1.9\ {\rm m}\ {\rm s}^{-1}$ ($\textit {Re}_g=587$), (c,d) $u_g=3.4\ {\rm m}\ {\rm s}^{-1}$ ($\textit {Re}_g=1023$), (e, f) $u_g=4.1\ {\rm m}\ {\rm s}^{-1}$ ($\textit {Re}_g=1242$). These figures are the continuation of the aerostatic case ($u_g=0$) presented in figure 4. The white dot and arrow are the same as those described in the caption of figure 4. Here $\textit {Re}_l=35$, $f=2.8$ Hz, $\eta _0=11.1$.

Figure 6

Figure 7.Influence of the gas velocity $u_g$ on nonlinear wave profiles for two confinement levels: $\eta _0=39$ ($H=19$ mm) and $\eta _0=11.1$ ($H=5.2$ mm); $\textit {Re}_l=35$, $f=2.8$ Hz, $x=60$ cm. Here (a) $\eta _0 = 39$, $u_g = 0\ {\rm m}\ {\rm s}^{-1}$; (b) $\eta _0 = 39$, $u_g = 3.3\ {\rm m}\ {\rm s}^{-1}$; (c) $\eta _0 = 39$, $u_g = 4.4\ {\rm m}\ {\rm s}^{-1}$; (d) $\eta _0 = 11.1$, $u_g = 0\ {\rm m}\ {\rm s}^{-1}$; (e) $\eta _0 = 11.1$, $u_g = 3.4\ {\rm m}\ {\rm s}^{-1}$; ( f) $\eta _0 = 11.1$, $u_g = 4.4\ {\rm m}\ {\rm s}^{-1}$.

Figure 7

Figure 8.Influence of the gas velocity $u_g$ on: (a) wave celerity $c$, (b) minimum $h_{min}$ (downward triangles), mean $h_{m}$ (squares) and maximum $h_{max}$ (circles) film thickness for $\eta _0=39$, $\eta _0 =11.1$ and $\eta _0 =9.9$ (white, grey and black symbols, respectively). Here $\textit {Re}_l=35$, $f=2.8$ Hz, $x=60$ cm. Error bars are drawn for all symbols, but most of them are shorter than the symbol size in panel (b) and thus invisible.

Figure 8

Figure 9.Influence of the gas velocity $u_g$ on $\delta _{max}$ (3.1) for $\eta _0=39$, $\eta _0 =11.1$ and $\eta _0 =9.9$ (white, grey and black symbols, respectively). Here $\textit {Re}_l=35$, $f=2.8$ Hz, $x=60$ cm.

Figure 9

Figure 10.Influence of the gas velocity $u_g$ on nonlinear wave profiles measured at $x=60$ cm for $\textit {Re}_l=35$, $f=2.8$ Hz, $\eta _0=9.9$, corresponding to the experiment presented in figure 9 (black symbols). Here (a) $u_g = 0\ {\rm m}\ {\rm s}^{-1}$; (b) $u_g = 0.8\ {\rm m}\ {\rm s}^{-1}$; (c) $u_g = 1.6 {\rm m}\ {\rm s}^{-1}$; (d) $u_g = 2.1\ {\rm m}\ {\rm s}^{-1}$; (e) $u_g = 2.4\ {\rm m}\ {\rm s}^{-1}$; ( f) $u_g = 2.7\ {\rm m}\ {\rm s}^{-1}$; (g) $u_g = 2.9\ {\rm m}\ {\rm s}^{-1}$; (h) $u_g = 3.1\ {\rm m}\ {\rm s}^{-1}$; (i) $u_g = 3.4\ {\rm m}\ {\rm s}^{-1}$; (j) $u_g = 3.7\ {\rm m}\ {\rm s}^{-1}$; (k) $u_g = 3.8\ {\rm m}\ {\rm s}^{-1}$; (l) $u_g = 4\ {\rm m}\ {\rm s}^{-1}$.

Figure 10

Figure 11.Influence of the gas velocity $u_g$ in (a) and the normalized gas velocity $\hat {c}$ (3.2) in (b), on the maximum positive free-surface slope $\mathrm {max}\{\partial _xh\}$ at the back of the first capillary ripple (squares) and at the main hump tail (downward triangles), and on the maximum negative slope $\mathrm {min}\{\partial _xh\}$ at the front of the main hump (upward triangles), for $\eta _0=39$ (white symbols) and $\eta _0 =11.1$ (grey symbols). The number of capillary ripples is indicated. Vertical dashed lines in (b) indicate the values of $\hat c$ related to the wave profiles presented in figure 12. Here $f=2.8$ Hz, $\textit {Re}_l=35$, $x=60$ cm.

Figure 11

Figure 12.Influence of the confinement on wave profiles at given values of $\hat {c}$ (3.2) marked by vertical dashed lines in figure 11(b). Here (a) $\hat {c}=0.13$; (b) $\hat {c}=0.23$. Thin solid line, $\eta _0=39$ ($u_g=4.4\ {\rm m}\ {\rm s}^{-1}$ in (a) and $5.5\ {\rm m}\ {\rm s}^{-1}$ in (b)); thick solid line, $\eta _0=11.1$ ($u_g=2.8\ {\rm m}\ {\rm s}^{-1}$ in (a) and $4\ {\rm m}\ {\rm s}^{-1}$ in (b)). Same parameters as in figure 11.

Figure 12

Figure 13.Wave profiles for different values of the liquid Reynolds number $\textit {Re}_l$ and forcing frequency $f$ in the strongly confined channel for the aerostatic case. From left to right, the resulting wavelength is $6.5$ cm ($\textit {Re}_l=22$), $6.5$ cm ($\textit {Re}_l=35$), $7.3$ cm ($\textit {Re}_l=44.6$), not available for $\textit {Re}_l=49$. Here (a) $R_l = 22$, $f = 2.2\ {\rm Hz}$, (b) $R_l = 35$, $f = 2.8\ {\rm Hz}$, (c) $R_l = 44.6$, $f = 2.8\ {\rm Hz}$, (d) $R_l = 49$, $f = 3.05\ {\rm Hz}$.

Figure 13

Figure 14.Influence of the liquid Reynolds number $\textit {Re}_l$ on: (a) wave celerity, $\textit {Re}_l=22$, $\eta _0=11.5$ (white triangles) – $\textit {Re}_l=35$, $\eta _0=11.1$ (black triangles) – $\textit {Re}_l=44.6$, $\eta _0=10.3$ (grey triangles); (b) $\delta _{max}=h_{max}/h_{m}$, same parameters as (a) for white and grey triangles, $\textit {Re}_l=35$, $\eta _0=9.9$ (black circles) – $\textit {Re}_l=49$, $\eta _0=10.3$ (crosses). strongly confined channel.

Figure 14

Figure 15.Influence of the liquid Reynolds number $\textit {Re}_l$ on the local confinement parameter $\eta _{max}$ (3.3) in the strongly confined channel. Same parameters as in figure 14(b).

Figure 15

Figure 16.Relative mean film thickness $\hat {h}$ (3.5) measured in the $H \approx 5$ mm channel and in the $H \approx 19$ mm channel (Kofman et al.2017, square symbols), as a function of: (a) the Froude number $Fr_{g,l}$ (3.4); (b) the modified Froude number, $Fr_{fric}$ (3.6). The solid (laminar gas flow) and dashed (turbulent gas flow) curves correspond to the flat-film solution $\hat {h}_{flat}$ according to (B13) with $\epsilon =0$ ($\hat {h}_{flat}=\tilde {h}_{flat}-1$).

Figure 16

Figure 17.Location of the anemometer used to measure the air velocity at the end of the channel (gas inlet).

Figure 17

Figure 18.Air velocity profiles measured for different fan powers (in Watts) in the dry channel: $P_f=1.3$ (circles); $3.9$ (squares); $6.5$ (upward triangles); $7.8$ (downward triangles); $10.4$ (open circles); and $13$ (open squares). Solid lines correspond to polynomial fits. Here $\beta =4.9^{\circ }$.

Figure 18

Figure 19.Calibration curve used to quantify the gas flow rate $q_g$ (A1) per unit of channel width from the imposed fan power $P_f$. Here $\beta =4.9^{\circ }$.

Figure 19

Table 1.Ratio between the mean and the maximum air velocity issued from the measured velocity profiles (black symbols in figure 18) and the corresponding aerodynamic entry lengths given by (A2).

Figure 20

Figure 20.Here $\textit {Re}_g$ (filled circles) and $\textit {Re}_{g}^{lam}$ (open circles) as a function of the fan power $P_f$. Here $\textit {Re}_g$ is calculated by integrating velocity profiles measured at the end of the channel (figure 18), and $\textit {Re}_{g}^{lam}$ from the maximum velocity measurements performed in the fully developed region and assuming a laminar parabolic profile, i.e. $u_g = 2/3 u_{max}$.

Figure 21

Figure 21.(a) Global skin-friction coefficients at the liquid–gas interface $C_{f,i}$ (B7) (red line) and at the upper wall of the channel $C_{f,w}$ (B8) (blue line) as a function of $\textit {Re}_g$, calculated from the fully coupled primary flow solution. The black line corresponds to a skin-friction coefficient in the case of a static interface (i.e. $\epsilon =0$). (b) Ratio between the interface velocity and the gas velocity $u_0/u_g = -\epsilon$. $\textit {Re}_l=22$ (dashed lines) and $\textit {Re}_l=44.6$ (solid lines), $\beta =4.9^{\,\circ }$, $H=5.2$ mm.

Figure 22

Figure 22.Gas velocity profiles calculated from the fully coupled primary flow solution for $\textit {Re}_l=22$: $u(Y)/u_{max}$ with $u(Y)$ according to (B1) and $u_{max}=\min (u(Y))<0$. Dash–dot line, $u_0/u_g=1$ ($\textit {Re}_g=24.3$); dashed line, $u_0/u_g=0.3$ ($\textit {Re}_g=80$); solid line, $u_0/u_g=0.16$ ($\textit {Re}_g=145$); thick solid line, $u_0=0$ (Poiseuille flow). The location of $u_{max}$ in the channel, $Y_{max}=Y(u_{max})$, is plotted in the inset as a function of $\textit {Re}_g$ ($Y_{max}=0.5$ for a Poiseuille flow). Open circles mark $Y_{max}$ for the profiles represented in the figure (except the Poiseuille flow). Here $\beta =4.9^{\circ }$, $H=5.2$ mm.

Figure 23

Figure 23.Thickness of a flat-surface film (normalized by the Nusselt thickness $h_N$) subject to a counter-current laminar gas flow, obtained from the flat-film model (triangles) (according to (B13) with $\epsilon =0$) compared with the numerical solution of the fully coupled two-phase primary flow (solid lines). The normalized mean film thickness $\tilde h_{exp}=h_m/h_N$ measured in the experiments is also reported (circles). Here $\textit {Re}_l=22$ (white symbols) and $\textit {Re}_l=44.6$ (grey symbols), $\beta =4.9^{\circ }$, $H=5.2$ mm.