Hostname: page-component-7b7567c8c-2n9c9 Total loading time: 0 Render date: 2026-11-16T17:44:45.757Z Has data issue: false hasContentIssue false

The influence of shock speed variation on radiation and thermochemistry experiments in shock tubes

Published online by Cambridge University Press:  16 September 2022

Peter L. Collen*
Affiliation:
Oxford Thermofluids Institute, Southwell Building, Osney Mead, Oxford OX2 0ES, UK
Matthew Satchell
Affiliation:
Oxford Thermofluids Institute, Southwell Building, Osney Mead, Oxford OX2 0ES, UK
Luca Di Mare
Affiliation:
Oxford Thermofluids Institute, Southwell Building, Osney Mead, Oxford OX2 0ES, UK
Matthew McGilvray
Affiliation:
Oxford Thermofluids Institute, Southwell Building, Osney Mead, Oxford OX2 0ES, UK
*
†Email address for correspondence: peter.collen@eng.ox.ac.uk

Abstract

Shock tubes are a crucial source of experimental data for the aerothermodynamic modelling of atmospheric entry vehicles. Notably, many chemical-kinetic and radiative models are validated directly against optical measurements from these facilities. Typically, the incident shock speed at the location of the experimental measurement is taken to be representative of the test slug; however, the shock velocity can vary substantially upstream of this location. These variations have been long posited as a source of disagreement with computational predictions, although a definitive link has proved elusive. This work describes a series of experiments which aim to isolate and confirm the importance of the shock deceleration effect. This is achieved by generating different shock trajectories and comparing the post-shock trends in atomic oxygen emission and electron density. These trends are shown to be directly linked to the upstream shock speed variations using a recently developed numerical tool (LASTA). The close agreement of the comparisons confirms the importance of shock speed variation for shock tube experiments; these findings have direct and potentially critical relevance for all such studies, both past and present.

Information

Type
JFM Papers
Copyright
© The Author(s), 2022. Published by Cambridge University Press
Figure 0

Figure 1.Diagram demonstrating the effect of shock deceleration on post-shock equilibrium in the EAST facility. The upper diagram shows the variation in shock speed and the downstream movement of the shocked gas. The lower diagram represents the test slug as imaged when the shock is at the observation window. Adapted from Brandis et al. (2010a).

Figure 1

Figure 2.Diagram of T6 in AST mode, including a distance–time diagram of the main wave processes which occur during a test. Unsteady expansions are denoted ‘us-x’ and steady expansion regions by ‘s-x’. The valid test flow is marked in red and the nominal test time by ‘$\tau$’.

Figure 2

Figure 3.Diagram of emission spectroscopy arrangement at the AST windows. Not to scale.

Figure 3

Figure 4.Example of the mechanisms used to vary the experimental shock speed profile. The upper graph shows the impact of varying secondary driver fill pressure with all other parameters held constant. The lower graph demonstrates the impact of the secondary diaphragm thickness; this diaphragm is located between shock tube 1 and the nozzle.

Figure 4

Figure 5.The variation in equilibrium electron density with shock speed, calculated using the CEA program. Adapted from Brandis et al. (2010a).

Figure 5

Figure 6.Measured SSV for the SSV radiance test cases explored in this work. In all cases, the AST fill composition was 26.6 Pa of synthetic air. Lines are included here for ease of identification of each trajectory.

Figure 6

Table 1.Measured shock speed characteristics for the SSV radiance test cases, all at an initial fill pressure of 26.6 Pa. Here, $U_{s,f}$ is the final shock speed, $U_{s,m}$ the mean of the last three measurements and $\Delta U_{s,max}$ the maximum percentage variation of the profile from the final measurement.The absolute NEM ($K_{a}$) is calculated from 700–850 nm. The units for velocity and absolute NEM are km s$^{-1}$ and W cm$^{-2}$ sr$^{-1}$, respectively.

Figure 7

Figure 7.Experimental results of oxygen 777 nm multiplet emission for the radiance test cases.

Figure 8

Figure 8.Comparison of the experimentally measured spatial variation in atomic oxygen radiance with the predictions of the coupled NEQAIR/LASTA simulations. All data have been referenced to the same shock location. A premature termination of the experimental trace indicates the upstream edge of the field of view; the LASTA data ends at the rear of the simulated test slug. In all cases the LASTA points were initially distributed at 200 mm intervals along the shock tube.

Figure 9

Figure 9.Shock speed variation for Poshax3 comparison cases. The dashed line shows the mean value of the final three (filled) measurements.

Figure 10

Figure 10.Comparison of experimental oxygen 777 nm radiance with NEQAIR predictions. Simulations are performed with LASTA and with Poshax3 at the final and mean shock speeds. The initial Lagrange point spacing is 200 mm.

Figure 11

Figure 11.Numerical investigation of the influence of deceleration rate on the test slug length. The top half of the figure shows simulated shock speed profiles along the shock tube. The bottom half shows the resulting temperature trends through the shock layer. In all simulations the initial Lagrange point spacing is 200 mm.

Figure 12

Figure 12.Measured SSV for the T6 electron density measurements.

Figure 13

Table 2.Measured shock speed characteristics for the SSV electron density test cases. Here, $P$ is the shock tube initial fill pressure, $U_{s,f}$ is the final shock speed, $U_{s,m}$ the mean of the last three measurements and $\Delta U_{s,max}$ the maximum percentage variation of the profile from the final measurement.The absolute NEM ($K_{a}$) is calculated from 700–850 nm. The units for pressure and velocity are Pa and km s$^{-1}$, respectively.

Figure 14

Figure 13.Experimental electron density results at the 0.1 Torr condition. The stated shock velocities refer to the mean of the last three shock speed measurements. These are compared with the nominal equilibrium value (based on the averaged shock speed) and the predictions of LASTA. In both cases the LASTA results have been referenced to coincide with the shock location as determined from the rise in radiance. In both cases the initial Lagrange spacing was 200 mm.

Figure 15

Figure 14.Experimental electron density results at the 0.2 Torr condition. The stated shock velocities refer to the mean of the last three shock speed measurements. In all cases the LASTA results have been referenced to coincide with the start of the non-equilibrium peak and the initial Lagrange spacing was 200 mm.