Hostname: page-component-7b7567c8c-z4zkx Total loading time: 0 Render date: 2026-11-16T05:38:12.734Z Has data issue: false hasContentIssue false

Motion of self-rewetting drop on a substrate with a constant temperature gradient

Published online by Cambridge University Press:  29 March 2021

Ze-Lai Xu
Affiliation:
Department of Modern Mechanics, University of Science and Technology of China, Hefei 230026, PR China
Jun-Yuan Chen
Affiliation:
Department of Modern Mechanics, University of Science and Technology of China, Hefei 230026, PR China
Hao-Ran Liu
Affiliation:
Department of Modern Mechanics, University of Science and Technology of China, Hefei 230026, PR China
Kirti Chandra Sahu*
Affiliation:
Department of Chemical Engineering, Indian Institute of Technology Hyderabad, Sangareddy, 502 285 Telangana, India
Hang Ding*
Affiliation:
Department of Modern Mechanics, University of Science and Technology of China, Hefei 230026, PR China
*
†Email addresses for correspondence: ksahu@che.iith.ac.in, hding@ustc.edu.cn
†Email addresses for correspondence: ksahu@che.iith.ac.in, hding@ustc.edu.cn

Abstract

We investigate the dynamics of a self-rewetting drop placed on a substrate with a constant temperature gradient via three-dimensional numerical simulations using a conservative level-set approach to track the interface of the drop. The surface tension of a so-called self-rewetting fluid exhibits a parabolic dependence on temperature with a well-defined minimum. Two distinct drop behaviours, namely deformation and elongation, are observed when it is placed at the location of the minimum surface tension. The drop spreads slightly and reaches a pseudo-steady state in the deformation regime, while it continuously spreads until breakup in the elongation regime. Theoretical models based on the forces exerted on the drop have been developed to predict the critical condition at which the drop undergoes the transition between the two regimes, and the predictions are in good agreement with the numerical results. We also investigate the effect of the initial position of the drop with respect to the location of the minimum surface tension on the spreading and migration dynamics. It is found that, at early times, the migration of the drop obeys an exponential function with time, but it diverges at the later stage due to an increase in the drop deformation.

Information

Type
JFM Papers
Copyright
© The Author(s), 2021. Published by Cambridge University Press
Figure 0

Figure 1.(a) A schematic diagram showing the initial configuration of a self-rewetting sessile drop on a substrate with linear temperature variation. The $x$ and $y$ axes are shown, while the $z$ axis is vertical to the substrate. The length and width of the substrate are $6R$ (or $12 R$ in § 3.4) and $3R$, respectively. (b) Typical variations of the dimensionless surface tension coefficient $\gamma$ along the substrate for different values of $M_1$, with the centre of the drop being placed at $x=0$.

Figure 1

Figure 2.Grid-independent test for a self-wetting drop for mesh sizes of ${\rm \Delta} x=1/40, 1/80, 1/160$, with $M_1=1.0$, $\theta =60^\circ$, $Re=1$, $We=10^{-3}$, $Ma=0.7$, $\rho _r=10^{-3}$, $\mu _r=10^{-2}$ and $k_r=4 \times 10^{-2}$. (a) Temporal evolution of the wetted length of the drop $L_w$ and (b) the contact line of the drop at time $t=0.2$.

Figure 2

Figure 3.Illustration of different behaviours (deformation for $M_1=0.8$ and elongation for $M_1=1.0$) of a self-rewetting drop placed at $x_{mi}=0$ with $\theta =45^\circ$. The interface and contour of streamlines at $y=0$ when the droplet exhibits (a) deformation and (b) elongation behaviours. In each panel, the blue dashed line shows the initial interface and the red line represents the interface at a later time. (c,d) The three-dimensional shapes of the drop interface at $t=1.0$ and 0.6 in (a,b), respectively. Temporal evolution of the wetted length ($L_w$) of the drop exhibiting (e) deformation and (f) elongation behaviours.

Figure 3

Figure 4.Phase diagram showing the deformation and elongation regimes in terms of $M_1$ verses $\theta$ (in degrees). The values of $(M_1, \theta )$ exhibiting the regimes of drop deformation and elongation are designated by triangles and squares, respectively. The theoretical prediction of the boundary separating the two regimes is demonstrated by black solid line, and details can be found in § 3.3.

Figure 4

Figure 5.(a) Different forces acting on a quarter of the drop in the positive quadrant. The drop encounters the surface tension force $(F_{s1})$ from the $y$–$z$ symmetric plane, the force due to the contact line $(F_{s2})$, the capillary pressure $(F_p)$ at the $y$–$z$ symmetric plane and the viscous force $(F_\mu )$ from the substrate. We choose the slice between the dashed line and plane $AOC$ as the control volume to analyse the viscous stress at the centreline $OA$. (b) The micro control volume for the analysis of viscous stress near the contact line. The thick line represents the contact line. (c) A geometric sketch of a slice of the drop at the symmetric plane $AOC$ of length $L$ and height $H$. Here, $r_x$ denotes the radius of curvature of the arc $\widehat {AC}$. (d) The micro control volume at the interface for the analysis of stress boundary conditions.

Figure 5

Figure 6.Comparison of the numerically and theoretically obtained curvature at the top point of the interface and drop shapes in the (a) $x$–$z$ and (b) $y$–$z$ planes. Four sets of parameters are considered: $\theta =15^\circ$ and $M_1=0.1$; $\theta =30^\circ$ and $M_1=0.3$; $\theta =45^\circ$ and $M_1=0.8$; and $\theta =60^\circ$ and $M_1=1.2$. Numerically and theoretically obtained drop shapes are represented by solid and dashed lines, respectively.

Figure 6

Figure 7.Comparison of the viscous stress $\tau _{zx}$ obtained from theoretical prediction and numerical simulation. (a) At the contact line for $(\theta , M_1) = (30^\circ , 0.4)$ and (b) at the centreline $OA$ for different values of the contact angle $\theta$ and $M_1$, specifically $\theta =45^\circ$ and $M_1=$0.8, $\theta =30^\circ$ and $M_1=0.4$, $\theta =15^\circ$ and $M_1=0.1$.

Figure 7

Figure 8.(a) Typical variations of the viscous stress profiles for $n=1$, 2, 4, 8 and 16. (b) Comparison of the distribution of the viscous stress $\tau _{zx}$ between theory (lines) and numerical result (symbols) at $x= -0.2$ (red dashed line with square symbols), $-0.5$ (black solid line with circle symbols) and $-0.8$ (blue dash-dotted line with triangle symbols) for $\theta =30^\circ$ and $M_1=0.4$. The top-right inset shows the contour of the viscous stress $\tau _{zx}$ at the half-wetted area of the substrate, wherein the vertical lines represent the three typical positions chosen to demonstrate the $\tau _{zx}$ profiles.

Figure 8

Figure 9.The variations of the theoretically obtained dimensionless net external force $F_e$ as a function of $L$ at $\theta =30^\circ$ for different values of $M_1$. The grey dashed line indicates $F_e=0$, i.e. all the forces are balanced. Here $F_e<0$ and $F_e>0$ denote the drop retracting and spreading regions, respectively.

Figure 9

Figure 10.Temporal evolutions of (a,b) the drop and (c,d) the wetted area when the initial location is $x_{mi}=0.1$ and the value of the contact angle is $\theta =30^\circ$: (a,c) $M_1=0.3$ and (b,d) $M_1=0.6$. In (c,d), the shapes of the wetted area of the drop are shown at time intervals of $0.2$ starting from $t=0.1$.

Figure 10

Figure 11.Variations of the numerically obtained (a) centre of mass of the drop $x_m$ with $t$ and (b) $M_1 x_m$ with the velocity of the centre of mass of the drop $(U_m)$ for different values of $M_1$ for $\theta = 30^\circ$. Here, $x_{mi} = 0.1$ for all cases except the results presented by the thick grey dashed line in (b) for which $x_{mi}=0$ and $M_1=0.4$.

Figure 11

Figure 12.Variations of the wetted length of the drop $L_w$ versus $t$ for different values of $\theta$ and $M_1$ in the (a) deformation and (b) elongation regimes. Here, $x_{mi}=0.1$.

Figure 12

Figure 13.Variations of the wetted length $L_w$ with the $x$ coordinate of the centre of mass of the drop $x_m$ started from different initial locations on the substrate: (a) $M_1=0.3$ and $x_{mi}=0.1$, 0.2, 0.4, 0.6, 1.0 and 1.5; (b) $M_1=0.6$ and $x_{mi}=0.1$, 0.2, 0.4, 0.6. The values of $M_1t$ are at the points shown by the black dots. Here, $\theta =30^\circ$.