2 Experimental set-up and procedure

The experiments were performed in a pressure-controlled set-up. For details concerning the fabrication and use of the equipment, the reader is referred to Enríquez et al. (Reference Enríquez, Hummelink, Bruggert, Lohse, Prosperetti, van der Meer and Sun2013). To summarise, a mixing tank contained a mixture of liquid (ultra-pure water) and gas ( $\text{CO}_{2}$ ) saturated at a certain pressure $P_{0}\approx 9$ bars and temperature $T\approx 20\,^{\circ }\text{C}$ . The water was degassed by means of a vacuum pump prior to experiments to ensure that there were no other spurious gases in solution. The other (measurement) tank contained a silicon substrate which was held by a lateral clip. A preferential spot for bubbles to nucleate and grow was etched on its surface and was composed of black silicon (Stubenrauch et al. Reference Stubenrauch, Fischer, Kremin, Stoebenau and Albrecht2006; Borkent et al. Reference Borkent, Gekle, Prosperetti and Lohse2009; Liu et al. Reference Liu, Coxon, Peters, Hoex, Cole and Fray2014), a superhydrophobic material. Around this site (a pit of radius $R_{p}=50~\unicode[STIX]{x03BC}\text{m}$ ), a glass cylinder of radius $R_{c}=2.5~\text{mm}$ and height $H=10~\text{mm}$ was glued to the substrate by means of curing a hydrophilic resin with an ultraviolet light. A schematic of the set-up can be seen in figure 1, together with an experimental snapshot.

Figure 1.

(a) Schematic (not to scale) of the experimental geometry with the substrate holding the cylindrical lateral confinement of radius $R_{c}=2.5~\text{mm}$ and height $H=10~\text{mm}$ around the growing bubble. The single bubble grows from the superhydrophobic pit of radius $R_{p}=50~\unicode[STIX]{x03BC}\text{m}$ according to the imposed supersaturation level  $\unicode[STIX]{x1D701}$ . Once the bubble detaches, a subsequent one nucleates and the succession continues. (b) Snapshot of one of the experiments. The contour of the cylinder base surrounding the bubble can be appreciated. The position of the superhydrophobic pit from which the bubble nucleates and grows is also indicated. One clearly detects the neck joining the entrapped gas in the pit and the bubble growing outside (Moreno Soto et al. Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017).

At the beginning of the experiment, the measurement tank was pressurised with $\text{CO}_{2}$ gas at the same saturation pressure $P_{0}$ as the mixing tank. Then, by means of different valves, the solution was brought from the main tank to partially fill the experimental one. To generate bubbles, we decreased the pressure inside the latter to a value $P_{s}<P_{0}$ , and therefore, the solution became supersaturated and bubbles began to grow from the hydrophobic pit. Once a bubble had detached, a new subsequent bubble formed and the succession continued. The time between detachment and nucleation of the subsequent bubble was larger than 10 s, such that no advective flow related to the detachment and rise of the previous bubble (which is typically dissipated within 1 s) were expected to affect the growth of the subsequent one (Moreno Soto et al. Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017).

We performed different sets of experiments starting from the same saturation pressure $P_{0}\approx 9$ bars. The supersaturation level $\unicode[STIX]{x1D701}=(c_{0}-c_{s})/c_{s}$ (where $c_{0}$ and $c_{s}$ are the bulk concentration and the saturation concentration at $P_{s}$ , respectively) can be written in terms of pressure by using Henry’s law, $c=k_{H}(T)P$ , where in general $k_{H}(T)$ is a decreasing function of temperature dependent on the gas/liquid couple. By decreasing the pressure to different values of $P_{s}$ and keeping the temperature constant at all times, we achieved different values of $\unicode[STIX]{x1D701}=(P_{0}-P_{s})/P_{s}\approx 0.15,0.25$ and 0.47.

The cylinder curvature may affect the acquisition of images since the light illuminating the experiments is refracted while crossing the cylinder surface. We have made use of a ray tracer (Huisman, van Gils & Sun Reference Huisman, van Gils and Sun2012) to confirm that the refraction resulting from the light crossing the cylinder walls was inconsequential, and hence, no correction to the images needed to be applied.

As bubbles approached their detachment radius, due to the effect of buoyancy their shape started to become that of a prolate spheroid. In order to calculate a precise bubble radius, we have compared three different techniques: in the first, we fit a circle to the bubble contour; in the second, the radius was obtained by equating the measured projected area of the full bubble to that of a perfect circle; in the third, we computed the volume of the revolution body generated by rotating the bubble profile around its vertical symmetry axis. We found that, within measurement error, the three methods produced identical outcomes except for the very last moments close to bubble detachment. The variability was, however, less than 1 %, thus we could safely assume that the bubbles were perfectly spherical at all times.

3 Analysis of the growth dynamics: theoretical framework

Bubble growth in mildly supersaturated solutions is standardly associated with diffusion-driven mass transfer phenomena. In this section, we summarise results from Enríquez et al. (Reference Enríquez, Sun, Lohse, Prosperetti and van der Meer2014) and Moreno Soto et al. (Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017, Reference Moreno Soto, Enríquez, Prosperetti, Lohse and van der Meer2019), where the behaviour of single bubbles growing on a substrate immersed in a mildly supersaturated solution is described in depth. To study the behaviour of bubbles in such a configuration, two dimensionless quantities are defined:

(3.1a,b ) $$\begin{eqnarray}\displaystyle & \displaystyle \unicode[STIX]{x1D716}=\frac{R}{R_{0}},\quad x=\sqrt{\left(\frac{2D\unicode[STIX]{x1D701}c_{s}}{\unicode[STIX]{x1D70C}_{g}R_{0}^{2}}\right)t}, & \displaystyle\end{eqnarray}$$

where $R$ is the bubble radius, $R_{0}$ is a reference radius which is taken to be the radius of the pit $R_{p}$ , $D\approx 1.77\times 10^{-9}~\text{m}^{2}~\text{s}^{-1}$ is the diffusion coefficient of $\text{CO}_{2}$ in water and $\unicode[STIX]{x1D70C}_{g}$ is the gas density. Here, $\unicode[STIX]{x1D716}$ represents a dimensionless bubble radius and $x$ a dimensionless square root of time. The diffusive bubble growth is then characterised by the Epstein & Plesset (Reference Epstein and Plesset1950) equation slightly modified to account for the presence of the substrate below the bubble. The asymptotic solution then becomes

(3.2) $$\begin{eqnarray}\displaystyle & \displaystyle \unicode[STIX]{x1D716}\approx \left(\sqrt{\frac{\unicode[STIX]{x1D701}c_{s}}{2\unicode[STIX]{x03C0}\unicode[STIX]{x1D70C}_{g}}}+\sqrt{\frac{1}{2}+\frac{\unicode[STIX]{x1D701}c_{s}}{2\unicode[STIX]{x03C0}\unicode[STIX]{x1D70C}_{g}}}\right)x\equiv S^{\ast }x. & \displaystyle\end{eqnarray}$$

As one can deduce from this equation, the bubble growth is strongly dependent on the supersaturation level $\unicode[STIX]{x1D701}$ , which will be our control parameter in the experiments provided below.

From the middle stages of the bubble growth, an onset to density-driven convection takes place and enhances the mass transfer towards the bubble. Two characteristic dimensionless numbers, namely the Sherwood number $Sh$ and the Rayleigh number $Ra$ , are then defined. The former represents the dimensionless total mass transfer towards the bubble, whereas the latter relates buoyancy to viscous and diffusive effects. These two numbers can be written as (see e.g. Clift, Grace & Weber Reference Clift, Grace and Weber1978; Bejan Reference Bejan1993)

(3.3a,b ) $$\begin{eqnarray}\displaystyle & \displaystyle Sh=\frac{2\unicode[STIX]{x1D70C}_{g}R{\dot{R}}}{D(c_{0}-c_{s})},\quad Ra=\frac{g\unicode[STIX]{x1D706}_{c}(c_{0}-c_{s})(2R)^{3}}{\unicode[STIX]{x1D708}D}, & \displaystyle\end{eqnarray}$$

where $\unicode[STIX]{x1D706}_{c}$ is the concentration expansion coefficient of the $\text{CO}_{2}$ -water solution (with a typical value of ${\approx}6.6\times 10^{-4}~\text{m}^{3}~\text{kg}^{-1}$ ) and $\unicode[STIX]{x1D708}$ the kinematic viscosity. The onset of convection originates from the density decrease in the solution around the bubble as it absorbs the dissolved gas and depletes the liquid. Therefore, the parameter $\unicode[STIX]{x1D706}_{c}$ becomes very relevant since it relates the way in which a solution changes in density to the concentration of dissolved gas. In the case of $\text{CO}_{2}$ , a growing bubble may then cause a relevant decrease in the density of the surrounding liquid, which causes the formation of a buoyant depleted concentration boundary layer around the bubble and a significant enhancement of mass transfer, i.e. it promotes the transition to density-driven convection during the diffusive bubble growth. For the case of a sphere with fixed radius in steady-state (natural) convection in an infinite medium, $Sh$ and $Ra$ can be related as (see e.g. Bejan Reference Bejan1993)

(3.4) $$\begin{eqnarray}\displaystyle & \displaystyle Sh=2+KRa^{1/4}, & \displaystyle\end{eqnarray}$$

where 2 is the value of $Sh$ in the pure diffusive case and $K\approx 0.569$ is a fitting constant (Bergman et al. Reference Bergman, Incropera, DeWitt and Lavine2011; Rahman Reference Rahman2013).

For the study of the long-term depletion as the bubble succession continues within the cylinder, the depletion number is defined as

(3.5) $$\begin{eqnarray}\displaystyle & \displaystyle \unicode[STIX]{x1D6F6}_{n}=\frac{\tilde{c}_{n}-c_{s}}{c_{0}-c_{s}}, & \displaystyle\end{eqnarray}$$

where $n$ is the index indicating the bubble number within the succession and $\tilde{c}_{n}$ is the local apparent infinite concentration that the $n$ th bubble perceives due to the decreased gas concentration resulting from the previous bubble departure. It gives an estimation of how much gas is transported away by a bubble upon detachment due to the enhanced mass transfer rate towards it, which cannot be compensated by the gas diffusion through the bulk. Consequently, the local apparent concentration that subsequent bubbles experience becomes smaller and smaller. By means of this description, we redefine (3.3) to consider the effects of depletion as

(3.6a,b ) $$\begin{eqnarray}\displaystyle & \displaystyle \widetilde{Sh}=\frac{2\unicode[STIX]{x1D70C}_{g}R{\dot{R}}}{D(\tilde{c}_{n}-c_{s})}=\frac{Sh_{n}}{\unicode[STIX]{x1D6F6}_{n}},\quad \widetilde{Ra}=\frac{g\unicode[STIX]{x1D706}_{c}\left(\tilde{c}_{n}-c_{s}\right)(2R)^{3}}{\unicode[STIX]{x1D708}D}=Ra_{n}\unicode[STIX]{x1D6F6}_{n}. & \displaystyle\end{eqnarray}$$

The curves $Sh_{n}$ versus $Ra_{n}$ can then be collapsed onto one universal curve $\widetilde{Sh}=f(\widetilde{Ra})$ from which $\unicode[STIX]{x1D6F6}_{n}$ is obtained. Here, $\unicode[STIX]{x1D6F6}_{n}$ can be analytically estimated by adapting the solution of a pure diffusive problem to account for the effect of convection caused by the density difference and of the refreshing flows originating at the detachment and subsequent rise of the bubble (which has been determined to be small in comparison). We note again that the knowledge presented until now has been previously discussed in detail in previous works. The main new analysis that we present in this article is the effect of lateral confinement on a succession of bubbles.

As a bubble grows and absorbs gas from its surroundings, a concentration boundary layer develops following ${\sim}\sqrt{Dt}$ . The typical time needed for this diffusive boundary layer to occupy the full width of the cylinder can be estimated as $R_{c}^{2}/D\approx 60~\text{min}$ , whereas it takes $H^{2}/D\approx 940~\text{min}$ to cover its full length. Bearing in mind that this is a very conservative estimation and that our experiments run for ${\approx}240~\text{min}$ , we can safely presume that, in the long term, the diffusive boundary layer occupies the full width of the cylinder and can only evolve in the vertical direction towards the aperture of the confinement (which does not affect the physics studied here). It is known that this layer reaches a much longer length than the bubble radius as the succession continues (Moreno Soto et al. Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017). In that scenario, the bubble can be approximated as a plane sink which extracts gas from a certain bulk. In view of the above discussion, it is reasonable to assume that the problem becomes one-dimensional, a hypothesis which has been very recently corroborated by Rivero-Rodríguez & Scheid (Reference Rivero-Rodríguez and Scheid2019). In their work, they prove that, under regimes characterised by a very small Péclet number $Pe$ , i.e. dominated by diffusion, the concentration field far away from the bubble only evolves in the axial direction of the confinement. The discrete depletion number reads thus (for a complete derivation, refer to appendix A):

(3.7) $$\begin{eqnarray}\displaystyle \displaystyle \unicode[STIX]{x1D6F6}_{n} & = & \displaystyle \unicode[STIX]{x1D6F6}_{n-1}-\frac{4\unicode[STIX]{x1D70C}_{g}R_{det}^{3}}{3R_{c}^{2}t_{det}D(c_{0}-c_{s})}\left[2\sqrt{\frac{Dt_{det}}{\unicode[STIX]{x03C0}}}\exp \left(-\frac{\left(R_{det}+\unicode[STIX]{x1D6FC}\sqrt{3.3Dt_{det}}\right)^{2}}{4Dt_{det}}\right)\right.\nonumber\\ \displaystyle & & \displaystyle \left.-\,(R_{det}+\unicode[STIX]{x1D6FC}\sqrt{3.3Dt_{det}})\text{erfc}\left(\displaystyle \frac{R_{det}+\unicode[STIX]{x1D6FC}\sqrt{3.3Dt_{det}}}{2\sqrt{Dt_{det}}}\right)\right],\end{eqnarray}$$

where $R_{det}\approx 715~\unicode[STIX]{x03BC}\text{m}$ and $t_{det}$ are the corresponding radius (Fritz Reference Fritz1935; Og̃uz & Prosperetti Reference Og̃uz and Prosperetti1993; Moreno Soto et al. Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017) and experimentally measured time at detachment, and $\unicode[STIX]{x1D6FC}\in [0,1]$ is a fitting constant which relates to the distance within the concentration boundary layer (where 0 corresponds to the bubble interface and 1 constitutes the limit of the boundary layer) that defines the apparent bulk concentration for the subsequent bubble in the succession and, consequently, is a decreasing function of $\unicode[STIX]{x1D701}$ , i.e. bubbles deplete their surroundings faster with increasing $\unicode[STIX]{x1D701}$ (Moreno Soto et al. Reference Moreno Soto, Enríquez, Prosperetti, Lohse and van der Meer2019). Whereas $R_{det}$ is a parameter which is determined by a force balance and remains almost constant throughout our experiments, the measurement of the detachment time $t_{det}$ and $\unicode[STIX]{x1D6FC}$ incorporates convective effects as the bubble grows. Indeed, $t_{det}$ increases for subsequent bubbles as the effect of depletion becomes more significant. Note that (3.7) differs slightly from the expression provided in Moreno Soto et al. (Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017), where a spherically symmetric three-dimensional situation was modelled, and that the concentration gradient referred to in the following corresponds to the one measured in the longitudinal axis of the cylinder. Towards the lowest limit in which $R_{c}=R_{det}$ , the model in (3.7) is expected to become increasingly precise, since the assumption of a one-dimensional scenario becomes valid at progressively earlier times as $R_{c}$ approaches $R_{\text{det}}$ . This could unfortunately not be tested experimentally due to the limitations of our set-up. In addition, the confinement is not expected to play a significant role when $R_{c}\gg R_{det}$ and the problem can be solved as in Moreno Soto et al. (Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017).

4 Effect of the supersaturation level $\unicode[STIX]{x1D701}$ in confined bubble growth

In § 3, we discussed that the supersaturation level $\unicode[STIX]{x1D701}$ determines the speed at which bubbles grow, as one can see from the definitions of $x$ and $S^{\ast }$ in (3.2). The higher its value, the faster it is expected that bubbles grow. We present the growth of different successive bubbles in confinement in figure 2(a). The bubble growth behaves as expected: higher supersaturation levels correspond to an increased bubble growth rate. The cases of $\unicode[STIX]{x1D701}=0.15,0.25$ show very similar behaviour when plotted in their dimensionless form. Nonetheless, since $x\propto \unicode[STIX]{x1D701}^{1/2}$ , the unscaled data for smaller $\unicode[STIX]{x1D701}$ lie below those of larger $\unicode[STIX]{x1D701}$ , as reflected in the inset of the same figure.

Figure 2.

(a) Dimensionless radius $\unicode[STIX]{x1D716}$ plotted against the dimensionless square root of time $x$ for subsequent bubbles in confinement. The different colours represent different supersaturation levels $\unicode[STIX]{x1D701}$ , namely, blue for 0.15, red for 0.25 and yellow for 0.47. The different symbols stand for the order of the bubble in the succession, namely circles for the first bubble and diamonds for the fifth, whereas (3.2) is plotted as solid lines in the corresponding colours. The inset shows the unscaled data for the time evolution of the bubble radius $R$ prior to the non-dimensionalisation. (b) Derivative of the dimensionless radius versus the dimensionless square root of time. The same colour symbol coding as in panel (a) applies here. Equation (3.2) coincides for the three different $\unicode[STIX]{x1D701}$ and is represented as a black solid line. Note that increasing $\unicode[STIX]{x1D701}$ causes an earlier and intensified onset of convection.

Depletion effects are expected to be strengthened by increasing the supersaturation level. The onset of density-driven convection permits the bubbles to absorb more gas than diffusion can supply from far away in the bulk solution, and specifically for the geometrical configuration regarded in this article (figure 1), the cylinder walls also play a crucial role in inhibiting the refreshment with non-depleted bulk liquid. In figure 2(b), we show the derivatives of the curves in figure 2(a) with respect to the dimensionless square root of time $x$ . As the supersaturation increases, we can appreciate that the onset occurs earlier and is intensified, as indicated by a higher transient peak and a shorter plateau before the slope. We remind the reader that $x\propto \sqrt{\unicode[STIX]{x1D701}t}$ in such a way that, even if the onset of convection seems to occur at a relative similar $x$ , the absolute time is actually shorter for larger $\unicode[STIX]{x1D701}$ . Figure 3(a) represents the diverse values of $Sh$ plotted against $Ra$ for the different curves in figure 2. By comparing the experimental data to the theoretical relation (3.4) (which, as expected, lies above the experimental curves as it corresponds to a free bubble in an infinite medium), we distinguish a short early behaviour where $Sh$ remains constant and indicates an early diffusive regime, and a transition to convection from the middle stages of the bubble growth, which has been also confirmed for the analogous case of droplets (Dietrich et al. Reference Dietrich, Wildeman, Visser, Hofhuis, Kooij, Zandvliet and Lohse2016). The experimental curves are parallel to the theoretical one in the sense that was introduced in Moreno Soto et al. (Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017), where it was shown that they collapse onto the same universal curve when they are rescaled using the depletion parameter $\unicode[STIX]{x1D6F6}$ defined in (3.6), as we discussed in § 3.

Figure 3.

(a) Sherwood number $Sh$ against Rayleigh number $Ra$ for the same bubbles as in figure 2 plotted in logarithmic scale. Depletion can already be appreciated for the fifth bubble, which is clearly separated from the first curve. To compare, the theoretical relation for natural convection around bubbles in an infinite medium, equation (3.4), is shown. The experimental curves lie below but ‘parallel’ (see main text) to the theoretical expression, indicating that, indeed, natural convection is driving the bubble growth from the middle stages of its growth onwards. (b) The depletion number $\unicode[STIX]{x1D6F6}$ decreases for increasing $\unicode[STIX]{x1D701}$ , as expected from an enhanced bubble growth rate. The solid lines represent the best theoretical approximation for each $\unicode[STIX]{x1D701}$ according to (3.7).

Regarding the long-term depletion effect, the different curves standing for the analytical solution (3.7) can be found in figure 3(b), together with the experimental results measured from collapsing the curves in figure 3(a). Similarly to the case of bubbles growing on an unconfined surface (Moreno Soto et al. Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017), $\unicode[STIX]{x1D6F6}_{n}$ decreases for every subsequent bubble in the succession and, for the different curves, an increase in $\unicode[STIX]{x1D701}$ implies a stronger depletion, i.e. $\unicode[STIX]{x1D6F6}$ decreases faster for higher $\unicode[STIX]{x1D701}$ . The experiments are well described with the theoretical expression (3.7), with fitting constant $\unicode[STIX]{x1D6FC}=0.57,0.53$ and $0.45$ for $\unicode[STIX]{x1D701}=0.15,0.25$ and 0.47, respectively. The expected decreasing value of $\unicode[STIX]{x1D6FC}$ with increasing $\unicode[STIX]{x1D701}$ is also confirmed in the case of confinement. Note that $\unicode[STIX]{x1D6F6}$ decreases faster in time for higher $\unicode[STIX]{x1D701}$ , but if we compare $\unicode[STIX]{x1D6F6}$ for the same bubble number $n$ , its value is bigger for larger $\unicode[STIX]{x1D701}$ . This is due to the longer times bubble need to grow until detachment for a smaller supersaturation. Therefore, convection has more time to develop such that gas diffusion from the non-depleted bulk cannot efficiently compensate for the absorbed gas, even though the onset of density-driven convection may be weaker as compared to higher supersaturated scenarios. The slight deviation between experiments and the theoretical fit may be connected to the one-dimensional (1-D) approximation. Moreover, the model seems to have difficulties capturing the behaviour of the first few bubbles in the succession. This also occurs for the experiments to be presented in the following section. For these first bubbles, the growing depleted concentration boundary layer has probably not yet reached the confinement walls and, therefore, the 1-D assumption is not yet applicable. We have indicated before that it takes up to ${\approx}60~\text{min}$ for the concentration boundary layer to cover the full width of the cylinder. It is from that moment on that the 1-D model (3.7) is expected to capture the details of the effect of long-term depletion. As a closing remark, we stress that the three-dimensional (3-D) model in Moreno Soto et al. (Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017) does not compare well to the experimental data presented in figure 3(b) for any value of $\unicode[STIX]{x1D6FC}$ . This supports the necessity of introducing a 1-D model to accurately describe the bubble behaviour in confinement.

To summarise this section, $\unicode[STIX]{x1D701}$ has been proven to be the adequate control parameter which determines the speed at which bubbles grow, as well as an indicator of the speed and the intensity of depletion. The case is analogous to bubbles growing in a unbounded domain on a surface (Moreno Soto et al. Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017, Reference Moreno Soto, Enríquez, Prosperetti, Lohse and van der Meer2019).

5 Comparison of confined and unconfined bubble growth

In this section we focus on the actual effect of the confinement by comparing with experiments in which the bubbles grow on a surface in an (for practical purposes) infinite medium. We discuss two sets of $\unicode[STIX]{x1D701}$ independently, since, contrary to expectations, we will see that depletion evolves in a qualitatively different manner for each case.

5.1 Supersaturation level $\unicode[STIX]{x1D701}=0.15$

Figure 4.

(a) Dimensionless radius $\unicode[STIX]{x1D716}$ plotted against the dimensionless square root of time $x$ for experiments with $\unicode[STIX]{x1D701}=0.15$ . In blue, the bubbles grow under confinement, whereas in red, the bubbles grow in an open medium. Different symbols are used to indicate the first (circle), fifth (diamond) and tenth (star) bubbles in the succession. The curves within the same succession deviate from each other due to the effect of depletion. (b) Derivative of the dimensionless radius versus the dimensionless square root of time. The effects of depletion are very noticeable in this data representation. The respective curves with and without confinement seem to run parallel, indicating a similar strength in the onset of convection. In (a,b), the solid line corresponds to (3.2).

The very low supersaturation level $\unicode[STIX]{x1D701}=0.15$ corresponds to an extremely slow growth rate, approximately $20$ min for the first bubbles. Figure 4(a) shows the dimensionless bubble radius evolution in dimensionless square root of time in confinement compared to the same in the unconfined case. The beginning of the bubble growth in both scenarios is very similar: bubbles grow according to the theoretical curve (3.2). However, and contrary to expectations, the bubbles under confinement seem to grow slightly faster than the bubbles in the open medium. This fact can be better appreciated in figure 4(b), where the derivatives show that the curves corresponding to the bubbles under confinement lie somewhat above those for the open medium. The transition to convection occurs slightly earlier for confined bubbles and consequently bubbles grow to some degree faster than those on an unconfined surface. This may originate from the local larger concentration gradients within the confined system, which would create a larger buoyant force on a smaller volume.

The depletion effects can be appreciated in figure 6(a), where $\unicode[STIX]{x1D6F6}_{n}$ is plotted versus time. For a small supersaturation, depletion occurs faster in the confined case as a result of the rather enhanced bubble growth and the shielding effect of the walls for renewing the depleted liquid with fresh non-depleted solution once a bubble detaches. In the confined case, the mixing that occurs at detachment happens for this small supersaturation in a large boundary layer with a small concentration gradient, and therefore, its effect is less pronounced as compared to the supply of fresh, non-depleted solution in the unconfined scenario. In figure 6(a) we plot the theoretical model (3.7) for the confined and the one by Moreno Soto et al. (Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017) for the unconfined case together with the corresponding experimental measurements, showing a good agreement for both models. Both the theoretical curves and the experiments show a very similar behaviour for the first few bubbles in the succession. This can be associated with the growth of the boundary layer, which for the confined case does not reach the walls of the cylinder until later in the succession. From that moment on, the curves start to diverge and hence, in the long term, depletion is slightly stronger in confinement than in the open system, as one would expect.

5.2 Supersaturation levels $\unicode[STIX]{x1D701}=0.25$ and $0.47$

Figure 5.

(a) Evolution of the dimensionless radius $\unicode[STIX]{x1D716}$ for $\unicode[STIX]{x1D701}=0.47$ and (b) corresponding derivative versus the dimensionless square root of time $x$ . The solid lines correspond to (3.2). There has been an inversion of some of the behaviour observed for $\unicode[STIX]{x1D701}=0.15$ (figure 4): now, the first confined bubble grows slower than that in the unconfined case. However, due to a stronger depletion for the unbounded bubble, the subsequent bubbles in confinement grow faster.

Once the supersaturation $\unicode[STIX]{x1D701}$ increases, confinement starts playing a major role on the way bubbles grow from the hydrophobic pit. Similarly to the previous subsection, figure 5(a) shows the dimensionless radius $\unicode[STIX]{x1D716}$ evolution for $\unicode[STIX]{x1D701}=0.47$ (for $\unicode[STIX]{x1D701}=0.25$ , the bubble behaviour is qualitatively the same). Now, this case shows a faster growth for the first bubbles in the unbounded case than for the confined case, contrary to what happened in the previous subsection with $\unicode[STIX]{x1D701}=0.15$ . It is particularly interesting to notice that successive bubbles in confinement grow according to (3.2) until convection sets in, whereas for the unconfined case, only the very first bubbles in the succession match the analytical behaviour at the very early stages. This is due to the strong onset of convection and consequent depletion which occurs at supersaturations $\unicode[STIX]{x1D701}<1{-}2$ achieved from a very high initial pressure $P_{0}$ (Moreno Soto et al. Reference Moreno Soto, Enríquez, Prosperetti, Lohse and van der Meer2019). The higher $\unicode[STIX]{x1D701}$ , the faster and the stronger this onset occurs, as can be determined from figure 5(b). This transition appears to be inhibited in the confined case, such that convection sets in later in time and without such a strength.

Consequently, figures 6(b) and 6(c) show that bubbles in an unbounded domain deplete much faster than bubbles in confinement, represented by a faster decreasing $\unicode[STIX]{x1D6F6}_{n}$ . One could expect the opposite nonetheless, since the confinement impedes the dissolved gas in the bulk diffusing towards the bubble and compensating for the absorbed gas, which indeed happens in the case of bubbles growing in an open medium. The explanation of this enhanced depletion in the open system resides in the mechanism from which it originates: a full buoyant depleted volume is formed as bubbles absorb gas from their surroundings, which induces a stronger and intensified transition to natural convection. Note that the mass transfer enhancement is referred to the specific bubble diffusive growth and, therefore, the total mass transfer towards a bubble is always being reduced within the succession, equivalently to what occurs in figure 3(a). Consequently, bubbles progressively deviate more from the theoretical growth curve, equation (3.2), as the succession continues. That depleted volume rises together with the bubble after detachment and partially replaces the depleted solution with fresh liquid from the bulk (Moreno Soto et al. Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017). In bounded domains, these phenomena occur differently, since the confining walls firstly impede the formation of a buoyant depleted domain and, secondly, favour the gas mixing within the depleted area. These two effects combined result in a weaker long-term depletion. We note that convection has a slight effect on the final detachment radius (Enríquez et al. Reference Enríquez, Hummelink, Bruggert, Lohse, Prosperetti, van der Meer and Sun2013), which also applies to the results in the previous section § 5.1. We have measured the ratio between the bubble radius at detachment for the confined and unconfined cases to be always larger than 0.9. However, this small difference can signify up to 10 min of additional growth time to achieve detachment. The accumulation of this time mismatch together with the larger depletion in the unconfined case continuously enlarge the lifetime of the bubbles, i.e. the bubble frequency decreases. Hence, figure 6 shows always a higher bubble frequency for the confined case, which is more noticeable for higher $\unicode[STIX]{x1D701}$ .

For time scales beyond the duration of our experiments, we anticipate that the impediment of solution refreshment due to the presence of the walls may start playing a dominant role and, therefore, the confined succession will start depleting faster as compared to the unbounded domain, as the cross-over by extrapolating the curves in figures 6(b) and 6(c) appears to suggest.

Figure 6.

(a) The evolution of the depletion number $\unicode[STIX]{x1D6F6}_{n}$ as a function of time for $\unicode[STIX]{x1D701}=0.15$ shows that for the first five bubbles in the succession, bubbles in the confined and open cases deplete their surroundings in very similarly manner. In the long term, depletion is more affected by the minute stronger convective effect occurring in confinement. The solid lines in the corresponding colours represent the theoretical behaviour indicated by (3.7) for the confined domain (blue) and the model by Moreno Soto et al. (Reference Moreno Soto, Prosperetti, Lohse and van der Meer2017) for the non-confined (red). (b,c) The depletion number $\unicode[STIX]{x1D6F6}_{n}$ for (b)  $\unicode[STIX]{x1D701}=0.25$ and (c) $\unicode[STIX]{x1D701}=0.47$ strongly decreases for the unconfined scenario as compared to the bounded domain due to the full development of the buoyant depleted boundary layer. Increasing $\unicode[STIX]{x1D701}$ provides the same qualitative behaviour. Note that for all the cases, the bubble frequency for the confined case is always larger than for the unconfined case. This originates from the accumulation of time mismatch due to the slight difference in the final $R_{det}$ and the different ways in which the buoyant depleted boundary layer develops in the two cases.