Hostname: page-component-7b7567c8c-z4zkx Total loading time: 0 Render date: 2026-11-18T01:40:19.054Z Has data issue: false hasContentIssue false

Modelling the decay of finite-span starting and stopping wall jets in an external stream

Published online by Cambridge University Press:  08 November 2022

Ben Steinfurth*
Affiliation:
Institute of Aeronautics and Astronautics, Technische Universität Berlin, Marchstr. 12–14, 10587 Berlin, Germany
Julien Weiss
Affiliation:
Institute of Aeronautics and Astronautics, Technische Universität Berlin, Marchstr. 12–14, 10587 Berlin, Germany
*
†Email address for correspondence: ben.steinfurth@tu-berlin.de

Abstract

The flow under consideration is a wall jet that results from an inclined jet in cross-flow emitted into a zero-pressure-gradient turbulent boundary layer from a slot-like outlet of width $b=0.5\,\mathrm {mm}$ and span $L=20\,\mathrm {mm}$. Despite the finite jet span, the velocity decay and wall-normal spreading rate in the symmetry plane can be described with power laws almost identical to those for the two-dimensional flow determined by Zhou & Wygnanski (AIAA J., vol. 31, 1993, pp. 848–853). This is explained by the lack of significant lateral spreading found in the present configuration due to a self-amplifying inward-directed fluid motion, fundamentally differing from conditions found in the absence of an external stream. Regions with ‘approximately self-similar’ properties also exist in the case of unsteady velocity programmes where the fluid is ejected in a pulsatile fashion. Here, the wall jet is enclosed by a leading vortex structure and a deceleration wave, for which the time-dependent locations can be predicted by means of empirical constants. This yields models for the major properties inside the advancing and diffusing wall jet that only require knowledge regarding the velocity ratio, the ejected momentum flux and the kinematic viscosity, representing an extension to scaling laws for steady wall jets in still ambience established by Narasimha et al. (Aeronaut. Q., vol. 77, 1973, pp. 355–359).

Information

Type
JFM Papers
Copyright
© The Author(s), 2022. Published by Cambridge University Press
Figure 0

Figure 1.Experimental set-up and sketch of wall jet velocity profile.

Figure 1

Figure 2.Idealised velocity programmes for investigated wall jet configurations.

Figure 2

Figure 3.Gain in streamwise velocity due to steady wall jets of different velocity ratios (a) and mean spanwise vorticity fields (b).

Figure 3

Figure 4.Steady wall jet velocity profiles with scaling suggested by ZW93: $\circ$, $R=0.5$; $\square$, $R=0.67$; $\diamond$, $R=0.75$; dash-dotted curve, data by ZW93.

Figure 4

Figure 5.Scaled steady wall jet properties for the range $x/b = 50,\ldots,570$. The ${\pm }5\,\%$ interval of power-law fit is highlighted by the shaded area; for scaled wall shear stress data ($F_2$), the shaded area represents estimations based on correlation by Bradshaw & Gee (1962). The dash-dotted line represents data by ZW93.

Figure 5

Figure 6.Mean velocity fields in cross-sections at $x/b=100$ (a,b), $x/b=300$ (c,d) and $x/b=600$ (e,f). (a,c,e) Co-flow with mean inflow velocity $U_\infty = 20\,{\rm m}\,{\rm s}^{-1}$ ($R=0.67$) and (b,d,f) no co-flow ($U_\infty = 0\,{\rm m}\,{\rm s}^{-1}$). Jet half-width indicated by white line.

Figure 6

Figure 7.Profiles of spanwise velocity component $w$ at $x/b=600$ in $z/b>0$ half-plane at the location of maximum $w$: (a) $U_\infty = 20\,{\rm m}\,{\rm s}^{-1}$ and (b) zero co-flow ($U_\infty = 0\,{\rm m}\,{\rm s}^{-1}$). The sign of streamwise vorticity amplification through vortex-line bending is highlighted for inner and outer layers of wall jets.

Figure 7

Figure 8.Time series of gain in streamwise velocity due to $R=0.67$ starting wall jets (a) and mean spanwise vorticity (b).

Figure 8

Figure 9.(a) Time series of FTLE fields for $R=0.67$ starting wall jet. (b) Peak jet velocities with respective wall distance for the same time steps as in (a). The dashed verticals highlight the time-dependent boundary between wall jet and leading vortex indicated by the departure of $Y_m$ from the curve for the steady wall jet.

Figure 9

Figure 10.Time-dependent locations of boundary between leading vortex and starting wall jet for different velocity ratios. Linear fits are highlighted by dashed lines. (a) Locations as a function of time and (b) locations scaled with $R$.

Figure 10

Figure 11.Scaled starting wall jet properties for different time instants. Black symbols are used for the region upstream of leading vortex and grey symbols for the region further downstream.

Figure 11

Figure 12.Time series of gain in streamwise velocity due to $R=0.67$ stopping wall jet (a) and mean spanwise vorticity (b).

Figure 12

Figure 13.(a) Peak jet velocities $U_m$ and (b) respective wall distance $Y_m$ for $R=0.67$ stopping wall jet for different time steps subsequent to the termination of fluid emission at $t=t_p$.

Figure 13

Figure 14.Time-dependent locations of deceleration wave for stopping wall jets of different velocity ratios. Linear fits are highlighted by dashed lines. (a) Locations as a function of time and (b) locations scaled with $R$.

Figure 14

Figure 15.Scaled stopping wall jet properties for different time instants. Black symbols are used for the region downstream of deceleration wave and grey for deceleration wave and unforced boundary layer upstream of the wall jet.

Figure 15

Figure 16.Comparison between measurement data (black curves) and modelled jet properties (red curves) for pulsed wall jet with duration $t_{p}=11\,\mathrm {ms}$. (a–c) Velocity distributions for $R=(0.5, 0.67, 0.75)$. (d–f) Locations of maximum velocity for $R=0.67$.

Figure 16

Figure 17.Measured wall shear stress signals (black curves) and modelled wall shear stress (red curves) for pulsed wall jet with duration $t_{p}=11\,\mathrm {ms}$ at five locations downstream of jet outlet.

Steinfurth and Weiss supplementary movie 1

Visualisation of the extraction of time-dependent propagation front location $x_p/b$; upper diagram: FTLE field with $x_p/b$ marked by red dashed vertical line, lower diagram: jet spreading rates for steady and starting wall jets with $x_p/b$ marked by red circle
Download Steinfurth and Weiss supplementary movie 1(Video)
Video 1.7 MB

Steinfurth and Weiss supplementary movie 2

Visualisation of the extraction of time-dependent deceleration wave location $x_d/b$; upper diagram: FTLE field with $x_d/b$ marked by red dashed vertical line, lower diagram: maximum jet velocities for steady and starting wall jets with $x_d/b$ marked by red circle

Download Steinfurth and Weiss supplementary movie 2(Video)
Video 759.5 KB