2.1. Method to produce a centred compression wave

The centred compression wave is here generated from the lower wedge surface, which has a continuously increasing deflection angle, represented in figure 2(b) by a finite number of Mach waves for clarity.

Let $\theta _{w}$ be the accumulated deflection angle of the lower wedge surface to produce the compression waves. The lower surface producing the centred compression wave can be viewed as having an infinite number of turning or deflection, each with a deflection angle $\Delta \theta _{w}\rightarrow 0$. To define the wedge lower surface shape that produces the required centred compression wave, we adopt a coordinate system with the horizontal axis coinciding with the reflecting surface and the vertical axis passing through the leading edge $A_{1}$ of the wedge.

By centred compression wave reflection we mean all the Mach waves will intersect at a common point $N$ on the reflecting surface, as shown in figure 2(b). The Mach waves all converge to a single point (say $N$) if the coordinates of the wedge lower surface $(x,y)$ satisfy

(2.1)\begin{equation} \tan (\theta +\mu )=\frac{y}{x_{N}-x}, \end{equation}

where $\theta$, with $\tan \theta =-({{\rm d}y}/{{\rm d}\kern0.7pt x})$, is the local wedge angle compared with the horizontal axis (positive if downward) and $\mu =\arcsin ({1}/{M})$ is the Mach angle.

The shape given by (2.1) can also be written more explicitly as

(2.2)\begin{equation} \tan \left(\arcsin \frac{1}{M}-\arcsin \frac{{\rm d}y}{{\rm d}\kern0.7pt x}\right) =\frac{y}{ x_{N}-x}, \end{equation}

where the Mach number $M$ is determined by the Mach wave relation $\nu ( M) -\nu ( M_{0}) =-\theta$, or

(2.3)\begin{equation} \nu (M) -\nu (M_{0}) =\arctan \left(\frac{{\rm d}y}{{\rm d}\kern0.7pt x}\right). \end{equation}

Numerically, the centred compression wave may be represented by a finite number, say $K$, of discrete Mach waves $L_{k}$ with $k=1,2,\ldots,K$, each being produced due to a small wedge deflection ($\Delta \theta _{w}=\theta _{w}/K$) at points $A_{k}$ with $k=1,2,\ldots,K$, as shown in figure 2(b) where only five Mach waves are shown for clarity.

The wedge deflection angle at each discrete point $A_{k}$, compared with the inflow direction, is $\theta _{A_{k}}=k\Delta \theta _{w}$ with $k=1,2,\ldots,K$.

The vertical position $y_{A_{k}}$ at each turning point satisfies the following obvious geometrical relation:

(2.4) \begin{equation} \left\{\begin{array}{@{}l} y_{A_{k}}-y_{A_{k+1}}=(x_{A_{k+1}}-x_{A_{k}}) \tan (k\Delta \theta _{w}),\quad k=1,2,\ldots,K-1, \\ y_{A_{k}}-y_{R}=(x_{R}-x_{A_{k}}) \tan (k\Delta \theta_{w}),\quad k=K. \end{array}\right. \end{equation}

Here $y_{A_{1}}=H_{A_{1}}=H_{A}$ and $H_{A}$ denotes the inlet height.

A Mach wave $L_{k}$ of Mach angle $\mu _{A_{k}}=\arcsin ({1}/{M_{k-1}})$ is produced at $A_{k},$ where $M_{k-1}$ is the Mach number just upstream of the Mach wave generated at $A_{k}$. The Mach number $M_{k}$ is related to the flow deflection angle $\theta _{A_{k}}=k\Delta \theta _{w}$ by the Prandtl–Meyer wave relation applied to the present centred compression wave

(2.5)\begin{equation} \nu (M_{k}) -\nu (M_{0}) ={-}\theta _{A_{k}}, \end{equation}

where $\nu ( M)$ is the well-known Prandtl–Meyer function defined by

(2.6)\begin{equation} \nu (M) =\sqrt{\frac{\gamma +1}{\gamma -1}}\arctan \sqrt{\frac{ \gamma -1}{\gamma +1}(M^{2}-1)}-\arctan \sqrt{M^{2}-1}. \end{equation}

Alternatively, we may also use the differential form of the Mach wave relation

(2.7)\begin{equation} \frac{{\rm d} M}{M}={-}\frac{\left(1+\dfrac{\gamma -1}{2}M^{2}\right){\rm d}\theta } {\sqrt{M^{2}-1}}, \end{equation}

which, after integration, also gives (2.5).

For a centred compression wave, each Mach wave is required to reflect at a common point, here denoted $N(x_{N},0)$, on the reflecting surface, which imposes the following constraint for the horizontal position $x_{A_{k}}$ of $A_{k}$:

(2.8) \begin{equation} \left\{\begin{array}{@{}l} x_{A_{1}}=0, \\ x_{N}-x_{A_{k+1}}=\dfrac{y_{A_{k+1}}}{\tan (\mu _{A_{k+1}}+k\Delta \theta _{w})},\quad k=1,2,\ldots,K-1. \end{array}\right. \end{equation}

Here $x_{N}$, common to all Mach waves, is determined by that of the leading characteristics, i.e.

(2.9)\begin{equation} x_{N}=\frac{y_{A_{1}}}{\tan \mu _{A_{1}}}=\frac{H_{A}}{\tan \mu _{A_{1}}}. \end{equation}

Knowing $x_{A_{1}}=0,$ $y_{A_{1}}=H_{A}$, and given $y_{R}$, the expressions (2.4) and (2.8) can be used to find $x_{A_{2}}$ and $y_{A_{2}}$. More generally, the expressions (2.4) and (2.8) can be solved to give

(2.10) \begin{equation} \left\{\begin{array}{@{}l} x_{A_{k+1}}=\dfrac{y_{A_{k}}+x_{A_{k}}\tan (k\Delta \theta_{w}) -x_{N}\tan (\mu _{A_{k+1}}+k\Delta \theta _{w})}{\tan (k\Delta \theta _{w}) -\tan (\mu _{A_{k+1}}+k\Delta \theta _{w})}, \\ y_{A_{k+1}}=(x_{N}-x_{A_{k+1}}) \tan (\mu_{A_{k+1}}+k\Delta \theta _{w}), \end{array}\right. \end{equation}

so that $x_{A_{k+1}}$ and $y_{A_{k+1}}$ are explicitly related to $x_{A_{k}}$ and $y_{A_{k}}$.

There will be a limit of the allowable deflection angle $\theta _{w}$, and this limit occurs when the last point $A_{K}$ coincides with the trailing edge $R$. This restriction will be considered in § 4.2.

2.2. Numerical evidence of regular and Mach reflection for centred compression wave

Here we use numerical simulation to demonstrate the existence of both regular reflection and Mach reflection. In the meantime we perform a grid convergence study. A regular reflection and a Mach reflection for centred compression wave reflection are displayed in figure 3(a,b), respectively.

Figure 3.

Mach number contours for centred compression wave reflection with $M_{0}=4$. (a) Regular reflection ($\theta _{w}=18^{\circ }$, $y_{R}/y_{A_{1}}=0.45$); (b) Mach reflection ($\theta _{w}=30^{\circ }$, $y_{R}/y_{A_{1}}=0.4$).

It is seen that, for regular reflection, there is a single reflected shock, similar to regular reflection of shock reflection. Mach reflection is largely different to that of shock reflection; see § 4.1 for discussions.

We have found that a large number of grids is required to resolve the centred compression wave and the reflected shock wave. To see this, we perform a grid refinement study. When the grid is refined, the wedge lower surface is also refined, in such way that the lower surface satisfies the shape function (2.1) if the grid size vanishes.

Figure 4 shows, for $M_{0}=4$ and $\theta _{w}=30^{\circ }$, the Mach number contours using four different grids of increasing density. Mesh C, which has $2000\times 400$ grid points, produces results very close to those using the denser mesh D. The influence of grid density on the Mach stem height $H_{T}$ is shown in table 1. The Mach stem height $H_{T}$ is defined as the height of the intersection point between the Mach stem and the leading characteristics of the centred compression wave. The Mach stem height varies less than $1.4\times 10^{-3}$ if we replace mesh D with mesh C, so we will use a mesh as dense as mesh C in the following computations.

Figure 4.

Mach number contours for $M_{0}=4$, $\theta _{w}=30^{\circ }$ with different meshes. (a) Mesh A, $500\times 100$; (b) mesh B, $1000\times 200$; (c) mesh C, $2000\times 400$; (d) mesh D, $3000\times 600$.

Table 1.

Mach stem height for different meshes at $M_{0}=4$ and $\theta _{w}=30^{\circ }$.

3.1. Transition conditions

Given $M_{0}$ and the total wedge deflection angle $\theta _{w}$, the flow parameters in region (1) of figure 2(b) downstream of the centred compression wave are simply given by the isentropic wave relations

(3.1)\begin{equation} \left\{\begin{array}{@{}c} \nu (M_{1}) -\nu (M_{0}) ={-}\theta _{w}, \\ p_{1}=p_{0}{\left(\dfrac{1+\dfrac{\gamma -1}{2}M_{0}^{2}}{1+ \dfrac{\gamma -1}{2 }M_{1}^{2}}\right)}^{{\gamma }/{(\gamma -1)}}, \end{array}\right. \end{equation}

where $\nu ( M)$ is the Prandtl–Meyer function defined by (2.6).

In case of regular reflection, the flow parameters in the region downstream of the reflected shock, denoted region (2) of figure 2(b), is now given by the oblique shock wave relation with flow deflection angle $\theta _{w}$,

(3.2) \begin{equation} \left\{\begin{array}{@{}c} \tan \theta _{w}=f_{\theta }(M_{1},\beta _{12}), \\ M_{2}=f_{M}(M_{1},\beta _{12}), \\ p_{2}=p_{1}f_{p}(M_{1},\beta _{12}), \end{array}\right. \end{equation}

where

(3.3) \begin{equation} \left\{\begin{array}{@{}l} f_{\theta }({M,\beta })=\dfrac{2({M}^{2}{\sin }^{2}{\beta }-1)}{({M}^{2} (\gamma +\cos {2\beta }) +2) \tan {\beta }}, \\ f_{M}(M,{\beta )}=\sqrt{\dfrac{(\gamma -1) {M}^{2}+2}{2\gamma {M}^{2}{\sin }^{2} {\beta }- (\gamma -1)}+\dfrac{2{M}^{2}{\cos }^{2}{ \beta }}{(\gamma -1) {M}^{2}{\sin }^{2} {\beta }+2}}, \\ f_{p}(M,{\beta )}=1+\dfrac{2\gamma }{\gamma +1}({M}^{2}{\sin }^{2}{ \beta }-1). \end{array}\right. \end{equation}

The detachment condition, denoted as $\theta _{w}=\theta _{w}^{(D)}(M_{0})$, is the value of $\theta _{w}$ such that the reflected shock reaches the detachment condition, i.e.

(3.4)\begin{equation} \tan \theta _{w}^{(D)}(M_{0})=\frac{2[(M_{1}^{2}-1)\tan ^{2} \beta_{m}-1]}{\tan \beta _{m}[(\gamma M_{1}^{2}+2)(1+\tan ^{2} \beta _{m})+M_{1}(1-\tan ^{2}\beta _{m})]}, \end{equation}

where $\beta _{m}$, given by

(3.5)\begin{equation} \sin ^{2}\beta _{m}=\frac{1}{\gamma M_{1}^{2}}\left[\frac{\gamma +1}{4} M_{1}^{2}-1+\sqrt{(1+\gamma )\left(1+\frac{\gamma -1}{2}M_{1}^{2}+\frac{\gamma +1 }{16}M_{1}^{4}\right)}\right], \end{equation}

is the shock angle $\beta$ at which ${{\rm d}\theta }/{{\rm d}\beta }$ vanishes.

The von Neumann condition is the condition for $\theta _{w}$, denoted as $\theta _{w}=\theta _{w}^{(N)}(M_{0})$, such that the pressure $p_{2}$ determined by (3.2) is equal to the pressure $p_{N}$ of a normal shock wave connecting to region $(0)$, i.e.

(3.6)\begin{equation} p_{2}=p_{N}=p_{0}\,f_{p}\left(M_{0},\frac{\rm \pi}{2}\right) \end{equation}

The transition criteria in the $M_{0}-\theta _{w}$ are displayed in figure 5, where we also show the transition criteria for conventional shock reflection. We observe that the von Neumann condition for centred compression wave reflection is lower than that for shock reflection, and, in contrast, the detachment condition for centred compression wave reflection is higher than that for shock reflection. Thus, the double solution domain for the centred compression wave reflection is larger than that for shock reflection.

Figure 5.

Transition criteria, in the $M_{0}-\theta _{w}$ plan, for centred compression wave (CCW) reflection, compared with the transition criteria for shock wave reflection.

The observed difference between centred compression wave reflection and shock reflection can be heuristically understood. It is well known that to achieve the same flow deflection angle, isentropic Mach wave compression gives a larger pressure jump and a smaller Mach number decrease than shock compression, meaning that region (1) has a higher pressure and higher Mach number with centred compression wave reflection than that with a shock reflection. Thus, centred compression wave reflection has the same effect on reflection than shock reflection with a larger $\theta _{w}$. As a result, the transition curves for centred compression wave reflection could be seen as a shift to the left and compression of the transition curves for shock wave reflection, thus enlarging the double solution domain at the same abscissa.

The difference between centred compression wave reflection and shock reflection can also be explained using shock polars. Figure 6(a,b) gives the shock polars for $\theta _{w}=20^{\circ }$ and $\theta _{w}=27^{\circ }$, both with $M_{0}=4$.

Figure 6.

Shock polars for centred compression wave (CCW) reflection, with $M_{0}=4$. Results are shown for (a) $\theta _{w}=20^{\circ }$ and (b) $\theta _{w}=27^{\circ }$. RR - Regular reflection; MR - Mach reflection.

At $\theta _{w}=20^{\circ }$, shock polars for shock reflection, marked with dashed lines, only permit regular reflection. The polar representing the reflected shock wave may intersect the axis (regular reflection) but not the strong part (upper branch) of the polar from the origin. Shock polars for centred compression wave reflection, marked with solid lines, however, allow both regular reflection and Mach reflection. According to figure 5, the condition with $M_{0}=4$ and $\theta _{w}=20^{\circ }$ lies at the regular reflection domain for shock reflection and the double solution domain for centred compression wave reflection.

At $\theta _{w}=27^{\circ }$, shock polars for shock reflection, marked with dashed lines, only permit Mach reflection. The polar representing the reflected shock wave can not intersect the axis but can intersect the strong part (upper branch) of the polar from the origin. Shock polars for centred compression wave reflection, marked with solid lines, however, allow both regular reflection and Mach reflection. According to figure 5, the condition with $M_{0}=4$ and $\theta _{w}=27^{\circ }$ lies at the Mach reflection domain for shock reflection and the double solution domain for centred compression wave reflection.

In the following we use numerical simulation to verify the conclusion from transition analysis.

3.2. Numerical verification of transition conditions

Numerical simulation is carried out for $M_{0}=4$ with a series of wedge deflection angles $\theta _{w}$, which span the Mach reflection region, double solution region and regular reflection region shown in figure 5 for both centred compression wave reflection and shock wave reflection. In case it is possible to have a double solution, there are various ways to get both regular reflection and Mach reflection. According to the studies for hysteresis phenomenon in transition (Ben-Dor et al. Reference Ben-Dor, Ivanov, Vasilev and Elperin2002; Hornung Reference Hornung2014), we may use a regular reflection solution (obtained for smaller $\theta _{w}$) as an initial condition to get regular reflection in the dual solution domain and a Mach reflection solution (obtained for larger $\theta _{w}$) as an initial condition to get Mach reflection in the dual solution domain. Using a uniform flow with $M_{0}=4$ everywhere as an initial solution, the steady solution of numerical simulation gives regular reflection in the double solution domain (Mouton & Hornung Reference Mouton and Hornung2007). To further demonstrate the possibility of Mach reflection, a Mach reflection solution with a lower Mach number, say $M_{0}=3$, is used as an initial solution and the numerical simulation is carried out with $M_{0}=4$ as the inflow condition until a steady solution is obtained.

The Mach number contours from numerical simulation with $M_{0}=4$ and $\theta _{w}=18^{\circ },20^{\circ },23^{\circ },27^{\circ }$ and $30^{\circ }$ are displayed in figure 7 for centred compression wave reflection and in figure 8 for shock reflection. The difference can also be seen from the hysteresis loop shown in figure 9 (more discussion about the Mach stem height will be discussed in the next section).

Figure 7.

Mach contours for centred compression wave reflection, showing the regular reflection domain ($\theta _{w}=18^{\circ }$), double solution domain ($\theta _{w}=20^{\circ },23^{\circ }$ and $27^{\circ }$) and Mach reflection domain ($\theta _{w}=30^{\circ }$), with $M_{0}=4$.

Figure 8.

Mach contours for shock reflection, showing the regular reflection domain ($\theta _{w}=20^{\circ }$), double solution domain ($\theta _{w}=22^{\circ },23^{\circ }$ and $24^{\circ }$) and Mach reflection domain ($\theta _{w}=26^{\circ }$), with $M_{0}=4$.

Figure 9.

The hysteresis loop in the $(H_{T}/H_{A}-\theta _{w})$ (where $H_{T}$ denotes the Mach stem height and $H_{A}$ denotes the inlet height) plane with $M_{0}=4$. (a) Shock reflection, (b) centred compression wave reflection.

For centred compression wave reflection with $M_{0}=4$, the double solution lies in $19.43^{\circ }<\theta _{w}<28.80^{\circ }$ according to the critical condition displayed in figure 5.

For $\theta _{w}=18^{\circ }$, we only have regular reflection according to the critical condition displayed in figure 5. Numerically, we indeed only observe regular reflection and the numerical result is displayed in figure 7(a).

For $\theta _{w}=20^{\circ }$, we should have both regular and Mach reflection according to figure 5. As shown in figure 7(b,h), we indeed have both regular reflection and Mach reflection.

For $\theta _{w}=23^{\circ }$, we also should have both regular and Mach reflection according to figure 5. As shown in figure 7(c,g), we indeed have both regular reflection and Mach reflection.

For $\theta _{w}=27^{\circ }$, we also should have both regular and Mach reflection according to figure 5. As shown in figure 7(d,f), we indeed have both regular reflection and Mach reflection.

For $\theta _{w}=30^{\circ }$, we should have only Mach reflection according to figure 5. Numerically we indeed only obtain Mach reflection and the numerical result is shown in figure 7(e).

For shock reflection with $M_{0}=4$, the double solution lies in $20.85^{\circ }<\theta _{w}<25.61^{\circ }$ according to the classical von Neumann condition and detachment condition. The numerical results displayed in figure 8) show that the double solution occurs for $\theta _{w}=22^{\circ },23^{\circ }$ and $24^{\circ }$, while for $\theta _{w}=20^{\circ }$, we only have regular reflection and, for $\theta _{w}=26^{\circ }$, we only have Mach reflection.

4.1. Mach reflection that lacks a clear triple point

It is well known that, for Mach reflection by a shock wave, there is a triple point that connects the incident shock, a reflected shock, a Mach stem and a slipline. All these four discontinuities have a different angle in the vicinity of the triple point (see, for instance, figure 8e–h). The flow between the slipline and the reflecting surface form a convergent–divergent duct that is quasi-one-dimensional.

However, the Mach reflection configuration of a centred comnpression wave, as shown in figure 7(e–h), displays the following differing features. (a) The reflected shock is highly curved by the centred compression wave. These compression waves weaken the reflected shock wave, since they are from the opposite family. (b) The Mach stem appears to result simply from the reflection of the leading Mach wave. However, this is possible only if the Mach stem is an inverted one. Although the curvature of the Mach stem can not be clearly identified, it can be argued that it is an inverted Mach stem. Note that the inverted Mach stem is convex towards the upstream direction and that the initial angle of the slipline is negative (Henderson & Lozzi Reference Henderson and Lozzi1979; Hornung Reference Hornung1986; Hekiri & Emanuel Reference Hekiri and Emanuel2015). (c) There is no clear triple point, the reflected shock and Mach stem appear to form a single curved shock and there is no distinct slipline (rather there are shear layers). (d) The flow below the slipline is far from being quasi-one-dimensional. It is divergent in the initial part and is then convergent. The divergent part increases the pressure to balance the pressure increase of the impinging compression Mach waves, while the convergent part decreases the pressure to balance the pressure decrease due to the impinging wedge trailing edge expansion wave.

4.2. Influence of $g$ and absence of wedge height induced transition

For shock reflection, it has been shown that when the relative wedge trailing edge height $g$ is small, the relative Mach stem height ${H_{T}}/{H_{A}}$ (where $H_{A}=y_{A}$ is the inlet height) decreases almost linearly with $g$ (Li & Ben-Dor Reference Li and Ben-Dor1997; Schotz et al. Reference Schotz, Levy, Ben-Dor and Igra1997). This means that Mach reflection may transit to regular reflection by increasing $g$. Vuillon, Zeiton & Ben-Dor (Reference Vuillon, Zeiton and Ben-Dor1995) anticipated that such transition occurs before the wedge trailing edge expansion fan interacts with the incident shock. Later on, Li & Ben-Dor (Reference Li and Ben-Dor1997) found that this transition occurs after the wedge trailing edge expansion fan interacts with the incident shock. Bai (Reference Bai2023) determined the shape of the incident shock during interaction and found the exact condition for transition. Due to the interaction between the wedge trailing edge expansion fan and the incident shock, so the incident shock is weakened and the Mach stem height decreases with $g$ more slowly than a linear curve.

One would expect that, for centred compression wave reflection, we have a similar phenomenon, i.e. Mach reflection to regular reflection transition should occur for some large enough $g$. But, as we shall see, this does not happen.

Figure 10 displays, for $M_{0}=4$, $\theta _{w}=30^{\circ }$, the Mach stem heights for different $g$. Figure 11 show the Mach number contour lines. We observe that $H_{T}/H_{A}$ varies almost linearly with $g$, i.e. it holds that

(4.1)\begin{equation} \frac{H_{T}}{H_{A}}\approx Ag+B, \end{equation}

where $A$ and $B$ are independent of $g$. According to figure 10, the linear curve (4.1) would intersect the axis $g$ if $g$ goes beyond $0.498$. However, such a direct intersection is impossible.

Figure 10.

Mach stem height as a function of $g$, with $M_{0}=4$ and $\theta _{w}=30^{\circ }$.

Figure 11.

Mach contours for $M_{0}=4$, $\theta _{w}=30^{\circ }$ with different $g$. Results are shown for (a) $g=0.35$, (b) $g=0.375$, (c) $g=0.4$, (d) $g=0.41$.

In shock reflection the wedge trailing edge expansion fan prevents the direct intersection of a similar linear curve (4.1) with the $g$ axis. In fact, interaction between this expansion fan and the incident shock occurs when $g>g_{max}$, with

(4.2a,b)\begin{equation} g_{max }=\frac{h_{max }/w}{h_{max }/w+\sin \theta _{w}},\quad \frac{h_{max }}{w }=\frac{\cos \theta _{w}\tan \beta _{01}-\sin \theta _{w}}{\tan (\theta _{w}+\mu _{1}) -\tan \beta _{01}}\tan (\theta _{w}+\mu_{1}) \end{equation}

according to Li & Ben-Dor (Reference Li and Ben-Dor1997) and Bai (Reference Bai2023). Here $\mu _{1}$ is the Mach angle in region (1) of figure 1, $\beta _{01}$ is the shock angle of the incident shock wave. Due to this interaction, the linear decrease (4.1) is replaced by a nonlinear curve (see figures 9 and 14 of Bai Reference Bai2023).

For centred compression wave reflection, we only have linear variation as given by (4.1) and have no intersection, according to figure 10. In other words, we have pure linear variation as given by (4.1) for some small values of $g$ and for larger $g$, there is no solution!

In the case of centred compression wave reflection, the last Mach wave of the centred compression wave is parallel to the leading characteristics of the trailing edge expansion fan, since between two simple waves (here the compression Mach waves and the wedge trailing edge expansion fan) is one uniform flow region where the characteristics lines are parallel. Hence, no interaction between the centred compression wave and the trailing edge expansion fan occurs. But this does not mean that the curve (4.1) can intersect the axis $g$ more easily than in shock reflection. In fact, it does not intersect the axis $g$ at all. The reason is given below.

When $g$ increases, the last point (as point $A_{5}$ in figure 2) of the wedge deflection part that produces the centred compression wave will approach the trailing edge (R). Assume that these two points coincide at $g=g_{max}$, i.e. $g_{max}$ is the value of $g$ at which the last point ( $x_{A_{K}}$,$y_{A_{K}}$) given by (2.10) coincides with the trailing edge $(x_{R},y_{R})$. This means that the maximum allowable value of $g$ is restricted by the encounter of the last point $A_{K}$ with the trailing edge (R).

Figure 12 gives the maximum values $g_{max}$. Not enough compression waves can be produced when $g>g_{max}$. For the present case shown in figure 10, with $M_{0}=4$, $\theta _{w}=30^{\circ }$, we have $g_{max}\approx 0.426$ according to figure 12, which is far below $g=0.498$ required for intersection in figure 10.

Figure 12.

The maximum value $g=g_{max}$ at which the last characteristics line of the centred compression wave coincide with the leading characteristics line of the trailing edge expansion wave.

In summary, for shock reflection with large $g$, it is the interaction between the wedge trailing edge expansion fan with the incident shock that prevents the intersection of a linear curve (4.1) with the axis $g$, while for centred compression wave reflection, when $g$ goes beyond some threshold shown in figure 12, the encounter of the last point ($x_{A_{K+1}}$, $y_{A_{K+1}}$) given by (2.10) with the trailing edge $(x_{R},y_{R})$ prevents any increase in $g$ at which the linear curve (4.1) intersects the axis $g$. However, transition from Mach reflection to regular reflection due to increasing $g$ can still occur for shock reflection, while this transition does not occur in centred compression wave reflection.

4.3. Influence of $\theta _{w}$

It is well known that, keeping other flow parameters fixed, increasing $\theta _{w}$ (or the shock angle of the incident shock wave) will increase the Mach stem height for shock reflection (see Hornung & Robinson Reference Hornung and Robinson1982). It is interesting to see whether the Mach stem height is increased or reduced when the incident shock is replaced by a centred compression wave.

For $M_{0}=4$, the Mach stem height variations as a function of the wedge angle $\theta _{w}$ are shown in figure 13 for both centred compression wave reflection and shock wave reflection, with $g=0.4$ and $0.45$.

Figure 13.

Mach stem heights for centred compression wave reflection and shock wave reflection with $M_{0}=4$. Results are shown for (a) $g=0.4$ and (b) $g=0.45$.

We observed the following two phenomena.

1. (1) For centred compression wave reflection, the relative Mach stem height $H_{T}/H_{A}$ varies with $\theta _{w}$ much more slowly than for shock reflection.

2. (2) For $\theta _{w}$ larger than some value, the relative Mach stem height $H_{T}/H_{A}$ for centred compression wave reflection is smaller than that for shock reflection, while for $\theta _{w}$ smaller than some value, the relative Mach stem height $H_{T}/H_{A}$ for centred compression wave reflection is larger than for shock reflection.

We have shown in § 3 that, for centred compression wave reflection, the von Neumann condition in terms of $\theta _{w}$ is lower than that for shock reflection. Thus, below the von Neumann condition of shock reflection and above the von Neumann condition of centred compression wave reflection, we have a finite height of the Mach stem in centred compression wave reflection. This is why for relatively small $\theta _{w}$, the Mach stem height is higher in centred compression wave reflection than in shock reflection. For a higher value of $\theta _{w}$, we fail to find a simple reason to explain why shock reflection has a higher Mach stem than in centred compression wave reflection.