2. Dimensional and scaling analyses, and the pipe flow map

An organizing framework is naturally suggested by a dimensional analysis of the problem of flow through a smooth, circular pipe. As illustrated schematically in figure 1(a), the relevant physical parameters involved are the pipe length $L$ and inner diameter $D$, the fluid density $\rho$ and viscosity $\mu$, the mean flow speed $U$, and the pressure difference $\Delta p$. These six quantities may be viewed as one dependent and five independent variables, e.g. $\Delta p(L, D,\rho,\mu, U)$. The five independent dimensional quantities can be reduced to two dimensionless groups by employing the Buckingham Pi theorem and noting that the three dimensions of mass, length and time are involved (Curtis, Logan & Parker Reference Curtis, Logan and Parker1982). The dependent quantity may also be non-dimensionalized, yielding in total three dimensionless groups with any one being viewed as a function of the others. Following common conventions, we select the flow Reynolds number $Re = \rho U D / \mu$ and the pipe aspect ratio $\alpha = L/D$ as independent variables that dictate the Darcy friction factor $f_D = 2 \Delta p D / \rho U^2 L$. The latter is a dimensionless form of pressure drop whereby the applied gradient $\Delta p / L$ is scaled by the inertial term $\rho U^2/2D$ relevant to well-developed turbulence (Acheson Reference Acheson1991; White Reference White2011). Hence all cases of pipe flow are encompassed by a function $f_D (Re, \alpha )$.

Figure 1.

An organizing framework for pipe flows. (a) Relevant variables. The pipe length $L$ and inner diameter $D$, the fluid density $\rho$ and viscosity $\mu$, and the flow speed $U$ dictate the pressure drop $\Delta p = \Delta p(L,D,\rho,\mu,U)$. (b) Scaling of terms in the Navier–Stokes equation. The applied pressure gradient (yellow) balances viscous (blue) and inertial (green and red) stresses, each of which follows a simple scaling. (c) Map of pipe flow regimes in the space of Reynolds number $Re$ and pipe aspect ratio $\alpha$. Three classical regimes of developed laminar, developed turbulent, and undeveloped inlet flows are associated with distinct domains of $(Re,\alpha )$. Each regime involves the applied pressure gradient predominantly balancing one other scaling term.

The classical limits correspond to regimes of $(Re, \alpha )$ that can be interpreted through a scaling analysis of terms in the governing Navier–Stokes equation. As shown in figure 1(b), the equation can be understood as a balance of the applied pressure gradient (yellow) with inertial (green and red) and viscous (blue) effects, each of which satisfies a scaling relation with the dimensional variables. We assert that the well-studied limits of pipe flow correspond to this balance being dictated principally by the applied gradient overcoming only one such effect, with the others playing negligibly small roles. For example, the applied gradient $\Delta p /L$ balances viscous resistance $\mu U / D^2$ for developed laminar flow, yielding the Hagen–Poiseuille law that applies for sufficiently slow flow through long, slender pipes, i.e. low $Re$ and high $\alpha$. Expressed in non-dimensional form, $f_D \sim Re^{-1}$ with no dependence on $\alpha$. As indicated in the blue region of figure 1(c), a mosquito drinking through its proboscis serves as a mascot of such laminar suction (Kim & Bush Reference Kim and Bush2012). Classical pipe flow turbulence corresponds to a balance of $\Delta p /L$ with inertial gradients $\rho U^2 /D$ transverse to the pipe axis, which applies to fast flows and slender pipes, i.e. high $Re$ and high $\alpha$. The dimensionless form is $f_D \sim \text {const.}$, independent of both $Re$ and $\alpha$. An elephant drawing water into its trunk might satisfy such turbulent suction (red). A third regime is associated with Torricelli's law for flow through an orifice or very short pipe, i.e. low $\alpha$, in which case $\Delta p /L$ is invested in overcoming the inertial gradient $\rho U^2 /L$ along the pipe axis. The dimensionless form is $f_D \sim \alpha ^{-1}$, independent of $Re$. This regime might be termed inertial slurping (green) and may relate to drinking tea or soup through pursed lips, which can be viewed crudely as forming a very short pipe.

A main result to be shown in this work is that the regimes have an interesting structure in which their dividing boundaries meet at a triple-point-like region. Moreover, the typical values of $Re$ and $\alpha$ during sipping through a straw will be shown to sit near this region, as indicated by the soda drinker in figure 1(c). Hence, while straw drinking differs from the idealized pipe flow problem studied here, this everyday experience can serve as a mnemonic for the ‘lawless’ borderlands between the well-studied hydraulic regimes and where the conventional relations therefore do not apply. This context also motivates the development of a universal hydraulic model that is informed by and validated against experimental measurements, and that spans the regimes and furnishes approximate pressure-rate relations applicable to intermediate cases.

3. Experiments

We carry out hydraulic measurements on pipes using an experimental system that allows for the exploration of wide ranges of $Re$ and $\alpha$. We specifically interrogate intermediate values of $Re$ and $\alpha$ that are between and somewhat into the classical regimes. The apparatus is a customized version of the commonly used scheme in which constant hydrostatic pressure drives flow through a conduit, and the flux or volumetric flow rate is measured. As shown in figure 2, the major components include a large tank that supplies the liquid, a reservoir into which the pipe drains, and an overspill system that maintains the water level in the supply chamber. The latter involves a pump whose rate is adjusted to be just higher than the flux lost through the pipe, the excess returning to the reservoir through an internal drain. The hydrostatic pressure difference $\Delta p = \rho g \Delta h$ is controlled and varied via a translation stage (not shown in figure 2, but symbolized by an arrow) that sets the height $\Delta h$ of the internal drain relative to the pipe. Here, $\rho$ is the density of the liquid, which is water and water–glycerol mixtures for these experiments. A given pipe is inserted through a hole in the chamber wall and secured via an external fitting. The liquid level in the supply chamber is monitored with a ruler and recorded after equilibration. The volumetric flow rate $Q$ is then measured by timing with a stopwatch the collection of a targeted volume in a precision beaker or graduated cylinder that intercepts the efflux from the pipe.

Figure 2.

Apparatus for hydraulic characterization of pipes and straws. Flow through a pipe is driven by the hydrostatic pressure associated with the depth $\Delta h$. The liquid level in the supply chamber is maintained by an overspill system consisting of a pump from a reservoir and an internal drain, whose height can be adjusted via a translation stage (represented by the arrow) in order to sweep through values of $\Delta h$. The volumetric flux $Q$ is measured by timing the collection of liquid within a beaker or graduated cylinder (not shown). The inset shows the chamfering applied to the inlet and outlet of all pipes.

We intend this experimental setting to target an idealized pipe flow problem that relates to and informs on tubular drinking but differs in several respects. Our focus is on smooth, rigid, straight pipes of circular cross-section, whereas the geometries of real straws and other conduits are more varied. Although liquid is typically raised against gravity during drinking, fixing the pipe horizontally isolates the hydrodynamic component of the problem. We impose a constant differential pressure and measure the mean flow rate over long times; an alternative would impose the rate and measure pressure. In contrast, drinking involves variations of pressure and flow. We will explore a sufficiently broad range of pressures and rates to cover typical drinking conditions (Nilsson et al. Reference Nilsson, Ekberg, Olsson, Kjellin and Hindfelt1996). The inlet condition adopted here involves drawing from a reservoir large enough to approximate quiescent fluid in the far field, which is an idealization of a straw or tube well away from the boundaries of a container. The outlet condition is a jet of liquid open to the atmosphere, whereas in straw drinking, the mouth is filled with air and liquid whose proportions change during a sip.

We assess 41 pipes made from high-polish stainless steel of inner diameters $D \in [0.1,0.8]$ cm and lengths $L \in [2,90]$ cm. The inlet and outlet edges are machined flat and then chamfered internally and externally (inset of figure 2). The length, height and width of the supply tank measure $40\,{\rm cm}\times 40\,{\rm cm}\times 20\,{\rm cm}$, chosen to be much larger than the pipe diameters. The overspill drain and pump input tube are located in the tank at the opposite end from the pipe in order to minimize flow disturbances. Each pipe is tested for approximately 10 values of $\Delta h \in [1,30]$ cm using pure water near room temperature, and we measure $Q$ three times to ensure reproducibility. The mean $Q$ for each condition is converted to a mean speed $U = Q/A$ across the pipe cross-section of area $A={\rm \pi} D^{2} / 4$. The data are cast in terms of the Reynolds number $Re = \rho U D / \mu$, aspect ratio $\alpha = L/D$, and friction factor $f_D = 2 \Delta p D / \rho U^2 L$. Lower values of $Re$ are attained for some pipes using two water–glycerol mixtures, whose density $\rho$ and viscosity $\mu$ are measured with a precision digital balance and ball viscometer, respectively. Temperature is monitored continuously and found to vary by at most $1\,^\circ \text {C}$ during each experiment for a given pipe and given fluid. The mean temperature is then used in the computation of the kinematic viscosity and thus $Re$ for the corresponding data set.

The entire set of measurements $f_D (Re,\alpha )$ is presented as markers in figure 3, where figure 3(a) shows the range and density of the data in the $(Re,\alpha )$ parameter space, and figure 3(b) provides a three-dimensional view. These plots are intended to introduce the scope and general character of the data, which comprise 697 total measurements spanning $Re \in [30,10\,000]$, $\alpha \in [2,200]$ and $f_D \in [0.04,3]$. All data are available in the supplementary spreadsheet available at https://doi.org/10.1017/jfm.2023.99. The faces of the markers in figure 3(a) are coloured according to the measured $f_D$ (see colour bar), and each horizontal array of data points corresponds to a specific pipe tested for a specific liquid. The background colour of figure 3(a) and the coloured surface of figure 3(b) represent the predictions of a model that will be developed in the next section.

Figure 3.

Master plots of pipe flow hydraulics with experimental measurements (markers) and model (coloured surface). (a) A view of the $(Re,\alpha )$ parameter space, with $f_D$ displayed as the marker face colour for experiments and the background colour for the model. The two show strong agreement across most of the space. (b) A three-dimensional view of the entire surface $f_D(Re,\alpha )$. (c) A transect at a fixed and high value of $\alpha = 100$. The data correspond to a single pipe tested across a range of pressures for pure water and a water–glycerol mixture, and error bars are described in the text. Also shown are dashed blue and red curves that correspond to the classical laws for developed laminar and turbulent flow, respectively. The black curve indicates the results of the current model. (d) A transect at a fixed and high value of $Re=6000 \pm 500$, where the experimental data correspond to many different pipes tested for pure water. Error bars are typically smaller than the symbol size. Also shown are curves for the laws of Torricelli (dashed green), turbulence (dashed red) and the current model (solid black).

To better reveal the trends, subsets of the data corresponding to horizontal and vertical transects in the space of $(Re,\alpha )$ are shown in the plots of figures 3(c,d). The curves are representative of high $\alpha$ and high $Re$, respectively, for which portions of the data are expected to align with the classical laws of pipe flow. For example, figure 3(c) considers $\alpha = 100$ (see inset), which ought to be large enough that the Hagen–Poiseuille law for laminar flow applies at lower $Re$, and turbulent effects dominate at higher $Re$. In the appropriate limits, the measurements (markers) indeed follow trends consistent with classical laws (dashed blue and red curves), the forms of which will be discussed in detail below. Our model (black curve) gives better correspondence across the entire range of $Re$. Similarly, figure 3(d) considers high $Re = 6000$ (see inset), for which the expectation of developed turbulent flow for large $\alpha$ is corroborated by the measurements. Very short pipes of low $\alpha$ are more consistent with a Torricelli-like law (dashed green curve), and our model agrees well with the data across all $\alpha$.

The experimental data of figures 3(c,d) include error bars, which are generally smaller than the marker size. The errors in $\alpha$ are negligibly small, as the pipe diameters are provided with tight tolerance and the lengths are measured accurately. Errors in $Re$ are computed based on the standard deviation of the three measurements of $Q$, whose variability is kept small by always collecting the pipe efflux over times of 40 s or longer. The error bars prove to be smaller than the symbol size for almost all the data of figures 3(c,d), and relative errors in $Re$ are typically 1 % and at worst 10 %. The errors in $f_D$ are associated predominantly with the pipe-to-surface height $\Delta h$ that appears in the calculation of the pressure. The location of the water surface can be measured with a precision of approximately 1 mm, and the depth of each pipe is taken as determined with an error equal to its radius. These effects compound to give relative errors that are generally under 5 % but can be as great as 30 %, which occurs only for the lowest values of $\Delta h$ in a given pipe–fluid data set.

4. Hydraulic model formulation

Here, we present a model that aims to account for the hydraulics of pipes of differing aspect ratios subject to flows of differing rates and with the specific aim of spanning the classical regimes of pipe flow. The end goal is a universal function $f_D(Re,\alpha )$. We take a hybrid theoretical–empirical approach that unifies and combines the many previous characterizations of smooth pipe hydraulics and especially aspects of flows through orifices, in the entrance region, developing and developed laminar and turbulent states, and the laminar-to-turbulent transition. Whenever possible, we appeal to theory or observations when making the many choices about the model structure and parameter values. Other aspects are dictated by mathematical simplicity or convenience, such as functions that combine smoothly different effects and have been employed in related works (Churchill Reference Churchill1977; Colebrook et al. Reference Colebrook, Blench, Chatley, Essex, Finniecome, Lacey, Williamson and Macdonald1939; Brkić & Praks Reference Brkić and Praks2018). Our model takes the general form

(4.1)\begin{equation} f_D(Re,\alpha) = f_D^I(Re,\alpha) + g^{L}(Re) f_D^L(Re,\alpha) + g^{T}(Re) f_D^T(Re,\alpha), \end{equation}

where $f_D^I$, $f_D^L$ and $f_D^T$ are functions that capture the individual contributions to the friction factor that come from inlet effects, laminar flow, and turbulent flow, respectively. This structure is motivated by the fact that inlet effects contribute for all pipes at all conditions and thus across the space of $(Re,\alpha )$, whereas laminar and turbulent effects are unique and apply within distinct ranges of $Re$. Here, $g^{L,T}(Re)$ are selection functions that take the value unity for $Re$ deep within the laminar and turbulent regimes, respectively, and zero elsewhere. We use logistic functions for this purpose, which behave like smoothed Heaviside or step functions:

(4.2a,b)\begin{align} g^{T}(Re) &= \frac{1}{1+\exp({-(Re-Re^{*})/\delta})} \nonumber\\ \text{and} \quad \quad \quad g^{L}(Re) &= 1 - g^{T}(Re) = \frac{1}{1+\exp({(Re-Re^{*})/\delta})}. \end{align}

Here, $Re^*$ is the critical Reynolds number at the laminar-to-turbulent transition, and $\delta$ can be interpreted as the width or range of $Re$ over which the transition occurs. The parameter value $Re^* = 2000$ is consistent with the literature on the transition in the presence of sufficiently strong disturbances. The choice $\delta = 200$ is shown below to yield an acceptable match to the experimental data.

We next set about defining the contributing frictional terms, starting with inlet effects. In the short-pipe or orifice limit $\alpha \to 0$, acceleration effects dominate and the applied pressure gradient is invested in axial inertial gradients $\Delta p / L \sim \rho U^2 / L$, corresponding to the green region of figure 1(c). The leading-order hydraulics is that of an ideal, inviscid fluid as described by Bernoulli's principle and Torricelli's law, which takes the form $\Delta p = \rho U^2 / 2$ or, equivalently, $f_{D} = 1/ \alpha$ (Semat & Katz Reference Semat and Katz1958; Fargie & Martin Reference Fargie and Martin1971; White Reference White2011; Malcherek Reference Malcherek2016). The actual efflux velocity is somewhat lower due to streamline contraction and viscous effects. These complexities determine the discharge coefficient $C_D \leq 1$ or ratio of actual-to-ideal efflux speed, whose value depends on $Re$ and the geometric details of the orifice (Wu et al. Reference Wu, Burton and Schoenau2002; Ferrante Reference Ferrante2012; Hicks & Slaton Reference Hicks and Slaton2014). We assume a constant $C_D = 0.85$ and thus $f^{I}_{D} = 1/ C^{2}_{D} \alpha$. The parameter value is within the broad range 0.6–1.0 reported in previous studies, and is chosen to account satisfactorily for the low-$\alpha$ portion of our experimental data set.

An accounting of the laminar flow contribution $f_D^L$ must include the developed flow far down the pipe as well as the developing flow in the entrance region. For sufficiently low $Re$ and high $\alpha$, the developed laminar flow involves the applied pressure balancing viscous stress, $\Delta p / L \sim \mu U / D^2$, corresponding to the blue region of figure 1(c). The developed flow profile is parabolic, and the hydraulics is described by the Hagen–Poiseuille law $\Delta p = 32 \mu L U / D^2$, which is equivalent to $f_D = 64 / Re$ (Stokes Reference Stokes1845; Acheson Reference Acheson1991; Batchelor & Batchelor Reference Batchelor and Batchelor2000; White Reference White2011). Viscous and inertial effects lead to an enhanced pressure drop in the entrance region over which the flow develops. Previous works have shown that the cumulative pressure drop coefficient $2 \Delta p (x) / \rho U^2$ increases with the streamwise coordinate $x$ before saturating at an order-1 value for $x$ much larger than the hydrodynamic entrance length $L_E$ (Sparrow et al. Reference Sparrow, Lin and Lundgren1964; Langhaar Reference Langhaar2021). Associating $x$ with $L$ and recasting in terms of $\alpha$ yields $f_D(\alpha ) = b(\alpha ) / \alpha$, where $b(0) = 0$ and $b \rightarrow b_\infty$ for $x \gg L_{E}$. We assume an exponential form for $b$ and adopt the empirical formula $L_E = k\,Re\,D$ for the length at which the flow profile is within 99 % of the developed parabolic profile, where $k = 0.05$ (Acheson Reference Acheson1991; Dombrowski et al. Reference Dombrowski, Foumeny, Ookawara and Riza1993; Batchelor & Batchelor Reference Batchelor and Batchelor2000; White Reference White2011). Hence the friction contributions from developing and developed laminar flow are given by

(4.3)\begin{equation} f_D^L = \frac{b_{\infty}}{\alpha} \left(1-\exp({-\alpha \ln 100 / k\,Re})\right) + \frac{64}{Re}, \end{equation}

where $b_\infty = 1$ is a simple choice that will be shown to yield satisfactory agreement with the experimental data. Previous theoretical studies indicate values in the range 1.2–1.4, while experiments are consistent with somewhat lower values, 1–1.2 (Campbell & Slattery Reference Campbell and Slattery1963; Sparrow et al. Reference Sparrow, Lin and Lundgren1964; Langhaar Reference Langhaar2021).

Finally, we take up the turbulent flow contribution applicable to sufficiently high $Re$. Well-developed turbulence for long pipes or high $\alpha$ involves a balance of the applied pressure gradient with inertial gradients transverse to the pipe, corresponding to $\Delta p / L \sim \rho U^2 / D$, which yields uniformly constant $f_D$ for the red region of figure 1(c). Extensive characterizations have shown that $f_D \sim O(0.01)$ and $f_D$ varies weakly with $Re$ (Colebrook et al. Reference Colebrook, Blench, Chatley, Essex, Finniecome, Lacey, Williamson and Macdonald1939; Moody Reference Moody1944; Nikuradse Reference Nikuradse1950; Langelandsvik, Kunkel & Smits Reference Langelandsvik, Kunkel and Smits2008; White Reference White2011; Adams et al. Reference Adams, Grant and Watson2012). Flow development effects in the turbulent regime have been shown to be confined to a relatively short entrance region whose length $L_E/D \sim O(10)$ is insensitive to $Re$ (Barbin & Jones Reference Barbin and Jones1963; Wang & Tullis Reference Wang and Tullis1974). The enhanced pressure drops due to development and inlet effects occur in the same region of the pipe and are thus not clearly distinguishable, and we make the simplifying assumption that the former leads to no additional contribution. Hence our model for the turbulent regime considers only fully developed flow, which is associated with a constant $f^{T}_{D} = f^{*}_{D} = 0.04$ that is representative of previously measured values 0.03–0.05 for $Re = 2000\unicode{x2013}10\,000$ (Moody Reference Moody1944; Langelandsvik et al. Reference Langelandsvik, Kunkel and Smits2008; White Reference White2011; Adams et al. Reference Adams, Grant and Watson2012).

In summary, the complete model has the form

(4.4)$$\begin{gather} f_D(Re,\alpha) = \frac{1}{C^{2}_{D} \alpha} + \frac{1}{1+\exp({(Re-Re^{*})/\delta})} \left[ \frac{b_{\infty}}{\alpha} \left(1-\exp({-\alpha \ln 100 / k\,Re})\right) + \frac{64}{Re} \right] \nonumber\\ {}+ \frac{1}{1+\exp({-(Re-Re^{*})/\delta})}\,f^{*}_{D}. \end{gather}$$

The six parameters and their values are $C_D = 0.85$, $Re^* = 2000$, $\delta = 200$, $b_\infty = 1$, ${k = 0.05}$ and $f^{*}_{D} = 0.04$.

5. Model results, comparison to experiments, and drinking straws

Here, we compare the model results to experimental measurements of pipes and drinking straws, and also use the model to interpret the hydraulic regimes and their boundaries.

5.1. Model results and comparison to experiments

The model prediction for $f_D(Re,\alpha )$ is presented as the coloured background in figure 3(a), and comparison to the face colour of the markers shows good qualitative agreement with the experimental measurements. The same model output is shown as the coloured surface of figure 3(b), where good correspondence with experiments is confirmed. The transects of figures 3(c,d) allow for a closer comparison, and the model predictions (black curves) show strong agreement with the measurements (markers). Also shown are dashed coloured curves representing the classical laws associated with Torricelli (green), developed laminar flow (blue) and developed turbulence (red). The respective formulas for $f_D$ are $1/ C^{2}_{D} \alpha$, $64/Re$ and $f^{*}_{D}$, as detailed in the previous section. These laws provide good matches to the data only in the appropriate limits of $Re$ and $\alpha$, whereas our model furnishes accurate predictions across the entire range of parameter values. Particularly for intermediate values of $Re \in [500,5000]$ and $\alpha \in [10,100]$, all existing laws do not apply, while our model accounts accurately for the fluid friction.

For a quantitative comparison, we assess the relative deviation of the model predictions from the experimental measurements, that is, $[f^M_D(Re,\alpha )-f^E_D(Re,\alpha )]/f^E_D(Re,\alpha )$, where the superscript $M$ and $E$ indicate model and experiment. This quantity is shown in figure 4(a), where the face colour on the experimental markers indicates the deviation as a percentage. Here, cyan tones indicate that the model overpredicts the measured friction, and magenta indicates an underestimate. White marks those data with deviations under 10 %, which is satisfied by approximately 75 % of the points.

Figure 4.

Comparison of experiments and model, identification of regime boundaries, and placement of drinking straws. (a) The signed deviation of the model predictions relative to experimental measurements. The deviations are largely unstructured in the parameter space, and typical mean squared values are under 10 %. (b) Regimes correspond to inlet (green), developed laminar (blue) and developed turbulent (red) flows. The data markers are coloured only if the experimentally measured friction is within 50 % of that predicted by the classical regime laws; they are white otherwise. The background is shaded via the same colour scheme for regions predicted by the model to lie within 50 % of these laws. The agreement of the marker and background colours indicates that the classical regimes are well identified. Boundaries (dashed lines) obtained by pairwise equating of the laws reveal a triple-point-like region. Three types of drinking straws are tested experimentally and found to reside near this point.

The mean of the relative deviations is under 1 %, and the standard deviation is 10 %. Deviations of this order are expected, since the model parameters $C_D$, $Re^*$, $b_\infty$, $k$ and $f^{*}_{D}$ are each determined only at the 10–30 % level based on previous studies. (The quantity $\delta$ can be viewed as a mathematical fitting parameter with no clear basis in pipe flow phenomena.) Further, our experimental errors can reach 30 % for the lowest pressures and lowest $Re$ for which a given pipe is tested with a given fluid. In light of these facts, the model can be seen as successfully furnishing predictions of accuracy of the order of 10 % for the hydrodynamic losses in finite-length pipes across intermediate $Re$.