Hostname: page-component-7b7567c8c-kwt9d Total loading time: 0 Render date: 2026-11-15T05:40:56.110Z Has data issue: false hasContentIssue false

Investigating the ratio of basal drag and driving stress in relation to bedrock topography during a melt season on Storglaciären, Sweden, using force-budget analysis

Published online by Cambridge University Press:  14 September 2017

Jim Hedfors
Affiliation:
Department of Earth Sciences, Uppsala University, Villavägen 16, S-752 36 Uppsala, Sweden E-mail: jim.hedfors@geo.uu.se
Vincent Peyaud
Affiliation:
Department of Earth Sciences, Uppsala University, Villavägen 16, S-752 36 Uppsala, Sweden E-mail: jim.hedfors@geo.uu.se
Veijio A. Pohjola
Affiliation:
Department of Earth Sciences, Uppsala University, Villavägen 16, S-752 36 Uppsala, Sweden E-mail: jim.hedfors@geo.uu.se
Peter Jansson
Affiliation:
Department of Physical Geography and Quaternary Geology, Stockholm University, S-106 91 Stockholm, Sweden
Rickard Pettersson
Affiliation:
Department of Physical Geography and Quaternary Geology, Stockholm University, S-106 91 Stockholm, Sweden
Rights & Permissions [Opens in a new window]

Abstract

We apply the force-budget technique using the isothermal block-flow model, on Storglaciaren, Sweden, to investigate the ratio between basal drag and driving stress in relation to a bedrock ridge in the bed topography during a peak melt season. The input data consist of glacier surface velocities collected using differential global positioning system surveying of a stake net and geometry from previous radar soundings and digitized ice surface maps. The study focuses on the effects of transverse bedrock ridges upon basal stress conditions. The pattern of the calculated ratio of basal drag and driving stress shows a rhythmical position of relatively high and low basal drags on the stoss and lee sides, respectively, of the bedrock thresholds. One of the zones of low basal drag corresponds to the location where the highest basal sliding rate has been measured previously by borehode deformation studies. This zone also aligns with the area where the drainage system is suggested to change from englacial to subglacial.

Information

Type
Research Article
Copyright
Copyright © The Author(s) [year] 2003
Figure 0

Fig. 1.Drilled and measured stake net on Storglaciaren: (a) overview showing ice depth (m) and surface elevation (ma.s.l.) as dashed and solid contours, respectively; (b) subsection of area outlined with a rectangle in (a), showing basal topography as dashed contours (m a.s.l.). Black dots are initial stake positions, and the fix-point is marked with x in (a). Stakes are labelled in a row–column fashion from 11 to 76 and 101 to 121, as marked in (b). The locations of the bedrock ridges are between 110 and 115 (R1) and near stake row 3 (R2) separated by the overdeepenings (OD1and OD2). Earlier borehole study sites are marked with circles accompanied by drilling year (84, 85 and 86). Coordinates are in Swedish RT 90 0.0 gon with the y axis (south–north) perpendicular to the major ice-flow direction. The x axis is aligned with the major flow direction (west–east). The grid interval is 200 (100) m in the x(y) direction.

Figure 1

Table 1.GPS campaign overview

Figure 2

Fig. 2.Velocity fields as interpolated from GPS measurements at the glacier surface (solid contours): (a) x component, Ux (m a–1); and (b) y component, Uy (m a–1). Arrows represent velocity resultants for each measured stake. Dashed contour lines are basal topography (m a.s.l.), and other map properties are as in Figure 1.

Figure 3

Fig. 3.(a) Calculated field of driving-stress resultants, τd(kPa) at the glacier bed (solid contours). (b) Calculatedfield of basal drag resultants, τb (kPa), at the glacier bed (solid contours). Arrows form a relative representation of the x and y components of driving stress and basal drag in (a) and (b), respectively. Other map properties are as in Figure 2.

Figure 4

Fig. 4.The ratio of basal drag and driving stress, τb/τd, at the glacier bed (solid contours). Values 4 1 (high) indicate that the basal drag exceeds the driving stress, while values 5 1 (low) indicate that the basal drag is lower than the driving stress. Earlier borehole study sites are marked with circles accompanied by drilling year (8 4, 85 and 86). Other map properties are as in Figure 2.