Hostname: page-component-7b7567c8c-fvjsw Total loading time: 0 Render date: 2026-11-17T06:14:39.793Z Has data issue: false hasContentIssue false

Investigation of shock dynamics in an axisymmetric inlet/isolator with attached boundary layers

Published online by Cambridge University Press:  15 December 2020

Michael D. Leonard
Affiliation:
Department of Mechanical and Aerospace Engineering, North Carolina State University, Raleigh, NC 27695, USA
V. Narayanaswamy*
Affiliation:
Department of Mechanical and Aerospace Engineering, North Carolina State University, Raleigh, NC 27695, USA
*
†Email address for correspondence: vnaraya3@ncsu.edu

Abstract

Shock oscillations within a model two-dimensional axisymmetric inlet with a constant area isolator are investigated under the condition of maintaining an unseparated boundary layer throughout the inlet/isolator section. Power spectral densities of the wall-pressure fluctuations beneath each shock leg intersecting the isolator surface exhibited a very low frequency broadband oscillation in the 10–100 Hz range as well as a very high frequency broadband oscillations above 10 kHz. Whereas the high frequency oscillations are attributed to the incoming boundary layer fluctuations, detailed investigations into the pressure fluctuation communication pathways within the isolator and their length scale of communication are made to elucidate the origin of the low frequency fluctuations. It was found that the downstream propagation of pressure fluctuations is primarily by the convection of the boundary layer structures and this communication occurred over several boundary layer thicknesses. The upstream propagation occurs through acoustic waves that extend over a distance of one local boundary layer thickness. Based on this understanding, a physical model is constructed, which makes an accurate prediction of pressure power spectrum of the low frequency shock wave oscillations; the model predictions also favourably compare with the shock oscillations in external shock boundary layer interactions without shock-induced flow separation.

Information

Type
JFM Papers
Copyright
© The Author(s), 2020. Published by Cambridge University Press
Figure 0

Figure 1.Axisymmetric inlet/isolator configuration as mounted within the wind tunnel with flow from left to right (dimensions normalised by the isolator diameter, $D$).

Figure 1

Figure 2.Experimental diagram of axisymmetric inlet/isolator with shock wave system sketch along with pressure transducer, Pitot probe and jet injection locations.

Figure 2

Figure 3.Mean and r.m.s. static pressure distribution along isolator wall. Comparison of Kulite transducer and extracted PCPSP trace at $\phi = 0^{\circ }$ for: $(a)$ mean pressure; $(b)$ r.m.s. pressure. Unwrapped PCPSP: $(c)$ mean pressure field measurements; $(d)$ r.m.s. pressure field measurements.

Figure 3

Figure 4.Empirical relation for the required pressure rise across the shock wave in order to cause separation of a turbulent boundary layer as compared with the maximum recorded pressure rise.

Figure 4

Figure 5.Flow visualisation of the isolator in the clean flow configuration (no jet injection): $(a)$ mean unwrapped full field-of-view surface-streakline field; $(b)$ combination mean PLS along the $r/D$ axis and surface-streakline images wrapped on a constant $r/D=0.5$ surface.

Figure 5

Figure 6.Velocity and Pitot pressure profiles across the isolator at $x/D = 6.33$: $(a)$ velocity profile; $(b)$ ratio between Pitot pressure and stagnation pressure of free stream.

Figure 6

Figure 7.Frequency pre-multiplied pressure spectral density of wall-pressure fluctuations measured beneath $(a)$ boundary layer at $x/D = 5.14$ located $0.24D$ upstream of the upstream shock leg; $(b)$ upstream and downstream isolator shock legs.

Figure 7

Figure 8.Power spectral densities of wall-pressure fluctuations measured: $(a)$ in the vicinity of upstream shock isolator impingement location; $(b)$ downstream isolator shock impingement location; $(c)$ at locations before and after upstream isolator shock impingement location.

Figure 8

Figure 9.Cross-correlation coefficient between upstream isolator shock impingement location and boundary layer in the upstream and downstream vicinity of the shock foot with the reference transducer beneath the shock foot across: $(a)$ a wideband time delay; $(b)$ a narrowband time delay.

Figure 9

Figure 10.Two-point cross-correlation coefficient between the pressure fluctuations at the upstream and downstream shock impingement locations with the upstream shock impingement location as the reference transducer across: $(a)$ a wideband time delay; $(b)$ a narrowband time delay.

Figure 10

Figure 11.Two-point cross-coherence of pressure traces between the upstream and downstream shock impingement locations to illustrate the shock oscillation coupling at different frequencies.

Figure 11

Figure 12.Frequency-multiplied PSD underneath shock impingement locations with various jet mass injection strengths: $(a)$ upstream shock impingement location; $(b)$ downstream shock impingement location.

Figure 12

Figure 13.Mean surface-streakline visualisation fields with sonic jet injection of mass ratios $\dot {m}_{jet}/\dot {m}_{iso}$ of: $(a)$ 1.3 %; $(b)$ 2.6 %; $(c)$ 3.9 %; $(d)$ 5.2 %; $(e)$ 6.6 %; $(f)$ 7.8 %. Dashed lines indicate where streaklines begin to deviate from the clean flow configuration while solid lines with arrows indicate streakline direction. Streaklines are symmetric approximately $\phi =0^{\circ }$ so only the lower half is marked with lines.

Figure 13

Figure 14.Isolator flow and pressure field with sonic jet injection of mass ratio $\dot {m}_{jet}/\dot {m}_{iso}=1.3\,\%$: $(a)$ mean surface-streakline visualisation field; $(b)$ comparison frequency pre-multiplied PSD of wall-pressure fluctuations measured beneath the isolator downstream shock foot ($x/D=7.22$) with and without jet injection; $(c)$ corresponding mean PLS field with jet injection; $(d)$ corresponding r.m.s. PLS field.

Figure 14

Figure 15.Illustration of the dominant sources that drive the shock oscillation at a given location.

Figure 15

Figure 16.Control volume schematic of proposed shock unsteadiness model.

Figure 16

Figure 17.Comparison of PSD of the wall-pressure fluctuation from the proposed model and the experimental data for the isolator downstream shock leg.

Figure 17

Figure 18.Comparison of wall-pressure fluctuation PSD from the proposed model and the measured PSD in: $(a)$ an external unseparated shock boundary layer interaction unit; $(b)$ inlet/isolator shock foot with $8^{\circ }$ inlet compression angle.